Winsome house WHSL454 User manual

Page: 1
Instruction, Use & Care Manual
Please save this manual for future reference.
Thank you for purchasing this Winsome House product. This product has been manufactured with the highest standards
of safety and quality.
Product Name:
Butterfly-Style Solar Wall or Step Motion Sensor Light
SKU #:
WHSL454
Operating Instructions
BEFORE USING THIS PRODUCT: READ, UNDERSTAND AND FOLLOW THESE INSTRUCTIONS.
How Your Solar Motion Sensor Light Works:
During the day, the solar charge panel included with this Butterfly-Style Solar Wall or Step Motion Sensor Light converts
sunlight into electricity recharging the batteries. Using this stored energy, the LED light turns on automatically at night
when motion is detected.
The light works with a built-in PIR (Passive InfraRed) sensing device which is continuously scanning for heat-source moving
in its detection scope. Once a heat source (such as a human or a car) is detected in that area, the light switches on
immediately and automatically to illuminate your pathways, steps, patios, porches, or anywhere you select for safety,
convenience, and security. The light remains on while the moving heat source stays in the detecting scope.
 Motion-activated light
Choosing a Location for Your Solar Motion Light:
 The solar light must be located in a position where it can get direct sunlight on the solar panel, and generally free
from cover and shade. When locating a suitable position for the unit, remember that it detects an area of about 120
degrees vertically and about 120 degrees horizontally, with a range of about 6 meters (19.7 ft). See figure above.
 Make sure that the photo sensor on the lamp body is not going to be affected by another light source, otherwise the
light will not illuminate at dusk.
 The solar light must be left to charge for two sunny days before first time use so that the best results are achieved.

Page: 2
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
Butterfly-Style Solar Wall or Step Motion Sensor Light
SKU #:
WHSL454
Operation:
 The button is located on the front of the solar wall light.
 The light features three modes, and is activated by pressing the button:
When pressing the button, the back led will flash, and determines which mode is selected successfully.
o Flash one time = Mode A (see below image)
o Flash two times = Mode B (see below image)
o Flash three times = OFF
 When the switch is in the OFF position, the lamp does not light up. The battery will charge in the OFF position.
 The output of the solar wall light will vary depending on the season. The light will stay on longer after a sunny day
rather than after an overcast day.

Page: 3
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
Butterfly-Style Solar Wall or Step Motion Sensor Light
SKU #:
WHSL454
Installation Tips
 Carefully remove the Solar Wall Light and all the fittings out of the box.
 Find a suitable location for your solar wall light. It can be mounted on an EXTERIOR WALL, STAIR TREAD,
MASONRY, OR WOOD POST.
Note: For installation on masonry, start by drilling holes for the plugs and the attachment screws. Insert
the plug (included), and make sure it is flush with the surface. The bottom screw must protrude from the
surface by at least 5mm (0.2in.) in order to attach the light.
 Use the template provided to measure the hole position correctly, and drill two holes of 6mm (0.24in.)
diameter.
 Insert expansion plug into each hole.
 Fix a screw to the lower expansion plug, and insert into the notch on the bottom of the light.
 Straighten the lamp, and fasten the upper screw.

Page: 4
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
Butterfly-Style Solar Wall or Step Motion Sensor Light
SKU #:
WHSL454
Battery
The light is equipped with an internal lithium battery, which is not replaceable. Please do not dispose of light in household
trash to avoid explosion.
Non-professionals: please do not disassemble the lamp.
Maintenance
To keep your solar motion sensor light looking new, keep the lens free of dust and deposits by wiping occasionally with a
dry or damp cloth.
Most important, ensure that the solar panel is kept free of dirt and debris at all times. A dirty solar panel will not allow the
batteries to fully charge, and this will shorten the life of the batteries and may cause the light to not function properly.
Technical Specifications
LED Light Setting: 220 Lumens / 1.5W Plus
LEDs: SMD2835 x 14pcs (Front 12pcs; Back 2pcs)
Beam Angle: 90 deg.
Rechargeable Battery Type: Li-ion Battery 1200mAh / 3.7v (not replaceable)
IP Degree: IP65 Waterproof
Lifespan: 35,000hrs
Installation height: <4m (13ft.)
Solar Panel: 0.7Wp, Poly-crystalline silicon
High Light activation (range): 10 seconds
Charge Time (minimum): 6 Hours
Motion Sensor Range: 6 meters (19.7 feet); 120 degrees

Page: 5
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
Butterfly-Style Solar Wall or Step Motion Sensor Light
SKU #:
WHSL454
Troubleshooting:
Light will not switch
on when there is
movement in the
detection area
 Ensure that the power on the main body has been turned on (Mode A or Mode B).
 Ensure that the motion sensor has been positioned to face oncoming movement.
 Ensure that the battery has been fully charged in direct sunlight for one sunny day.
 Check to see that the solar cell charge panel is facing south so that it receives direct sunlight for
most of the day, enabling the battery to fully charge.
 Check to see that the solar panel is not near the night time light sources, such as street lights.
Light switches on
during the day
 Ensure the wall light is not placed in shady area.
 Ensure the solar panel is facing towards direct sunlight.
Light switches on for
no apparent reason
 Moving trees, traffic, pet, or birds may be getting in the area of detection. This may be unavoidable;
however, the sensor could be redirected to a height where this less likely to occur.
 If there are reflective objects in the detection area, such as windows, water, or white walls, you may
need to redirect or possibly reposition the motion sensor.
 Test the motion sensor by covering it completely with cardboard, and waiting several minutes to
make sure it does not detect motion.
Light quickly flashes
on and off
 Battery charge may be low. Turn the power to the OFF, and charge the battery for two (2) sunny
days, ensuring the solar cell charge panel has been placed in direct sunlight.
Light is not as bright as
normal
 Battery charge may be low. Turn the power to the OFF, and charge the battery for two (2) sunny
days, ensuring the solar cell charge panel has been placed in direct sunlight.