Winston WNI-6712 User manual

1/33
RF433 and 2.4G wireless barcode scanner user manual
Launch date：2020-9-23
1.Ver：V3.9
Revision record
2020/9/23 Rev 3.9
1. New character output method: Shift-JIS Japanese
2019/5/29 Rev 3.8
1. Remove the settings that do not match the code.
2. The version specification is revised based on Src-0085 V3.4 and Src-0083 V3.4.
2018/11/30
1. Classification character output setting code
2017/8/9 Rev 3.3
1. Add wireless channel setting code
20017/9/14 rev 3.4
1. Modify the input and output character format setting code
20170915 Rev 3.5
1. Increase keyboard case detection settings
2. Increase the small keyboard switch settings
20170125 Rev3.6
1. Increase proximity matching

2/33
Content
1 . Comprehensive settings( Please read the red part before make settings)............... 3
2. An asterisk (*) in the description part indicates the factory default parameters.......3
3.2 Set command data format......................................................................................... 4
4. Setting barcode type..................................................................................................... 6
4.1 Pairing command★.................................................................................................... 6
4.2 HID-KEYBOARD multi langue setting★...................................................................... 7
4.4 Check parameter........................................................................................................8
4.5 Operation mode★......................................................................................................8
4.6 Character input/output/keyboard format setting................................................... 10
4.6.1 Case control and keypad switch............................................................................ 10
4.6.2 Out put format and function key setting.............................................................. 11
4.7 Sleep times setting★................................................................................................11
4.8 Restore the factory settings★..................................................................................12
4.9 0x0A filter.................................................................................................................. 12
4.12. Output data way (USB/USB VCP) ★......................................................................13
4.14 Auto trigger configuration................................................................................... 14
4.9 The command of firmware upgrade.........................................................................15
4.10 Wireless connectivity detection............................................................................. 15
(★Note: this function only in a scanner connected to a receiver)............................... 15
4.11 The sender wired output........................................................................................ 16
4.13 Serial port setting ★...............................................................................................17
4.15 Start symbol mode setting(Prefix) ★.....................................................................18
4.16 End symbol mode setting(Suffix)............................................................................18
4.17 Sender end Prompt sound selection at the sender.............................................. 19
5. Information instructions:............................................................................................ 20
5.1 Receiver end instructions system........................................................................... 20
5.2.1 Receiver end LED light indicator...........................................................................21
6. 2.4G Wireless sending and receiving data packet format......................................... 22
6.1 bk2425 Infinite packet format.................................................................................. 22
7.Inventory mode to save and read data packet format：...........................................23
7.1 Inventory model management information storage format:.................................23
8.433 wireless data packet............................................................................................. 24
The packet format...........................................................................................................24
9. ACK packet format...................................................................................................... 24
10. Symbol table..............................................................................................................25

3/33
1 . Comprehensive settings( Please read the red part before make settings)
1.1 Setting instruction description
1. The setting bar code is uniformly printed with Code128 type CODE B set bar code.
2. An asterisk (*) in the description part indicates the factory default
parameters.
（1）Scan: Enter setting mode “@SET”. After enter setting, it will exit the setting mode if next setting
command is not scan within 20s.
（2）Scan: the relevant setting barcode. In this step, you can scan one or more setting barcode
commands.
（3）Scan: Exit and save “@END”.
（4）The setting of some functions can directly scan the corresponding quick setting bar code. Such as:
pairing barcode, unpairing barcode, etc.

4/33
3.2 Set command data format
Table 3.3-1 Setting command data format table①
Prefix
Setting goals
Type
Parameter
WN-
T-/R-/W-
Refer to "Set Barcode Type
Table"
*****
Notice ①This format does not include instructions for entering settings and saving and exiting settings.
Table 3.3-2 Set instruction data format analysis
Format
Data
Description
Prefix
WN-
Fix prefix symbol
Setting goals
T-/R-/W-
T-:Means to set the barcode directly to the sender end.
R-:Means to set the barcode directly to the receiver end,
and the setting bar code of the receiving end
needs to be forwarded by the sending end
through wireless transmission.
W-:The sender end and receiver end work at the same
time
Type
Refer to "Set Barcode Type Table"
Parameter
The parameter is 4 characters in the range of "0~9"

5/33
3.4 Set barcode type table
Table 3.4-1 Set barcode type table
Type
Description
A
Wireless pairing/unpairing
B
Multi-language settings
C
View firmware information/Modify frequency
D
Infrared sensor trigger switch
F
Real-time mode / inventory mode / inventory mode data operation
G
Sleep time
H
Restore default setting
I
Data transmission form, start symbol mode setting, custom start
symbol
K
Sending/receiving end firmware upgrade command
L
USB wired output switch
3.5 “Enter setting” and “Save and exit”
Command：
Function
Command
barcode
Remark
Enter setting
@SET
Enter the setting prompt sound,
effective time of 20 seconds
Save and
exit
@END
Save and exit settings prompt sound
Note: 1. For the setting of non-quick setting commands, it must first scan to enter the
setting command, then scan the corresponding parameter setting command, and
finally scan to save and exit the setting command.

6/33
4. Setting barcode type
4.1 Pairing command★
Function
Command
barcode
Remark
Start
pairing
@.WN-T-A0001/
Can be paired
remotely
Close
pairing
@.WN-T-A0002/
Only allow pairing
Note: 1. The effective time of pairing is within 20S from the moment the receiver is powered on (the LED
is flashing). After 20s, the LED is always on and cannot be paired. (This method is for the
receiver without buttons)
2. Press the receiver button, the receiver will automatically enter the pairing state, during this
period it can be paired normally. (This method is for the receiver with buttons).
3. 2.4G stops flashing after pairing successfully.

7/33
4.2 HID-KEYBOARD multi langue setting★
Function
Command
barcode
Remark
@SET
*USA
WN-W-B1000
FRENCH
WN-W-B1001
GEMRAN
WN-W-B1002
TUKISH
WN-W-B1003
BELGIUM
WN-W-B1004
BRAZIL
WN-W-B1005
CRZCH
WN-W-B1006
SPANISH
WN-W-B1007
Latin America
@END
Note: This setting code is valid for both the receiving end (Tx) and the sending end (Rx). If multiple
languages are set when the wireless transmission connection is disconnected, the sending end language
setting will be successful, but the receiving end language will not change.

8/33
4.4 Check parameter
Function
Command
barcode
Remark
Output parameter of
system
WN-W-
C1000
1> Firmware version
2> Battery level
3> Wireless channel
Explanation : The command to view the parameters is sent to the receiver along with the system
parameters, and each parameter is separated by a terminator, such as:
PKT{protocol field|WN-W-B1001|parameter 1+0x0D|parameter 2+0x0D |……} (the content of the data
packet in {})
4.5 Operation mode★
Function
Command
barcode
Remark
*Real-time
mode
@.WN-T-
F0000/
Scan and transfer, fail alarm
Cache
mode
@.WN-T-
F1000/
On the basis of real-time mode,
increase the buffer data after
transmission failure. The system
will automatically upload the
cached data after detecting that the
device has not been operated for
three seconds. If the cached data is
not uploaded when the machine is
turned off, the system will continue
to detect the upload after the next
startup until the transmission is
completed.
Inventory
mode
@.WN-T-
F2000/
The barcode data is automatically
stored, and it is uploaded once after
scanning "Upload Data"; scanning
"Clear Data" to clear the data in the
memory "Scan "Data Total" to
view the total number of data in the
memory
After scanning the barcode, the
data is directly stored in the
barcode scanner, and the data will
not be deleted until the [Clear
Data] is scanned. During this
period, you can scan [upload data]
to send the data to the receiver or
directly upload to the PC
Upload data
@.WN-T-
F2001/
Upload barcode data

9/33
Data sum
@.WN-T-
F2002/
Upload the sum of barcode
Clear data
@.WN-T-
F2003/
Clear the barcode data in the
inventory mode
Notice☆:1. Six command in operation mode are all quick setting command, the setting is successful
when scan them successful.
2. Upload data, data amount, clear data in inventory mode, these three operation setting
command is unavailable when enter setting mode, if it is already in setting mode, must save
and setting before using these three operation setting command.
3. New 433 and 2.4G solution (model number：WNI-xxx2, WNI-xxx3,WNC-xxx2,WNC-xxx3)
Storage data description:
①Inventory mode: storage length is 30 Byte data will be able to store 49,000pcs
②storage length is 13Byte data will be able to store 104,500pcs
③Cache mode:storage length is 30 Byte data will be able to store 14,200pcs
④storage length is 13Byte data will be able to store 30,300pcs

10 /33
4.6 Character input/output/keyboard format setting
4.6.1 Case control and keypad switch
Function
Command
barcode
Description
*Uppercase key
(CapsLK) detect
on
@.WN-W-
F3201/
Turn on uppercase detection,
keyboard Caps will not affect the
output
example: barcode
content:123ABCdef
Turn on Caps output:
123ABCdef
Turn off Caps output:123ABCdef
Uppercase
key(CapsLK)
detect off
@.WN-W-
F3202/
After turn off the caps detection,
the keyboard Caps lock will
affect the output
example: barcode
content :123ABCdef
Turn on Caps output:123abcDEF
Turn off Caps output:123ABCdef
Turn on Numeric
keyboard
@.WN-W-
F3203/
After turn on, it need to set the
output to GBK format. If the
language is German at this time,
it needs to be set to English, and
other languages do not need to be
set.