Wisenet HCD-6080R User manual

High Resolution Camera
User Manual
HCD-6080R
HCV-6080R

High Resolution Camera
User Manual
Copyright
©2017 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the
registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed,
partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal
guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsi-
bility. Hanwha Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.

Before operating the camera, confirm the camera model and correct input power voltage.
To help you understand this manual thoroughly, we'll introduce our model description.
■ HCD-6080R/HCV-6080R SERIES
 
    
    
■ 
 
_
 •
→
→


4_ safety information
safety information
CAUTION


CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this appliance
to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with
the installation instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.

English_5
●safety information
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled
with water on top of the camera. doing so may cause personal injury due to fire, electric shock,
or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric
shock.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never disassemble
or modify this product in any way. (Hanwha Techwin is not liable for problems caused by
unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause fire
or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 55°C), low temperature (below
-10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may
cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
damage the CMOS image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.

6_ safety information
safety information
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed
of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb
indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
 (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

English_7
●important safety instructions
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the
cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as powersupply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or
“LPS” and rated from 24 Vac (50/60 Hz) min.0.37 A or 12 Vdc, min.0.32A. (HCB-6000)
16. If you use excessive force when installing the product, the camera may be damaged and
malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.

8_ important safety instructions
17. Do not install the product in a place where chemical substances or oil mist exists or may be
generated. As edible oils such as soybean oil may damage or warp the product, do not install
the product in the kitchen or near the kitchen table.
This may cause damage to the product.
18. When installing the product, be careful not to allow the surface of the product to be stained
with chemical substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the
product’s surface.
19. If you install/disassemble the product in a manner that has not been recommended, the
production functions/performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
20. Installing or using the product in water can cause serious damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
Hanwha Techwin cares for the environment at all product manufacturing
stages, and is taking measures to provide customers with more environmentally
friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating
environmentally friendly products, and indicates that the product satisfies the
EU RoHS Directive.
important safety instructions

English_9
●Contents
contents

10
10 Features
11 Components and Accessories
13 Component names and functions

15
15 Before installation
15 Installation
20 Adjusting the monitoring
direction for the camera

22
22 Connecting to Monitor
23 Connecting to Power
24 Using Coaxial Communications

26
26 Menu Configuration
26 Menu Setup

40
40 Troubleshooting

41
41 Specifications
43 Dimension

10_ introduction
introduction

yHigh Resolution
Use of a 2.1 mega pixel CMOS device provides clear pictures with a resolution of 1920x1080.
yExcellent Sensitivity
-
Color : 0.11Lux (F1.6, 1/30sec)
B/W : 0Lux(IR LED on)
y
High performance DSP Chip removes noises of GAIN resulting from the low light level and
shows a vivid, high definition video even in the dark place.
y
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions to
provide optimum colors, and B/W mode operates in night-time conditions to enhance
the definition of the image.
y
You can set a mode according to the camera installation conditions.
- BASIC, DAYNIGHT, BACKLIGHT, ITS, INDOOR, USER
yWDR
By adopting a proprietary high performance DSP chip, the camera delivers clear,
high quality pictures even in backlight, by increasing exposure in dark areas while
decreasing it in bright areas; a corrected image with clear details results.
y
HLC(High Light Compensation), REVERSE , SHARPNESS and PRIVACY functions are
provided.
y
Using SIMPLE FOCUS, you can easily adjust the focus.
yCommunication
AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron)
CCP (CVI Coax Protocol), TCP (TVI Coax Protocol)
y
The camera’s OSD is complimented by 16 languages.
- English, Korean, Japanese, German, Italian, French, Spanish, Russian, Czech, Polish,
Romanian, Serbian, Swedish, Danish, Turkish, Portuguese

English_11
●introduction

Check if the following items are included in the product package.
<HCD-6080R>
Camera 
Screws Template


12_ introduction
introduction
<HCV-6080R>
TOP
FRONT
Camera  Template
Tapping Screw  
Card-type moisture
absorbent 

English_13
●introduction

1 Dome Cover
2 Shield Case
3 Rotate base : control rotating angle of camera.
4  3.2 ~ 10mm (F1.6).
5  Display the menu on the screen and move the cursor to four directions
to confirm status or after changing a selected item.
Simple Focus: Press the SET button for more than 2 seconds.
 Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
6 
7  Control panning angle of camera.
8 
9 Ground Terminal
❿ Motion detection signals are output through this terminal.
⓫  Video signals are output through this port. Connect this port to the Video IN
port of a AHD DVR.
⓬  These infrared LED’s are controlled by the illumination sensor.
⓭ IIIumination sensor : Detects incoming light to control the IR LED.
HCD-6080R
2
3
4
5
6
9
8
1
7
❿
⓭
⓬
⓫

14_ introduction
introduction
1 Dome Cover
2 Rotate base : control rotating angle of camera.
3  3.2 ~ 10mm (F1.6).
4  Display the menu on the screen and move the cursor to four directions
to confirm status or after changing a selected item.
Simple Focus: Press the SET button for more than 2 seconds.

Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
5 
6  Control panning angle of camera.
7 
8 Ground Terminal
9 Motion detection signals are output through this terminal.
❿  Video signals are output through this port. Connect this port to the Video IN
port of a AHD DVR.
⓫  These infrared LED’s are controlled by the illumination sensor.
⓬ IIIumination sensor : Detects incoming light to control the IR LED.
HCV-6080R
TOP
FRONT
2
3
4 5
❿
8
7
1
9
⓬
6
⓫

English_15
●InstallatIon

Ensure you read out the following instructions before installing the camera:
y
yYou have to check whether the location (ceiling or wall) can bear five times the weight of your
camera.
y
yDon’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
y
yBefore installing your camera, you have to adjust the lens focus, zoom, and switch settings.
y
yWhen installing your camera, don’t allow any person to approach the installation site.

Disassembling(HCD-6080R)
1. Use one hand to hold the camera’s bottom
part and turn the cover counterclockwise with
another hand to separate it.
2. Lift up the shield case to separate it.
Installation
Shield Case

Installation
16_ Installation
Disassembling(HCV-6080R)
Using the L-wrench provided, loosen 3 screws by turning them counterclockwise
and separate the dome cover.
TOP
FRONT
Dome Cover
L Wrench

English_17
●InstallatIon
Installation(HCD-6080R)
1. Attach the installation template to the
selected area and punch 2 holes as shown
in the fi gure.
2. Use the 2 supplied screws to fi x the
camera to the 2 punched holes.
ySet the <TOP FRONT> mark imprinted on
the camera to face the direction of camera
monitoring.
3. Adjust the lens in a desired direction by
referring to the“Adjusting the monitoring direction for the camera” section.
4. Attach the dome cover and the shield case to the main body.
M
`Pay attention to the direction for assembly.
케이블 구멍

Installation
18_ Installation
Installing the camera on a ceiling or wall(HCV-6080R)
1. Drill holes on the ceiling by matching to the holes on the case bed, and insert
plastic anchors (HUD 5) (not included) fully into the holes. Fix the case bed on the
ceiling by using screws . (3 places)
2. Connect Power and video cables and arrange them through the hole you want to pass
when mounting the main body on the mounting bracket, note that not to damage or
squeeze the cables.
TOP
FRONT
screw
TOP
FRONT
Video output jack
Function jack
Power input terminal

English_19
●InstallatIon
3. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring
direction for the camera”section.
4. Close the dome cover.
`To ensure waterproofing, tight up the fixing bolts using the L-wrench.
TOP
FRONT
Dome Cover
L Wrench
M
`The installation should be done by qualified service personnel or system installers.
`If the ceiling material is not strong enough to hold the installation screws, the camera
may fall off. Reinforce the ceiling as needed.

Installation
20_ Installation

Pan
Tilt Lens rotation
TOP
FRONT
Pan
Tilt Lens rotation
<HCD-6080R>
<HCV-6080R>