Wizard 20100040 User manual

\Handouts\CMCConvertibleStand
02/15/08
-1-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
Wizard™ CMC Convertible Stand
Assembly Instructions
Parts List
Box 1: Full Size Box 4: Half Size
Part Qty Description Part Qty Description
20000011 2 Base Sides 20000011 2 Base Sides
20000021 2 Crossbars 20000031 2 Half Size Crossbars
20000041 1 Front Panel/Wizard Sign 20000051 1 Half Size Wizard Sign
20000061 2 4mm Allen Wrenches 20000061 2 4mm Allen Wrenches
20000071 2 17mm Wrenches 20000071 2 17mm Wrenches
20000081 1 Driver Pak Basket 20000081 1 Driver Pak Basket
20000141 1 M6x1x15mm Screw (extra) 20000141 1 M6x1x15mm Screw (extra)
20000161 1 M6x1x25mm Screw (extra) 20000161 1 M6x1x25mm Screw (extra)
20000241 1 M6x1x45mm Screw (extra) 20000241 1 M6x1x45mm Screw (extra)
Box 2: Full Size 20000091 2 Cradle Sides
Part Qty Description 20000111 1 Half Size Stabilizer Panel
20000091 2 Cradle Sides 20000121 2 Board Stops
20000101 1 Stabilizer Panel 20000061 2 4mm Allen Wrenches
20000121 2 Board Stops 20000161 1 M6x1x20mm Screw (extra)
20000061 2 4mm Allen Wrenches Box #2 Computer Box
20000161 1 M6x1x20mm Screw (extra) 30-00025-1 2 8500e Board Extenders
20-25009-1 2 Screw 5/16-18x2”BHCS
21-40631-1 2 Nut, Nylock 5/16”18UNC/HEX
Product Number
20100040 - Full Size Convertible Stand 20100070-Half Size Convertible Stand
Screw and Threaded Collars
Note that most screws and collars are pre-installed. Simply unscrew the installed screws and use them to
attach the items using the same hole.
Wizard™International, Inc. PO Box 66, 4600 116th St. SW. Mukilteo, WA 98275-0066 425/551-4300 wizardint.com
Wizard™Instructions
Wizard™Instructions

\Handouts\CMCConvertibleStand
02/15/08
-2-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
Dimensions
You have two options when assembling the convertible stand: Angled and Upright. Because both
use the same Cradle Side piece, you will need to make this determination about halfway through the
installation process. The Driver Pak Basket is on the left side in either assembly.
The Angled Convertible Stand (Fig A) with the Wizard installed is 50” Deep, and 72” wide, bottom
edge is 36” High, and lies at a 15 degree angle. This conguration is not recommended for the CMC
Model 8500e.
The Upright Convertible Stand (Fig B) with the Wizard installed is 38” Deep, and 72” wide, bottom
edge is 29” High, and lies at a 45 degree angle. This conguration can be used with the CMC Model
8500e.
Fig A. Fig B. Fig C.
Fig A: Angled Stand. Fig B: Upright Stand. Fig C: Upright Stand with Board Stops for the 8500e.
Attach crossbars
1. Lay out the Base Sides and the crossbars (Fig A). Note that the bar closest to the front of the Base
Side is angled at the top, and the side bar of the Base Side slopes down toward the front. Make sure
to keep the screws and holes for the Driver Pak Basket on the left outside side when assembling (Fig
B).
Fig A. Fig B.
Fig A: Lay out the Base Sides and the crossbars. Fig B: Note which side of the Base Side is the front, and make sure that
the screws for the Driver Pak Basket is on the left side.

\Handouts\CMCConvertibleStand
02/15/08
-3-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
2. Unscrew the eight screws from the bottom of the Base Sides and use them to attach the crossbars
to the Base Sides (Fig C). The crossbars are installed to the inside of the Base Sides (Fig D). The
crossbars are now attached to the Base Sides (Fig E).
Fig C. Fig D. Fig E.
Fig C: Attach the crossbars to the Base Sides. Fig D: Crossbars are installed to the inside of the Base Sides. Fig E: The
crossbars are attached to the Base Sides.
Attach Front Panel
1. Remove the four screws from the front of the Base Sides and use them to attach the Front Panel
(Wizard Sign) to the front of the Base Sides. The Front Panel is now attached (Fig B).
Fig A. Fig B.
Fig A: Attach the Front Panel. Fig B: The Front Panel is now in place.

\Handouts\CMCConvertibleStand
02/15/08
-4-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
Remove Board Stop
1. Locate the Board Stops that are installed into the end of the Cradle Sides (Fig A). Remove the Board
Stops from the Cradle Sides (Fig B) and set them and the screws and threaded collars aside for later
(Fig C). This Board Stop will not be used for the 8500e; the 8500e will be using a Board Extender.
Fig A. Fig B. Fig C.
Fig A: Cradle Side. Fig B: Remove Board Stop. Fig C: Note there are two kinds of Board Stops.
Attach Cradle Side
1. Now you need to determine if you want an angled stand or an upright stand. Note that each con-
guration uses the same Cradle Side (Fig A), but it is placed in a different orientation depending upon
the type of stand you want. The photos below show the Board Stops already installed, merely to help
reference which conguration you want -- you will be installing the Board Stops soon.
Figure B. shows the Cradle Side for the angled stand.
Figure C. shows the Cradle Side for an upright stand.
Figure D. shows the Cradle Side for an upright stand with Board Extenders for use with 8500e.
Fig A. Fig B. Fig C. Fig D.
Fig A: Cradle side. Fig B: Cradle side placed for angled Stand. Fig C-D: Cradle side placed for upright Stand - Recom-
mended for 8500e.

\Handouts\CMCConvertibleStand
02/15/08
-5-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
2. Remove the four large 10x1.5x120mm Hex Head Bolts, washers and nuts from the Base Sides
and use them to attach the Cradle Side to the Base Sides (Fig E). Put a at washer on each side of
the Base Side and Cradle Side, and place the lock washer next to the nut. Use each of the 17mm
Wrenches on either side to make it easier (Fig F).
Fig E. Fig F.
Fig E: After placing the Cradle Side into the desired position, attach it to the Base Sides . Fig F: Use the 17mm Wrenches
to attach the nut to the bolt.
Attach Stabilizing Panel and Driver Pak Basket
1. On the back of the Cradle Sides, remove the two upper screws, them remove the two screws from
the back of the Base Sides and use them to attach the Stabilizing Panel (Fig A). The stabilizing panel
must attach to both the Base Sides and the Cradle Sides (Fig B-C).
2. On the left side of the Base Sides, remove the six screws and use them to attach the Driver Pak
basket to the left side of the Base Sides (Fig D).
Fig A. Fig B. Fig C. Fig D.
Fig A: Attach the back stabilizing panel. Fig B-C: The stabilizing panel must attach to both the Base Sides and the Cradle
Sides. Fig D: Attach the Driver Pak basket to the left side of the Stand.

\Handouts\CMCConvertibleStand
02/15/08
-6-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
Attach Board Stop/Extender
Take note which Board model you are assembling the Convertible Stand for, and follow the appropri-
ate directions below.
Board Stops for the 8000/8500
Attach the same Board Stops you removed earlier, to the bottom end of the Cradle Sides (Fig A-B),
using the screw and collar that you removed earlier. Make sure the “feet” of the Board Stops are
facing upward, as the CMC will be resting against them (Fig B).
Fig A. Fig B.
Fig A: Install the Board Stops to the end of the Cradle Sides. Fig B: Board Stops installed.
Board Extenders for the 8500e
For the 8500e, you will use the longer Board Extenders (Fig A), located in Box #2 - Computer Box.
Attach the long Board Extenders to the bottom end of the Cradle Sides, using the bolt and nut that
are included with the Extender. Make sure that the “V” of the Board Extender is facing upwards, as
the CMC will be resting against them.
Fig A.
Fig A: Board Extenders for the 8500e.

\Handouts\CMCConvertibleStand
02/15/08
-7-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
Placing the Wizard CMC onto the Convertible Stand
The Wizard CMC is now ready to mount onto the Convertible Stand. Get another person to help, and
place the Wizard CMC onto the Stand (Fig A-C). Make sure the bottom edge of the Wizard CMC is
seated against the Board Stops/Extenders.
Fig A. Fig B. Fig C.
Fig A: Angled Stand. Fig B: Upright Stand. Fig C: Upright Stand with Board Stops for the 8500e.
Look at the back of the Wizard CMC and make sure that you avoid pinching the airlines on the back,
and that none of the threaded washers are touching the Stand (Fig D). Position it side to side wherever
you’d like it to be; the right end of the machine can be within 4” of a wall if necessary.
Screw a screw into the hole in the Board Stop/Extender and into the Board, and secure into place
(Fig E).
Place the Driver Pak into the Driver Pak Basket (Fig F). Hook up the pneumatic and electrical con-
nections. You have now installed your Wizard CMC onto the Convertible Stand.
Fig D. Fig E. Fig F.
Fig D: Don’t pinch airlines or threaded washers on the stand. Fig E: Screw a screw into the Board Stop/Extender into
the Board to secure it into place. Fig F: Place the Driver Pak into the basket.

\Handouts\CMCConvertibleStand
02/15/08
-8-
Wizard™ International, Inc., 4600 116th St. SW, PO Box 66, Mukilteo, WA 98275 888/855-3335 Fax: [phone] wizardint.com
NOTES: