Wiznet WIZ6000 User manual

-1 -
WIZ6000 User’s Manual
(Version 1.0)

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 2 -
Document Revision History
Date Revision Changes
2010-03-15 V1.0 Release

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 3 -
Certification Information
CE for Class B ITE
INFORMATION TO THE USER
Hereby, WIZnet. Declares that this WIZ6000 is in compliance with the essential requirements
and other relevant provisions of directive 1999/5/EC.
WARNING: This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC for Class B ITE
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
Guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
KCC for Class B ITE
INFORMATION TO THE USER
This equipment has been tested for a Class B digital device.
-Trade Name orApplicant : WIZnet, Inc.
-Equipment Name : Serial to Wireless LAN Device Server
-Basic Model Number : WIZ6000
-Manufacturer / Country of Origin : WIZnet, Inc. / KOREA
-Certification Number : WWW-WIZ6000-S2W(B)
WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference.

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 4 -
WIZnet’s Online Technical Support
If you have any questions about our products, please visit our website and submit your
questions on the Q&A Board. We will reply your questions as soon as possible
COPYRIGHT NOTICE
Copyright 2010 WIZnet Co., Ltd. All Rights Reserved.
Technical Support: [e-mail]
Sales & Distribution: [e-mail]
For more information, visit our website at http://www.wiznet.co.kr
C
CL LI IC CK K

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 5 -
Contents
1. Introduction .............................................................................................................................................................. 1
1.1 Products Contents ............................................................................................................................ 2
1.2 Product Specification ...................................................................................................................... 3
1.3 WIZ6000 Device server Interface ............................................................................................... 5
1.3.1 Hardware Installation .................................................................................................................... 5
2. Hardware Specification ........................................................................................................................................ 6
2.1 WIZ6000 Dimension .................................................................................................................................. 6
2.2 Connector Specification ........................................................................................................................... 7
2.2.1 RJ-45 Connector ............................................................................................................................. 7
3.2.2 RS-232C Connector ....................................................................................................................... 7
3. Demonstration and Test ...................................................................................................................................... 8
4. Serial Configuration ............................................................................................................................................ 12
5. Warranty .................................................................................................................................................................. 20

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 6 -
Figures
FIGURE 1. WIZ6000 DEVICE SERVER INTERFACE ......................................................................................................... 5
FIGURE 2. WIZ6000 DIMENSIONS (UNIT : MM) .......................................................................................................... 6
FIGURE 3. RJ-45 PIN ASSIGNMENT .............................................................................................................................. 7
FIGURE 4. SERIAL TERMINAL PROGRAM CONFIGURATION ........................................................................................... 8
FIGURE 5. WIRELESS NETWORK CONNECTION ............................................................................................................. 9
FIGURE 6. NETWORK TERMINAL PROGRAM CONFIGURATION .................................................................................... 9
FIGURE 7. RECEIVED DATA BY NETWORK TERMINAL PROGRAM ............................................................................. 10
FIGURE 8. SERIAL TO WIRELESS LAN 구성 ............................................................................................................... 10
FIGURE 9. DEVICE TERMINAL PROGRAM .................................................................................................................... 11

WIZ6000 User’s Manual (WIZnet Co,. Ltd.)
- 7 -
Tables
TABLE 1. PRODUCTS CONTENTS. .................................................................................................................................... 2
TABLE 2. PRODUCTS SPECIFICATION – WIRELESS ......................................................................................................... 3
TABLE 3. PRODUCTS SPECIFICATION - SOFTWARE ........................................................................................................ 3
TABLE 4. PRODUCTS SPECIFICATION - HARDWARE .................................................................................................... 4
TABLE 5. RS-232 PIN ASSIGNMENT ............................................................................................................................. 7
TABLE 6. SERIAL CONFIGURATION FRAME FORMAT ................................................................................................... 12
TABLE 7. SERIAL CONFIGURATION REPLY FRAME FORMAT ....................................................................................... 12
TABLE 8. SERIAL CONFIGURATION STX & ETX ......................................................................................................... 12
TABLE 9. SERIAL CONFIGURATION REPLY CODE ......................................................................................................... 13

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 1
1. Introduction
WIZ6000 is the external gate way module which provides a bridge for RS-232 or Ethernet to
IEEE802.11 b/g wireless communications. Devices with the interface of RS-232C serial or
Ethernet can established a wireless network which can enable remote monitoring, management
and controlling.
WIZ6000 has been designed by using WIZ610wi WiFi module. Therefore all functions and
operations are identical with WIZ610wi.
Refer to the ‘WIZ610wi User Manual’ for detail description.
Main Features
Embedded 802.11b/g Wireless Networking
Access Point, Client, Gateway, Serial to WLAN mode Supported
Ethernet to Wireless Bridging
Strong Security with 64/128 bit WEP, WPA, WPA2(AES), SSL
Support Ethernet port, Serial port, Reset Button
Ready to use serial to wireless application
Max 25Mbps Data Streaming
Compact design 90.5mm X 94.5mm X 22.7mm ( L x W x H )
RoHS Compliant
CE, FCC and KCC certificated

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 2
1.1 Products Contents
WIZ6000 Device Server
Included Dipole Antenna
(2.5dBi SMAType)
Serial Cable
Network Cable
(Crossover Cable)
Power
(DC 5V / 2A Adaptor)
Data CD
(Manual, H/W & SW related Materials)
Table 1. Products Contents.

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 3
1.2 Product Specification
Wireless
ITEM Specification
Wireless Standard IEEE802.11b/g
Frequency Range 2.412~2.485GHz
Output Power
(Tolerance(+/-1dBm)
802.11b: 15dBm@11Mbps (Max 10mW / 1MHz)
802.11g: 13.5dBm@6~54Mbps (Max 10mW / 1MHz)
Receive Sensitivity 802.11b: -65dBm@11Mbps
802.11g: -76dBm@54Mbps
Data Rates 54Mbps-1Mbps
Modulation Type 11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
11b: DSS(CCK, DQPSK, DBPSK)
Table 2. Products Specification – Wireless
Software
ITEM Specification
Operation Mode Access Point, Clinet, Gateway, Serial to Wireless LAN
Protocol ARP, UDP, TCP, Telnet, ICMP, IGMP DHCP, PPPoE,
BOOTP, HTTP, TFTP
Security
WEP 64/128big
WPA/WPA2 PSK/AES/TKIP
802.1x(Radius)
SSL
Management HTTP, Telnet, Serial, UDP
Notification Event Logging
Table 3. Products Specification - Software

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 4
Hardware
ITEM Specification
Interface Ethernet 1 Port, RS-232C 1 Port, DC 5V Power input
2.5dBi SMA type Dipole Antenna
Temperature Operation: -5℃~55℃
Storage: -20℃~70℃
Humidity Operation: 10% to 90%, Non-Condensing
Storage: 5% to 90%, Non-Condensing
Serial
(RS-232C)
Baud Rate : 230,400bps
Stop bits: 1
Parity: None, Odd, Even
Flow Control: XON / XOFF (Software),
CTS / RTS (Hardware), None
Power DC 5V input
Power Consumption Under 600mA( 3.3V )
Dimension 90.5mm X 94.5mm X 22.7mm (Excluded antenna size)
Table 4. Products Specification - Hardware

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 5
1.3 WIZ6000 Device server Interface
Figure 1. WIZ6000 Device Server Interface
1.3.1 Hardware Installation
STEP1: Connect the WIZ6000 to the HUB or PC by using a network cable.
STEP2: Connect the WIZ6000 to the serial device by using the RS-232C serial cable.
STEP3: Insert the power supply connector to the WIZ6000 by using the 5V / 2A
DC power adaptor.
STEP4: Configure the network parameters of WIZ6000 and your PC.
- The default IP address of WIZ6000 is “192.168.1.254”.
Your PC’s IP address should start with these three sets of numbers “192.168.1.XXX”.
- WIZ6000 and PC can be connected through wireless network.
Connect to WIZ6000 from PC by using default SSID “WLANAP”

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 6
2. Hardware Specification
2.1 WIZ6000 Dimension
A 90.5 B 67.5 C 11.5 D 14.5
E 26.0 F 27.0 G 5.2 H 6.3
I 4.5 J 7.0 K 22.5 L 9.0
M 8.0 N 11.5 O 16.5 P 9.0
Q 22.5 R 87.5 S 94.5
Figure 2. WIZ6000 Dimensions (unit : mm)

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 7
2.2 Connector Specification
2.2.1 RJ-45 Connector
Ethernet port Pin outs
Pin Signal
1 TX+
2 TX-
3 RX+
6 RX-
Figure 3. RJ-45 PIN Assignment
3.2.2 RS-232C Connector
Serial port Pin outs
6 987
21 43 5
Pin Number Signal Description
1 H/W Trigger Hardware Trigger signal Input
2 RxD Receive Data
3 TxD Transmit Data
4 EXT_GND External Power Ground (Internally shorted to GND)
5 GND Ground
6 NC Not connect
7 RTS Request To Send
8 CTS Clear To Send
9 EXT_VCC External Power Input (5V) / Optional
Table 5. RS-232 PIN Assignment

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 8
3. Demonstration and Test
In this chapter, an example is provided for you to test the functionality of WIZ6000. The testing
environments are the followings:
<Hardware>
A PC equipped with a RS-232 serial port
WIZ6000 Device Server
Connect PC and module’s Ethernet port by using an Ethernet Cable
(Direct or Crossover)
Connect PC and module’s serial port by using a serial cable
<Software>
Hyper Terminal (or any other terminal program)
yStep 1.
① Connect the PC and WIZ6000 by using a serial cable.
② Connect the PC and WIZ6000 by using an Ethernet cable.
③ Turn on the power switch of WIZ6000.
yStep 2. : WIZ610wi Environment Setup
① On your PC, go to the “Network Setting” and connect to your WIZ6000 in the “Wireless
Network Connection”.
② In your web browser, input IP address of WIZ6000 (Default : 192.168.1.254).
If configuration page appears, click “Serial setup” menu and set the serial parameters.
yStep 3. : Data Transmission
① Execute terminal program at the PC. (Ex: Hyper Terminal)
② Set the baud rate as the same value of WIZ6000.
Figure 4. Serial Terminal Program configuration

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 9
③ Connect to “WIZ6000” in the Wireless Network Setting of your PC
Figure 5. Wireless Network Connection
④ Execute one more terminal program, and set IP address and Port number.
Figure 6. Network Terminal Program configuration
⑤ Input any characters in the Hyper Terminal for Serial. (In the example below, “01234567890”
is input).
The same characters are outputted in the Hyper Terminal for Network.
A Serial to Wireless LAN test was performed. (Serial to Ethernet )

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 10
Figure 7. Received Data by Network Terminal Program
Figure 8. Serial to Wireless LAN 구성
⑥ In the same way, input any character at the screen of terminal program for network, and
check if same character is displayed at the screen for serial. ( Ethernet to Serial )

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 11
※The above test can also be performed in a program called, “Device Terminal program”, which
is easy and simple to use.
Figure 9. Device Terminal Program
Device Terminal is a program which integrates both serial and network communications into one
user interface so that you can test your WIZnet gateway module easily.
As shown in above Figure, the upper part of the program allows you to configure your serial
setting of WIZ6000. By clicking the “Open” button, serial communication is enabled.
The lower part of the program allows you to configure the network settings. You can test both
TCP Client and TCP Server modes at the same time. If the Server Mode is enabled, Device
Terminal will operate as server mode, and the WIZ6000 module will work as client mode. The
PC where the Device Terminal is operating will work as a server, the IP address of the PC
should be set as Server IP of the module. If Server mode is not checked, Device Terminal will
operate as client mode, and the module as server. For the IP address and port, please input
your IP address and port number of WIZ6000 and click the “Connect” button to start a network
communication.
When serial and network terminals are connected, input any character in the Data Input window
and click “Send” button. You can check the data is transferred into the another window.

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 12
4. Serial Configuration
Serial Command Format
It is possible to configure WIZ6000 by using serial command.
RS-232C port’s Pin number 1 of WIZ6000 is Hardware trigger pin.
( ‘1’: H/W trigger disable, ‘0’: enable )
< Frame Format >
Command Frame format
Descriptor STX Command code Parameter ETX
Length(bytes) 1 2 Variable 1
Table 6. Serial Configuration Frame format
Reply Frame format
Descriptor STX Reply code Parameter ETX
Length(bytes) 1 1 Variable 1
Table 7. Serial Configuration Reply Frame format
STX & ETX
Setting Comments
STX ‘<’ : Hex = 3Ch
ETX ‘>’ : Hex = 3Eh
Table 8. Serial Configuration STX & ETX
Reply Code
Reply Comments
S Command was successful
F Command failed
0 Invalid STX
1 Invalid command

WIZ6000 User’s Manual (WIZnet Co., Ltd.) 13
2 Invalid parameter
3 Invalid ETX
E Enter Serial Command Mode
Table 9. Serial Configuration Reply Code
Command Code
Com
mand
Get/
Set Comments Parameter Time
Network
RF Get
Firmware
Version vx.x.x 1
RA Get MAC Address
0:Ethernet MAC address, 1:Wireless MAC address,
<0xx.xx.xx.xx.xx.xx_1xx.xx.xx.xx.xx.xx> 1
RI Get IP Address <Sxxx.xxx.xxx.xxx> 1
WI Set IP Address <xxx.xxx.xxx.xxx> 2
RS Get Subnet Mask <Sxxx.xxx.xxx.xxx> 1
WS Set Subnet Mask <xxx.xxx.xxx.xxx> 2
RG Get Gateway <Sxxx.xxx.xxx.xxx> 1
WG Set Gateway <xxx.xxx.xxx.xxx> 2
RD Get DHCP Server
1:Enable, 0:Disable
<Sx> 1
WD Set DHCP Server
1:Enable, 0:Disable
<x> 2
RH Get
DHCP
Start/End IP
Start address_End address
<Sxxx.xxx.xxx.xxx_xxx.xxx.xxx.xxx> 1
WH Set
DHCP
Start/End IP
Start address_End address
<xxx.xxx.xxx.xxx_xxx.xxx.xxx.xxx> 3
DL Get
Wireless
Active Client
List
MAC address_Channel_TxRate_RSSI
<Sxxxxxxxxxxxx_xx_xx_xx[:xxxxxxxxxxxx_xx_xx_xx:…]> 1
RL Get
DHCP Client
List
<IP address_MAC address>
<Sxxx.xxx.xxx.xxx_xxxxxxxxxxxx[:xxx.xxx.xxx.xxx_xxxxxxxxxx
xx:…]>
1
WV Set DNS Server 1:Enable, 0:Disable 1