Woner HC816B User manual

Professional Hair Clipper
USER MANUAL


Cutting Length Control 4
Remove and Install Blade 5





CONTENTS
........................
................................................
...........................................
..........................
...................................................
........................................
...............................................
Cleaning and Maintenance 2
To Charge 3
Features 1
.............................
..................................................
Warning 6
Guarantee Card 7
Specification 3
Contact Us 8

Features
Universal
Voltage Charger
Cleaning Brush Universal Voltage Charger small sack
1
Ceramic Blade
Titanium Blade
Length Control
ON/OFF
LED Display
L
Thin
R
Combs
3mm 6mm 9mm 12mm
15mm
15mm Right guard
Left guard Thin guard

2
Cleaning and maintenance
Clean Blade
Maintain Blade
1. Clean up the blade with
cleaning brush.
2. The blade can be removed
for cleaning.
3. The moving blade can be turned back on, and then clean up the hair
between the moving blade and the fixed blade.
1. Please drop oil on the red point before or
after using the product to reduce wear and
extend blade life.
2. Keep the oil blade away from children.
3. Place it away from heat, sparks and other
ignition sources.
feed tool
post
moving blade
fixed blade

Specification
Charge
12
1. Be certain clipper is OFF.
2. Insert the adaptor directly into the clipper and plug the appliance plug into
any output.
3. It will take about 2.5 hours to fully charge the clipper.
4. LED Display shows 100, which means fully charged.
2000mAh Li-ion
Battery
Motor
Professional
Electronic
Hair Clipper
Operating voltage:3.7V
Centering material:anti-wear brass
Charging Time: About 2.5 Hours
Running Time: About 4 Hours
Input:100V-240V50/60Hz
Output:AC 5V---1000mA
Specific Adapter
3

Cutting lengths
A. 8 guides from 3mm, 6mm, 9mm, 12mm,15mm
B. 5 lengths setting from 0.8mm to 2.0mm
1. Decide cutting length
2. Select the right guide combs
3. Adjust cutting length setting from 0.8mm to 2.0mm
Remove the butted positions with hands
on its both sides and then remove the
Limit comb installation
Like the picture, hold both sides and
bush when butt: the button positions
Nnotes: the comb should noit be loose
or easy to fal l bff after being butted
L imit comb dismantle
comb
The unlock key needs to be pressed
Moving the button up and down to adiust
the blade(0.8mm-2.0mm)
while adjusting
4
3mm
3mm
6mm 9mm 12mm
6mm 9m m 12mm
L
Thin
R
15mm
15mm Right guard
Left guard Thin guard
1.
4
2
.0

Remove and Install Blade
Remove Blade
Install Blade
Adjust the adjusting ring to 2.0mm
Direct the blade(B)at the hair
Push the blade down until it clicks
before installing the blade
clipper’s slot(A)and plug in
Please hold with the other hand to
avoid the blade falling off.
Like the picture,press down the moving blade
with the thumb and then remove the blade.
5
A
B
1.
4
2
.0

Warning
3. The product can only be cleaned by cloth with little water
or mild soap solution
4. Do not charge the product under environment above40 or
below0℃
The product can produce little heat during using or charging, which is normal
ex Please remove the battery safely and return it to the specified places when the
it casually
1. Please do not dissemble the product
2. The hair clipper can not be washed Please keep it away
from wet conditions
6
batteryruns out. Never discard

Product Assurances
1.This product has been manufactured through the precise quality management and
inspection process.
2.In case of any failure during the normal operation, customer may send to the retailer
or maintenance center for free-of-charge maintenance.
3.Free services shall not be provided in either case below:
D. Any damage caused by non-compliance with notes as stated in the this user manual
C. Any damage caused by natural disaster and abnormal voltage
B. Any damage caused by mistake, inadvertent use or accident
A. Any damage caused by the maintenance and transformation
4.This warranty card shall be the only proof of warranty, while the product maintenance
against invoice shall not be allowed
Product Name
Product Model
Purchasing Date
Professional Hair Clipper
with Lithium Battery Warranty Period
One year from the
purchasing date
Month Date Year To Month Date Year
Customer Address
Address
Point of Sale
Name
Name
Phone
Number
Name
Phone
Number
7
Guarantee Card

Please feel free to contact us if you have any questions
about the item. We will be happy to deal with it.
Guangzhou Laoji E-Business Co., Ltd
Tailuyingli Street, Tianhe District,
Contact US
8
Room D1033A, NO.8,
Guangzhou Province, China
[e-mail]
Woner Hair Clipper
f
510507