Wonwoo SF-H308 Installation instructions

STAINLESS STEEL CAMERA
INSTALLATION / OPERATING MANUAL
- Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
- The design and specifications are subject to be changed without prior notice to improve
product’s quality.

TABLE OF CONTENTS
1. PRECAUTIONS
1. 1 IMPORTANT SAFETY INSTRUCTION
2. DISCRIPTIONS
2. 1 PACKAGE COMPONENTS
2. 2 PART NAMES AND FUNCTIONS
3. OPERATION SETTING
3. 1 EXTERNAL I/O
4. INSTALLATION
5. MAIN SETUP MENU
5. 1 Camera Setting
5. 2 Inteligence Setting
5. 3 Special Setting
5. 4 Factory set
5. 5 System Reset
6. SPECIFICATION
6. 1 Mechanism Specification
6. 2 Camera Specification
7. DIMENSION
3
3
4
4
4
5
5
6
09
09
24
34
37
37
38
38
39
40
02

1. 1 Important Safety Instruction
•
Read these instructions.
•
Pay attention on all the warnings.
•
Follow all instructions.
•
Arbitrary disassembly will void product warranty.
•
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
•
Do not dissemble or insert foreign objects.
•
Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
•
Do not aim the camera at the sun or any other strong light source.
•
Do not install the camera in intermittent lighting environments.
•
Only use attachments/accessories specified by the manufacturer.
•
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
•
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
Installation should be done only by qualified personnel and conform to all local codes.
•
Installation should be done in a place strong enough to hold it.
•
Use only installation methods and materials capable of supporting four times the maximum specified load.
•
To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
•
These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
•
Only use replacement parts recommended by manufacturer.
•
This manual is subject to change without notice for product improvement.
1. PRECAUTIONS
03

2. 1 PACKAGE COMPONENTS
2. 2 PART NAMES AND FUNCTIONS
2. DISCRIPTIONS
Camera body Rotation bracket
Wall bracket(Option) Pole bracket(Option) Corner bracket(Option)
Sunshield/Sunshield bolt
Seal fitting
Nipple
2. Camera Housing : Camera module and windshield wiper system are installed in the main housing.
1. Windshield Wiper : Wipes away water or dust on the camera screen.
3. Sunshade : Protects the system from sunlight and unwanted reflections.
4. CableEntry : Attached on Seal fitting.
5. Screw for Grounding : Used to connect grounding wires.
1
3
5
4
2
04

3. 1 EXTERNAL I/O (HD-SDI TYPE + IP TYPE)
RY1_NO(White)
RY1_NC(Brown)
RY1_COM(Red)
IP_DO_COM(Orange)
IP_DO_NO(Blue)
IP_DO_NC(Green)
IP_DIN(Brown)
GND(Black)
RS_TRX+(Red)
RS_TRX- (Orange)
RS_TX+(Blue)
RS_TX-(Green)
MIC_IN(Green)
SPK_OUT(White)
GND(Black)
ALARM1(Yellow)
ALARM2(Orange)
GND(Black)
HD-SDI(Blue)
CVBS(Yellow)
LAN
AC24V_A (Red)
AC24V_B (Black)
3. OPERATION SETTING
Set the protocol, address and dipswitch before set the camera.
The manufacturer is not responsible for any problems after disassembling
and reassembling by whom is not explosion-proof certificate holder
or explosion-proof certificate approval company.
05

4. INSTALLATION
Precautions before installation
Ensure you read out the following instructions before installing the camera:
• Install the system based on the following directions. If you want to install using a different
method, you should confirm the safety recommendations by making a request to
the manufacturer in advance.
• The gross weight of the system is 7 kg. Be careful when lifting the system, and put on
proper anti-slip gloves.
• It must be installed on the area (ceiling or wall) that can withstand 4 times the weight of
the camera including the installation bracket.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
How to install seal fitting in the cable entry
1. Install the conduit seal system according to the EN60079-14 standard.
2. Check items that are installed together with screws, conduit sealing parts, etc.
3. After connecting screws to the cable entry, tightly connect the seal fitting with
an explosion-proof nipple.
4. Pass cables that are connected to the outside through the seal fitting.
Conduit sealing parts should obtain ATEX certification.
5. Insert sealing parts by referring to the next figure.
•Use sealing compounds that have obtained UL certification.
Sealing compound
Fiber Filler
06

How to install Sunshade
Connect the sunshade to the camera housing with screws
using a wrench.
How to install a rotation bracket on the system
1. Assemble the rotation bracket under the housing bracket using
3 or 4 screw bolts according to the angles.
2. Install the rotation bracket on the floor using screw bolts.
How to install the grounding wires
1. Insert the grounding wires into the cable terminal.
2. Fix the terminal using a cable clamping tool.
3. Connect the grounding cables with the external earthling rod.
• When the camera is installed on a concrete floor,
be sure to use an M8 anchor bolt.
•Use screws that can support at least 4 times
the weight of the system.
•Do not disassemble the system while it is operating.
You can disassemble the system for maintenance 30 minutes after
the power is shut off.
1
2
3
07

How to install wall brackets on the system
1. Assemble the wall bracket under the rotation bracket
using 4 screw bolts.
2. Install the wall bracket on the wall using screw bolts.
•When the camera is installed on a concrete floor,
be sure to use an M12 anchor bolt.
•When the camera is installed on a concrete floor,
be sure to use an M12 anchor bolt.
How to install a pole bracket on the system
1. Assemble the pole bracket under the rotation bracket
using 4 screw bolts.
2. Install the pole on the pole bracket using a steel band.
How to install wall/pole brackets
on the system
1. Assemble pole bracket sides with
the wall bracket using a set of 4 bolts.
- Bolt set M12 bolt X M12 spring washer
X M12 nut (2EA)
2. Install the pole on the pole bracket
using a steel band.
How to install a corner bracket on the system
1. Assemble corner bracket sides with the wall bracket using a set of 4 bots.
- Bolt set M12 bolt X M12 spring washer X M12 nut (2EA)
2. Install the corner bracket on the wall using screw bolts.
08

09
5. MAIN SETUP MENU
CAMERA MENU
CAMERA MENU
- Functions can be set-up using the Camera menu.
In this menu, user can set the zoom, focus, white balance, auto exposure...etc functions.
Decide using of digital zoom function and select zoom speed.
5. 1. 1 ZOOM MODE
- ZOOM SPD
ZOOM SPD : Select from 0steps to 7 steps,
USER (Standard speed)
Select : or Set ON : Set OFF :
NEAR NEAR
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
STABILIZER
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ ZOOM MODE >
▷
▷
▷
▷
▷
▷
▷
▷
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
STABILIZER
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ ZOOM MODE >
▷
▷
▷
▷
▷
▷
▷
▷
Camera menu subject to be changed without prior notice to upgrade and quality increase
and we may use slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual
menu is not matched.
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : OFF
BACK
▷
< NEAR / RIGHT ▷ ZOOM SPD >
MAIN MENU
CAMERA SET
INTELIGENCE
SPECIAL FUNC
FACTORY SET
SYSTEM RESET
EXIT
▷
< NEAR / RIGHT ▷ CAMERA >
▷
▷
▷
5. 1 Camera Setting

10
- D-ZOOM
Decide using of digital zoom function.
D-ZOOM : ON/ OFF
Select : or Set ON : Set OFF :
NEAR NEAR
Select : or Set ON : Set OFF :
NEAR NEAR
5. 1. 2 FOCUS MODE
- FOCUS SPD
In Focus menu, you can set up the focus speed, focus mode,
near limit and AF mode.
Set the speed for camera focusing. (0~7 USER)
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
STABILIZER
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ FOCUS MODE >
▷
▷
▷
▷
▷
▷
▷
▷
: USER
: AUTO
: 1M
: NORMAL
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
BACK
▷
< NEAR / RIGHT ▷ FOCUS SPD >
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : OFF
BACK
▷
< NEAR / RIGHT ▷ D-ZOOM >
This manual suits for next models
1
Table of contents
Other Wonwoo Digital Camera manuals


















