WoodLandCut 769839-132 User manual

SAVE THESE INSTRUCTIONS
769839-132 Page 1 of 6
SKU# 287-1498
7.5’ Lighted Flocked Aspen
350 Warm White or Multi Colored LED Lights
with 6 Functions
Item #: 769839-132
SKU # 287-1498
CARTON CONTENTS
Part
Item Description
Quantity
A
Top Section of tree
1
B
Middle Section of tree
1
C
Bottom Section of tree
1
D
Stand for the tree
1
E
Eye Bolts
3
F
Spare Bulbs
6
NOTE - Retain carton for storage purposes
CUSTOMER SERVICE
Prior to assembly, please make sure all carton contents are present. Do not attempt to assemble the tree if any parts are
missing or damaged. Please contact Seasonal Specialties customer service department if you need any assistance or
replacement parts: 1-800-353-3116, 9:00 a.m. –5:00 p.m. CST, Monday –Friday or visit our website at
http://www.seasonalspecialties.com

SAVE THESE INSTRUCTIONS
769839-132 Page 2 of 6
SKU# 287-1498
IMPORTANT SAFETY INSTRUCTIONS
WARNING –Risk of Fire, Personal Injury and Electrical Shock:
1. Read all instructions and warnings included with this tree.
2. Do not assemble or dis-assemble the tree or tree pole while plugged into an electrical outlet, disconnect
plug from all power before starting.
3. Tree sections must be fully inserted. If the sections are not fully inserted, portions of the tree may fall
over. Follow assembly instructions.
4. Keep hands away from the tree connector areas during assembly.
5. Do not alter any connections at the ends of the tree pole and do not attempt to disassemble any parts of
the tree pole, no user serviceable parts are inside.
6. Do not use with cracked or broken connectors or outlets on the tree poles, discard tree.
7. Do not leave product unattended while plugged in.
8. For Indoor Use Only.
9. Do not place near gas or electric heaters, radiators, fireplaces, candles, or other similar sources of heat
or open flames.
10. Place on a level, hard, flat surface: do not place where tree is likely to wobble due to uneven floors or
thick carpeting.
11. After assembling the tree and adding decorations, make sure the tree is stable. If tree is not stable,
shift the weight of the decorations, and use support wires to walls and/or window frames (make sure
they are secure also).
12. Do not use candles on this tree.
13. Do not overload extension cords or power strips, see ratings on those devices and check the rating
label of the product for compatibility.
14. Do not install near fountains, bathtubs, sinks or other areas of standing water.
15. This is an electrical product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children and pets can reach it.
16. Use only the included spare LED bulbs for replacements, and replace only with the same color bulbs.
Do not switch the order of the colors of the bulbs, or switch the color of the bulbs.
17. Replace burnt out bulbs promptly. Leaving burnt out bulbs on the light string will cause additional light
bulbs to burn out early, the more bulbs that are burnt out the quicker the other bulbs will go out,
potentially causing the entire light string to go out very quickly.
18. Do not connect any other light strings or accessories to this tree.
19. Do not use electronic or motorized ornaments that plug into the light sets on this tree as the ornaments
may become permanently damaged if connected to the lights.
20. Use only with the adaptor power supply that was provided with this product.
21. If the adaptor power supply is cracked or broken, do not use product.

SAVE THESE INSTRUCTIONS
769839-132 Page 3 of 6
SKU# 287-1498
ASSEMBLY INSTRUCTIONS
WARNING: Risk of personal injury and electric shock
NOTE: It is normal to see white flocking material in the bottom of the box as some may settle during shipping of the
product and to fall off while handling the tree during assembly or disassembly. This does not affect the appearance
of the product.
a. Watch for and replace any bulbs that may have broken during shipping and storage each year by following the
bulb replacement instructions before assembling or plugging in.
b. Avoid getting white flocking material into eyes, nose, or mouth during handling of the tree, wash hands after
touching and vacuum excess from floor after handling.
1. Carefully remove all pieces from the box and lay out parts flat on the floor. Carefully remove all protective
wrapping from the parts. Before beginning tree assembly please make sure all carton contents are present. A
complete listing and diagram of contents are listed on page 1. Do not attempt to assemble the tree if any parts
are missing or damaged. Please contact our customer service department for replacement parts prior to
returning to store.
2. Take the Tree Stand (D) out and open the legs form an X”.
See Figure 1.
3. Remove the plastic pole protectors from the end of tree sections (B) and (C)
before assembling and discard. See Figure 2.
4. Insert Bottom Section (C) into the assembled Tree Stand (D). Make sure the pole is
firmly inserted into the stand and turn the 3 eye bolt screws so they touch the tree
trunk. Straighten the tree by adjusting the eye bolts in or out and then tighten.
See Figure 3.
5. Locate the female plug from Bottom Section (C) and place it near the top of
the tree section by the center pole. See Figure 4 showing connectors.
6. Insert Middle Section (B) into Bottom Section (C). Connect the male connector from
Middle Section (B) into the female connector from Bottom Section (C). Secure the
connection by tightening the collar on the connectors making sure that the tabs in the
connectors are aligned. See Figure 5.
7. Insert the Top Section (A) into Middle Section (B). Connect the male connector from Top
Section (A) into the female connector from Middle Section (B). Secure the connection by
tightening the collar on the connectors making sure that the tabs in the
connectors are aligned. See Figure 5.
8. The adaptor and the Control Box will come pre-assembled on the tree lights at
the end of Bottom Section (C).
9. Insert the plug blades on the adaptor into an 110V-125V wall receptacle for lights to turn
on. The entire tree should now be lit. If not, press the button on the Control Box to turn
on the lights. Use the Control Box to select the desired light effect. Refer to further
instructions under CONTROL BOX INSTRUCTIONS below.
10. Allow branches to fall into place or gently pull up and out. When adjusting the branches
be sure that all wires are free of branch hinges. Please note that the Top Section (A) does not
have hinges like the Middle Section (B) and Bottom Section (C).
Fig. 1
1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

SAVE THESE INSTRUCTIONS
769839-132 Page 4 of 6
SKU# 287-1498
SHAPING and DECORATING INSTRUCTIONS
STEP 1
Begin to shape the branches by always working from the bottom section of the tree to the top (1a). When working
each section, start with the tips closest to the tree’s center pole (1b). Fan out branch tips, one to the left, one to the
right and one at the center. Tips should be alternately placed so they do not line up one after another (1c). Branch
tips should curve slightly upwards (1d). This will create a more natural looking tree profile. Once a section is
complete, locate next section and repeat same process. Adjust branches between separate tree sections to avoid
leaving any open spaces.
(1a) (1b) (1c) (1d)
STEP 2
When working on the top section, the branch construction is slightly different. Holding the top section, begin to pull
down each layer of branches (2a). Evenly space each row of branches as you work your way towards the top (2b).
Once at the top, locate the top tip of the tree. It will be the longest tip length you will see (2c). Pull this branch
straight up to create your complete tree profile. Place finished section onto the center pole and arrange branches
between sections to create a seamless look.
(2a) (2b) (2c)
STEP 3
Decorate your tree by evenly placing ornaments and other decorations around the tree, making sure to balance the weight
when adding your decorations. After completing, make sure the tree is stable. If tree is not stable, shift the weight of the
decorations, and use support wires to walls and/or window frames (make sure they are secure also) to prevent the tree
from falling over.
CONTROL BOX INSTRUCTIONS
Use the control box to select the desired lighting effect.
1. If lights do not turn on when light cord is plugged into wall receptacle, press the button on control box once to turn on
lights.
2. The control box has the following programmed light functions:
1. Steady Warm White
2. Steady Multi
3. Fading Warm White
4. Fading Multi
5. Slow Alternate (Warm White & Multi Slow Flashing)
6. Fast Alternate (Warm White & Multi Fast Flashing)
7. Off
3. Press the button at the top of the control box to advance the lights to the desired function.
4. Press the button and cycle through all light functions to turn the lights off.

SAVE THESE INSTRUCTIONS
769839-132 Page 5 of 6
SKU# 287-1498
TROUBLESHOOTING INSTRUCTIONS
WARNING:To reduce the risk of electric shock and personal injury.
Before troubleshooting the electrical portion of this product, unplug product from electrical outlet first, and inspect product
carefully:
1) Discard any products that have cut, damaged or frayed wire insulation or cords, cracks in the lampholders or
enclosures, loose connections, or exposed copper wire.
2) Check for and replace any bulbs that are broken, loose, or missing.
With proper care, the LEDs should work for many years, however, as in all products some LEDs may go out early. This
tree is supplied with spare LED bulbs just in case replacement is need, which is done quickly and easily following the
trouble shooting directions below.
Notes:
•Unlike standard sets, it is normal to see some bulbs not working, and still have the other lights in the set still
illuminating; this is one of the ways an LED bulb can go out.
•When replacing bulbs please make sure to line up the bulb locking tab on the bulb with the lampholder, as the
LEDs are polarity (directionally) sensitive, and inserting the bulb backwards may cause a good bulb to go out
and no longer work.
•When replacing bulbs, always use the same color replacement as the bulb you are replacing.
•Promptly replace non-functional, missing or broken bulbs following the bulb replacement instructions in the
safety instructions.
If the Adaptor is Not Connected to the Control Box
1. Locate the male connector at the bottom of tree Section (C) and align matching
tabs on the insides of the connector and the female end of the adaptor. Secure
the connection by tightening the collar on the connectors. See Figure 6.
If Some of the Bulbs Are Not Working:
1. WARNING –Unplug tree from the electrical outlet before troubleshooting. (Refer to the User Servicing Instructions in
the Safety Instruction sheet for exact details on bulb replacement).
2. Check for any bulbs that are installed backwards (bulb locking tabs are on opposite sides of the lampholder and bulb),
remove and replace in correct direction, or replace with one of the supplied spare bulbs making sure the locking tabs
line up.
3. If bulb is not installed backwards and still does not light, it needs to be replaced, remove the bulb and replace only with
one of the supplied replacement bulbs.
WARNING –Only use with the included spare LED bulbs provided with this tree.
NOTE- Bulb shape may not match product.
If a Section of Lights is Not Working:
1. Make sure that all the light string plugs within the tree are securely connected.
2. Check that all the LEDs bulbs are tightly inserted into their lampholders.
3. Check for any missing bulbs.
4. Check for any bulbs that are installed backwards (bulb locking features are on opposite sides of the lampholder and
bulb), remove and replace with one of the supplied spare bulbs of the same color following the bulb replacement
instructions above.
5. Using one of the supplied spare bulbs, start at one end and work your way to the other replacing each bulb that is out
with the spare bulb and continue the process until that section lights. See the bulb replacement directions above.
Please be sure to line up the bulb locking tab on the bulb with the lampholder, as the LEDs are polarity (directionally)
sensitive, and inserting the bulb backwards may cause a good bulb to go out.
Fig. 6

SAVE THESE INSTRUCTIONS
769839-132 Page 6 of 6
SKU# 287-1498
If ALL of the Tree Lights are Off or Not Working:
1. Push the button on the control box to turn on the lights.
2. Make sure the control box connector is securely attached to the adaptor. (See Trouble Shooting Instructions)
3. Make sure the adaptor is plugged into a 110V-125V AC outlet.
4. Make sure the outlet has power (check to see if any switches or timers control the outlet) and not connected to a
dimmer switch.
5. If used on a timer controlled outlet, make sure the timer is rated for use with compact fluorescent bulbs (CFL bulbs) or
LED bulbs, if not, use on a different circuit/outlet.
6. If installed on a GFCI circuit or outlet, reset the GFCI in case it activated.
STORAGE
WARNING: Make sure the tree adaptor is removed from the wall outlet or any other receptacle before starting.
1. Remove all ornaments and decorations from tree.
2. Gently lift off Top Section (A) and disconnect the lights by loosening the collar the two connectors and pulling the
female plug from the male plug, then lift off Middle Section (B) and repeat same steps to disconnect the two
connectors, and finally remove the Bottom Section (C) from the tree stand.
3. Carefully place the tree and stand in its carton and tape shut.
DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100° F.
FLAME RETARDANT
1YearLimitedWarranty -Subject totheexclusionscontainedbelow,SeasonalSpecialtiesLLC,atitsoption,willatnochargerepair,
replace (with sameorequivalentproduct),orrefund the purchase price if this product fails to light due to defects in material
or workmanship within three (1) year from the date of purchase . To obtain _ service, ship the product prepaid
along with the Original UPC & Original dated legible proof of purchase to Seasonal Specialties, L.L.C., 11455 Valley
View Road, Eden Prairie, MN 55344, Attn: Customer Service. Allow six to eight weeks for handling. We are
committed to making high quality products. Returning the product to us helps us to monitor and improve product
quality.
Exclusions - This product is intended for residential seasonal use only (90 days maximum per year), and was
pre-tested and date coded prior to shipment. This limited warranty extends only to the first consumer
purchaser, and is not transferable. This warranty does not include: 1) commercial use, 2) normal wear and
tear, 3) products not used in accordance with directions provided on or with the product, 4) burnout of bulbs or
LEDs, 5) batteries, 6) products that have been subjected to unauthorized repair, and/or modification, or 7)
damage caused by shipping, improper handling, alterations, misuse, or accidents.
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND
AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO
EVENT SHALL SEASONAL SPECIALTIES, LLC BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, ARISING OUT OF OR IN CONNECTION WITH THE USE OF THE PRODUCT TO THE FULL
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages,
or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights that vary from state to
state or from one jurisdiction to another.
When shipping product back to us, please include your return address, contact phone, and e-mail address in
addition to the other requested information. Please contact us at 1-800-353-3116 or visit our website at
www.seasonalspecialties.com for additional information.