Worcester GB162-50 User manual

UK/IE
Operating Instructions
Wall hung gas fired condensing boiler
Worcester Commercial Boiler Series
GB162-50/65/85/100 V2
6720814332-0.1TD
For central heating systems and indirect fed domestic hot water
6720814333 (2018/04) UK/IE
If you smell gas:
▶ Well away from the building: In Great Britain call the National
Gas Emergency Service on 0800 111 999.
In Northern Ireland call 0800 002 001 and in Ireland call
1850 20 50 50
▶L.P.G. boilers: Call the supplier’s number on the side of the
gas tank.
These appliances are for use with Natural Gas or L.P.G.
(Cat. II2H3P type C13, C33 & C53)
Model GC Number
Natural Gas 50 kW 41-406-66
65 kW 41-406-67

Key to symbols and safety instructions
6720814333 (2018/04)2
Table of Contents
1 Key to symbols and safety instructions . . . . . . . . . . . . . . . . . . . 2
1.1 Key to symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Appliance types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Energy efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Operating the boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Overview of components . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2 Opening the gas isolation valve . . . . . . . . . . . . . . . . . . . . 5
3.3 Opening service valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.4 Switch on the boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.5 Check water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.6 Setting the maximum boiler temperature . . . . . . . . . . . . 5
3.7 Heating controller settings . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Operating the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 Information menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.3 Anti-Freeze Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.4 Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5 Inspection and servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Refilling the heating system . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 Cleaning the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.1 Standard shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.2 Shutting down when there is a risk of frost . . . . . . . . . . . 8
7 Display information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.1 Display codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.2 A fault has occurred but no fault code is displayed . . . . . 9
8 Energy saving and environmental protection . . . . . . . . . . . . . . 9
8.1 Energy savings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.2 Environment / disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1 Key to symbols and safety instructions
1.1 Key to symbols
Warnings
The following keywords are defined and can be used in this document:
•NOTICE indicates a situation that could result in damage to property
or equipment.
•CAUTION indicates a situation that could result in minor to medium
injury.
•WARNING indicates a situation that could result in severe injury or
death.
•DANGER indicates a situation that will result in severe injury or
death.
Important information
Additional symbols
1.2 General safety instructions
Instructions for the target group
These operating instructions are intended for the heating system user.
All instructions must be observed. Failure to comply with instructions
may result in material damage and personal injury, including possible
loss of life.
▶ Read and retain the operating instructions (heat source, heating
controller, etc.) prior to operation.
▶ Observe safety instructions and warnings.
If you smell gas
A gas leak could potentially cause an explosion. If you smell gas, observe
the following rules.
▶ Avoid producing flames or sparks:
– Do not smoke, do not use a lighter or strike matches.
– Do not operate any electrical switches or unplug any equipment.
– Do not use the telephone or ring doorbells.
▶ Turn off the gas supply at the main shut-off valve or at the gas meter.
▶ Open windows and doors.
▶ Warn your neighbours and leave the building.
▶ Prevent anyone from entering the building.
▶ Stay well away from the building: call the emergency services and the
gas supplier.
Warnings in this document are identified by a warning
triangle printed against a grey background.
Keywords at the start of a warning indicate the type and
seriousness of the ensuing risk if measures to prevent
the risk are not taken.
This symbol indicates important information where
there is no risk to people or property.
Symbol Explanation
▶ Step in an action sequence
Cross-reference to another part of the document
• List entry
– List entry (second level)
Table 1

Product information
6720814333 (2018/04) 3
Correct use
The wall hung gas fired condensing boiler may only be used in sealed
heating systems for central heating and Domestic Hot Water.
Any other use is not permitted. We assume no responsibility for damage
caused by incorrect use.
Inspection and servicing
If there is a lack of cleaning, inspection or maintenance, or if these are
carried out incorrectly, this may result in material damage and/or
personal injury, including possible loss of life.
▶ Have work carried out only by an approved installer.
▶ Have any defects rectified immediately.
▶ Have the heating system inspected once a year by an approved Gas
Safe registered contractor, and have any required maintenance or
cleaning work carried out.
▶ We recommend that you enter into a contract covering an annual
inspection and needs-based maintenance with an approved
contractor.
Conversion and repairs
Modifications to the heat source or other parts of the heating system can
result in personal injury and/or material damage.
▶ Have work carried out by an approved Gas Safe contractor only.
▶ Never remove the casing of the heat source.
▶ Never carry out any modifications to the heat source or to other parts
of the heating system.
▶ Never close, block or obstruct the outlet of the pressure relief valves.
Heating systems with DHW cylinder: During heat-up, water can
escape from the pressure relief valve of the DHW cylinder.
Open flue operation
The installation location must be adequately ventilated, if the heat
source draws its combustion air from the room.
▶ Never cover or reduce the size of ventilation apertures in doors,
windows and walls.
▶ Consult a contractor to ensure that ventilation requirements are met:
– if structural modifications are made (e.g. replacing windows and
doors)
– if appliances with an air discharge outside are subsequently
installed (e.g. extractor fans, kitchen fans or air conditioning
units).
Condensate pipe work
Condensate is produced in this boiler and removed via a condensate
pipe to a drain. Modification or blocking of the condensate pipe work is
not permitted.
Combustion air/ambient air
The air in the installation room must be free of combustible or chemically
aggressive substances.
▶ Do not use or store combustible or explosive materials (paper,
propellants, thinners, paints, etc.) within the vicinity of the
appliance.
▶ Do not use or store corrosive substances (solvents, adhesives,
chlorinated cleaning agents, etc.) within the vicinity of the appliance.
Appliance operation
This appliance can beused by children agedfrom 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, if they have been given supervision or
instruction concerning the use of the appliance, in a safe way, and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without
supervision.
2 Product information
2.1 Declaration of Conformity
2.2 Appliance types
This document refers to the following appliance types:
• GB162-50 V2
• GB162-65 V2
• GB162-85 V2
• GB162-100 V2
The designation of the boiler comprises the following:
• Worcester: manufacturer
• GB162 V2: product name
• 50, 65, 85 or 100: type name (output)
The design and operating characteristics of this product
comply with the European and national requirements.
The CE marking declares that the product complies with
all the applicable EU legislation, which is stipulated by
attaching this marking.
The complete text of the Declaration of Conformity is
available on the Internet (à address on the back cover of
these instructions).

Product information
6720814333 (2018/04)4
2.3 Energy efficiency
The following product data satisfy the requirements of the EU Regulations No. 811/2013, No. 812/2013, No. 813/2013 and No. 814/2013
supplementing Directive 2010/30/EU.
Product data Symbol Unit 50-V2 65-V2 85-V2 100-V2
Product type – – GB162-50 V2
G20
GB162-65 V2
G20
GB162-85 V2
G20
GB162-100 V2
G20
Condensing boiler – – 
Low temperature boiler – – 
B1 boiler – – 
Cogeneration space heater (CHP) – – 
Combination heater – – 
Rated heat output Prated kW 47 63 80 95
Seasonal space heating energy efficiency ηs%93 92 – –
Energy efficiency class – –A A– –
Useful heat output
At rated heat output and high temperature regime 1)
1) High-temperature regime is defined as 60 °C return temperature at heater inlet and 80 °C feed temperature at heater outlet.
P4kW 46.5 62.6 80.0 94.5
At 30 % of rated heat output and low temperature regime 2)
2) Low temperature for condensing boilers is defined as 30 °C, for low-temperature boilers 37 °C and for other heaters 50 °C return temperature (at heater inlet).
P1kW 15.4 20.8 26.5 31.2
Useful efficiency
At rated heat output and high temperature regime 1) η4% 88.0 87.7 87.3 87.4
At 30 % of rated heat output and low temperature regime 2) η1% 97.4 97.1 97.2 97.2
Auxiliary electricity consumption
At full load elmax kW 0.041 0.082 0.100 0.100
At part load elmin kW 0.018 0.018 0.024 0.024
In standby mode PSB kW 0.006 0.006 0.006 0.006
Other items
Standby heat loss Pstby kW 0.088 0.088 0.088 0.088
Ignition burner power consumption Pign kW 0.000 0.000 0.000 0.000
Emissions of nitrogen oxides NOx mg/kWh 15 24 21 35
Sound power level, indoors LWA dB(A) 54 61 – –
Table 2 Product data for energy consumption

Operating the boiler
6720814333 (2018/04) 5
3 Operating the boiler
3.1 Overview of components
Fig. 1 Overview of components
[1] Control panel
[2] Pump
[3] Hydraulic isolation valves with temperature gauges
[4] Gas isolation valve
[5] Pressure gauge
3.2 Opening the gas isolation valve
▶ Push the gas isolation valve in and turn anti-clockwise until the valve
lines up with the gas line.
Fig. 2 Opening the gas isolation valve
3.3 Opening service valves
▶ Open both service valves so that the tap lines up with pipework.
Fig. 3 Opening service valves
3.4 Switch on the boiler
▶ Put the on/off switch to position “1” (figure 5, [1]).
3.5 Check water pressure
For the boiler to work efficiently, the normal water pressure must be
between 1.0 and 2.0 bar.
▶ Ask the installer whether a higher pressure is necessary.
▶ Read off the water pressure on the display (Chapter 4.1, page 6).
▶ Top up the heating system if necessary (Chapter 5.1, page 8).
Fig. 4 Read off the water pressure
3.6 Setting the maximum boiler temperature
▶ Set the maximum boiler temperature required in the setup menu
(Chapter 4.2).
3.7 Heating controller settings
Some of the functions described in this document change when
connecting a heating controller, i.e. room thermostat or weather-
compensated controls. The controls exchange parameters with the
boiler.
▶ You should therefore carefully read the operating instructions for the
corresponding heating controls.
6720814333-01.1TD
4 353
2
1
6720814333-02.1TD
The heating and DHW operations can be switched on and
off independently of one another.
6720814333-03.1TD
6720813683-1.1TD

Operating the appliance
6720814333 (2018/04)6
4 Operating the appliance
Fig. 5 Control panel
[1] On/off switch
[2] Reset key
[3] Chimney sweep key
[4] Help key
[5] Display
[6] Menu key
[7] Down key
[8] Up key
[9] Diagnostic plug
[10] Burner LED
The front of the boiler contains a control panel with the following
elements:
On/off switch
The boiler can be switched on or off via the on/off switch. The power
supply is not interrupted.
Reset ckey
The boiler can be restarted via the c key in the event of blocking faults
(Chapter 7 “Display information”).
Chimney sweep dkey
The boiler can be brought into operation via the dkey in order to carry
out measurements. Used for servicing.
Info Lkey
The boiler status can be read out via the Lkey.
Display
Display values, settings and codes can be read off the display. If the
boiler is switched on via the mains isolator, all symbols appear briefly in
the display.
Menu O key
To change the settings, open the menu via the Okey.
Down Nand up Mkeys
You can navigate the various menus via the arrow keys. Press an arrow
key to change a setting or value.
Diagnostic plug
An external diagnostic tool can be connected here.
Burner LED
The Burner LED lights up when the burner is firing.
4.1 Information menu
Information on the statusof the boiler can be read out via the information
menu. Proceed as follows:
▶ Press Lto open the information menu.
▶ Navigate the menu with Mand Nkeys in order to read out the
required data.
▶ Press Lto exit the information menu.
Status display
Display when the boiler is switched on (approx. 1 second)
20.0 Current flow temperature [°C]
p2.0 Operating pressure [bar]
(display flashes if the operating
pressure is too low)
CChimney sweep mode (service
operation)
BBurner in operation
RCentral heating
SDHW
IPump running
TOutside temperature display
An interlocking fault has occurred or
the boiler requires a service.
Table 3 Readings on the display
6720813419-4.1TD
1 3 5 104 986 72
After a few minutes of inactivity, the menu closes
automatically and the home screen is displayed.
Information menu
“info” is displayed for 1 second.
Maximum boiler flow temperature set [°C]
during heating mode and chimney sweep
mode.
“OFF” appears in the display when heating
mode is switched off.
No information about DHW mode is shown
here.
Display of service code.
This information is only displayed if the boiler
requires a service intervention.
For a comprehensive overview of the display
codes and corresponding explanations see
Chapter 7.
Displays an operating code or fault code.
For a comprehensive overview of the display
codes and corresponding explanations see
Chapter 7.
Current operating pressure [bar].
Current boiler flow temperature [ºC].
Outside temperature [ºC].
Only displayed with weather-compensated
control.
Calculated boiler flow temperature (setpoint)
[ºC] during heating mode R.
Table 4 Information menu

Operating the appliance
6720814333 (2018/04) 7
4.2 Setup menu
The boiler settings can be displayed and modified via the setup menu.
Proceed as follows:
▶PressOto open the setup menu.
▶ Navigate the menu with Mand Nkeys.
▶PressandholdOto access a setting. Once the settingflashes it can
be modified.
▶ Change the setting via Mand Nkeys.
▶Press
Oto save the setting. The setting no longer flashes.
The display values shown are the default settings.
4.3 Anti-Freeze Protection
Parts of the line may freeze during the cold season. Water permanently
flows through the heating system which significantly reduces the
probability of freezing.
▶ Check whether all radiator valves are open.
▶ Press Oto open the setup menu.
▶ Set the pump over-run time to 24 hours (Chapter 4.2).
If the boiler is switched off, see Chapter 6.2.
4.4 Key lock
The setup menu can be locked to prevent the settings from being
changed by unauthorised personnel. Proceed as follows:
Activation
▶ Press the Mand Nkeys simultaneously for 5 seconds.
The word “Lock” is displayed for 5 seconds. The information menu
remains readable.
Fig. 6 Display - Lock
Disable
▶ Press the Mand Nkeys again simultaneously for 5 seconds to
remove the key block; the word “Lock” disappears.
Current ionisation current [μA].
Current burner output [%] during heating
mode R. Mod = modulation
Current pump speed [%].
Mod = modulation
Setup menu
“menu” is displayed for 1 second.
Heating mode is switched on.
Setting: On, Off.
▶ Set the maximum boiler flow temperature
based on the heating system type.
Adjustment range: 30 - 90 °C.
Examples of settings:
• 40 °C underfloor heating system
• 75 - 85 °C radiators
• 85 - 90 °C convectors
▶ Set the maximum output of the heating
system.
The output is displayed in % when modifying
the setting.
Adjustment range: 0 - 100%.
No information about DHW mode is shown
here.
▶ Change the minimum pump speed if
required.
Adjustment range:
30 % - max. (setting max. parameter).
▶ Increase the minimum pump speed if parts
of the heating system do not become hot
enough.
Table 5 Setup menu
Information menu
Table 4 Information menu
▶ Change the maximum pump speed if
required.
Adjustment range
min. (setting min. parameter):
• 50-V2 - 57%
• 65-V2 - 65%
• 85-V2 - 65%
• 100-V2 - 83%
▶ Reduce the maximum pump speed if
aggravating flow noises can be heard.
Pump over-run time following end of heating
demand [Min].
Adjustment range: 1 - 60 min./24 hours.
Setup menu
Table 5 Setup menu
6 720 614 523-133.2TD

Inspection and servicing
6720814333 (2018/04)8
5 Inspection and servicing
The user is responsible for ensuring the general safety and annual
servicing of the heating system.
Recommendations:
▶ To ensure the boiler functions correctly, maintenance should be
carried out annually by a certified installer.
▶ To do this, organise a maintenance and inspection contract.
5.1 Refilling the heating system
Every heating system is refilled with heating water in different ways,
depending on the water quality.
▶ You should therefore ask the installer to explain the refilling process
to you at system handover.
▶ If persistent refilling is required then please contact a qualified
contractor, it is likely that a leak exists
5.2 Cleaning the casing
▶ Only clean the casing of the boiler with a damp cloth and possibly a
mild detergent.
6Shutdown
6.1 Standard shutdown
▶ Put on/off switch in position “0”.
▶ Close the gas isolation valve under the boiler (figure 2).
6.2 Shutting down when there is a risk of frost
If the boiler stays on:
▶ Set the pump over-run time to 24 hours (Chapter 4.2).
▶ Make sure that sufficient flow to all radiators is possible.
If the boiler is switched off:
▶ Put on/off switch in position “0”.
▶ Close the gas isolation valve under the boiler.
▶ Drain the entire heating system.
7 Display information
7.1 Display codes
A display code provides information about the status of the boiler. Fault
codes are either shown in the display directly or can be called up via the
information menu. Proceed as follows:
▶ Navigate the menu to the fault code level. Press Land toggle with
Mand N.
▶ Identify the fault code and search for the corresponding explanation
(table 6).
▶ Implement the solution to eliminate the fault.
There are 3 types of code:
• normal operating code
• blocking fault code
• interlocking fault code
For safety reasons, the boiler shuts down and locks as soon as a fault
occurs. This is indicated by an illuminated fault code. The boiler must be
reset in order to unlock it. Proceed as follows:
▶Hold
cpressed down until “rE ” appears in the display.
In most cases, the boiler will work again normally following the reset.
If the fault code still persists contact your installer, stating the appliance
type and fault code. Alternatively please contact Worcester Technical
Support (contact details on the back cover of this guide).
Code Explanation Corrective measure
- - 2 0 0 The boiler is in heating
mode.
- - 2 0 1 The boiler is in DHW
mode.
- - 2 0 2 The boiler cannot
transfer the heat to the
heating system.
•Checkwhethera
sufficient number of
radiator valves are open.
•Bleedradiators/
heating system.
• Reset the boiler.
- - 2 0 3 The boiler is in standby
mode, there is no heat
demand.
- - 2 0 4 The boiler cannot
transfer the heat to the
heating system.
- - 2 1 2 The sensors inside the
boiler detected
unexpected
temperatures.
•Checkwhethera
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
- - 2 6 0
- - 2 6 5 The boiler is waiting.
The boiler duly switches
on in order to satisfy the
heat demand.
- - 2 7 0 The boiler starts.
- - 2 8 3
- - 2 8 4
C E 2 0 7 The water pressure is
too low.
• Check the water
pressure of the boiler
and top up if necessary.
• Reset the boiler.
C E 2 6 6 The sensors inside the
boiler detected
unexpected
temperatures.
• Check the water
pressure of the boiler
and top up if necessary.
•Checkwhethera
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
d 4 2 1 3 The sensors inside the
boiler detected
unexpected
temperatures.
•Checkwhethera
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
d 4 3 4 1
E 9 2 1 9 The sensors inside the
boiler detected
unexpected
temperatures.
•Checkwhethera
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
E 9 2 2 0
Table 6 Operating and fault codes

Energy saving and environmental protection
6720814333 (2018/04) 9
7.2 A fault has occurred but no fault code is displayed
It is possible that even though a fault code is not displayed the boiler
does not operate according to your expectations. You should then check
the following:
Heating system does not heat up.
▶ Check in the information menu whether a fault code is displayed and
try to remedy the fault.
▶ Check the set boiler temperature in the setup menu.
▶ Check the settings of the heating controller by referring to its manual.
If the fault code still persists contact your installer.
▶ Note the fault code.
▶ State the appliance type and serial number. These are listed on the
right-hand side of the boiler.
Fig. 7 Right-hand side of the boiler
[1] Serial number
[2] Device type
8 Energy saving and environmental protection
8.1 Energy savings
Efficiency optimised
The boiler has been designed to keep gas consumption and
environmental pollution to a minimum and to maximise comfort.
The gas supply to the burner is controlled according to the heat demand
of the heating system.
The boiler operates with a “modulating control.” This control adjusts the
gas consumption in relation to the existing heat energy demand. The
modulating control reduces temperature fluctuations so the heat is
distributed evenly in the rooms.
The modulating control enables the boiler to still use less gas when
burning continuouslythan a boiler which is continuously being switched
on and off.
Underfloor heating system
▶ Never set the flow temperature higher than the maximum flow
temperature recommended by the installer.
Living space ventilation
Do not ventilate by leaving the windows slightly open. This draws heat
continuouslyfrom the room without significantly improving the quality of
the room air.
▶ Ventilate the room intermittently. Close the doors of the room to be
ventilated.
▶ Turn down the thermostatic valves of the radiator(s) in the room
when ventilating it.
8.2 Environment / disposal
Environmental protection is a fundamental corporate strategy of the
Bosch Group.
The quality of our products, their efficiency and environmental safety
are all of equal importance to us and all environmental protection
legislation and regulations are strictly observed.
We use the best possible technology and materials for protecting the
environment taking into account of cost-effectiveness.
Packaging
We participate in the recycling programmes of the countries in which our
products are sold to ensure optimum recycling.
All of our packaging materials are environmentally friendly and can be
recycled.
Old appliance
Old appliances contain recyclable materials.
The assemblies are easily separated and the types of plastic are clearly
marked. In this way the individual components can be easily sorted and
directed to recycling or disposal.
E 9 2 2 4 The temperature
measured by a
thermostat in the boiler
is too high.
• Check the water
pressure of the boiler
and top up if necessary.
• Check whether a
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
E A 2 2 7 No burner ignition. • Check that the gas
isolator is open.
• Reset the boiler.
E 9 2 7 6 The temperature
measured by the
sensors in the boiler is
too high.
• Check the water
pressure of the boiler
and top up if necessary.
• Check whether a
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
E 9 2 8 5
E F 3 4 5 The sensors inside the
boiler detected
unexpected
temperatures.
• Check whether a
sufficient number of
radiator valves are open.
• Bleed radiators and vent
heating system.
• Reset the boiler.
F d 2 3 1 The power was briefly
interrupted during a
fault.
• Reset the boiler.
H 0 7 The water pressure is
too low.
• Check the water
pressure of the boiler
and top up if necessary.
r E The boiler is reset.
Code Explanation Corrective measure
Table 6 Operating and fault codes
6720813683-2.1TD
2
1

6720814333 (2018/04)10
Notes

6720814333 (2018/04) 11
Notes

Worcester, Bosch Group
Cotswold Way, Warndon, Worcester WR4 9SW.
Tel. [phone]
Worcester, Bosch Group is a brand name of Bosch Thermotechnology Ltd.
worcester-bosch.co.uk
6720814333
WORCESTER, BOSCH GROUP:
TECHNICAL SUPPORT: 0330 123 3366
APPOINTMENTS: 0330 123 9339
SPARES: 0330 123 9779
LITERATURE: 0330 123 9119
TRAINING: 0330 123 0166
SALES: 0330 123 9669