WorkPro W082095AE User manual
W082095AE
SAVE THIS MANUAL FOR FUTURE REFERENCE
Distributed by:
Hangzhou GreatStar Industrial Co., Ltd.
No.35 Jiuhuan Road, Jiubao Town,
Hangzhou 310019, China
www.greatstartools.com
MADE IN CHINA
OPERATOR'S MANUAL
4 - TIER METAL WIRE SHELVING UNIT
23.6" W x14" D x47" H
USE PRECAUTION
For your safety
INSTRUCTION
MANUAL
Read and understand
EYE PROTECTION
Must be worn
PROTECTIVE GLOVES
Must be worn when
assembly
CAUTION: Read and follow all Safety Rules and Operating instructions before first use of this product.
NOTE: Ensure all components are present. If any components are missing, do not proceed with
WORKPRO
2
TABLE OF CONTENTS
Safety Information -------------------------------------------------------------------------
Specifications ------------------------------------------------------------------------------
Package Contents -------------------------------------------------------------------------
Assembly -----------------------------------------------------------------------------------
Cleaning and Maintenance ----------------------------------------------------------------
Customer Service --------------------------------------------------------------------------
2
2
3
4-8
8
8
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USE.
Handle with care.
For ease and efficiency, the product should be assembled by two adults.
Regularly check if all screw connections are tight and if all shelves are attached in a stable way.
To avoid scratching the floor, assemble the shelving unit on a soft surface such as a carpet.
Load the unit evenly and place the heaviest items on the lower shelves.
SAFETY INFORMATION
WARNING!
SPECIFICATIONS
Maximum load of Shelving unit
Maximum load of One single shelf
600 lbs.
150 lbs.
DO NOT let children climb on or play with the unit.
Make sure not to drill into water or electricity lines when securing the shelving unit to the wall. Use
a wire tracer and/or a water pipe finder (not included) if necessary.
WORKPRO
Ensure all components are present. If any components are missing, do not proceed with assembly. Please send
3
PACKAGE CONTENTS
TOOLS REQUIRED
(NOT INCLUDED):
Rubber Mallet
Protective Gloves
A
G
B
C
D
F
E
# #
Shelf x 4
Top Post (with Post
Cap Preassembled) x 4
Bottom Post x 4
Foot Leveler x 4
S Hook x 4
Threaded Post Jointer
(Preassembled on
the Top Post ) x 4
Plastic Sleeve x 16
DESCRIPTION DESCRIPTION
A
B
C
D
E
F
#
G
WORKPRO
4
ASSEMBLY
NOTE:
Discard the black plastic spacers. These are used to separate the shelves for shipping purposes.
Assemble on a flat surface. A piece of cardboard is recommended to keep the product from being
scratched during assembly.
Two people are recommended for assembly.
Screw four foot levelers (D) clockwise into the bottom of four bottom posts (C).
STEP 1: FOOT LEVELER ASSEMBLY
PART
DESCRIPTION
QTY
C
Bottom Post
Bottom Post
4
D
Foot Leveler
Foot Leveler
4
Fig. 1
C
D
WORKPRO
5
ASSEMBLY
PART
DESCRIPTION
C FA
QTY
Plastic Sleeves
Plastic
Sleeves
Plastic Sleeves
Shelf
Shelf
Shelf
Bottom Post
Bottom Post
4 82
Attach four plastic sleeves (F) to the appropriate bottom posts (C) one in each post. Ensure the arrows
on the plastic sleeves should point upwards. The plastic sleeves must be at the same height for each
post to ensure the shelf sits on the sleeves levelly.
Slide the first shelf (A) down from the top of the posts and onto the plastic sleeves (F). Push down on
each corner of the shelf, ensuring that the shelf is in the fully locked position.
Repeat for the second shelf (A).
STEP 2: FIRST AND SECOND SHELF ASSEMBLY
Fig. 2
Fig. 3
C
Bottom Post
C
F
ARROW
A
A
F
WORKPRO
6
ASSEMBLY
PART
DESCRIPTION
QTY
B
Top Post
Top Post
4
C
Bottom Post
Bottom Post
4
Screw four top posts (B) into four bottom posts(C) tightly together clockwise.
STEP 3: TOP POST ASSEMBLY
Fig. 4
B
C
B
C
WORKPRO
7
ASSEMBLY
Repeat the step 2 to install the third and fourth.
Place cardboard over the corners of each shelf and gently tap down with a rubber mallet (or similar tool)
until the shelf is level.
STEP 4: THIRD AND FOURTH SHELVES ASSEMBLY
Fig. 5
PART
DESCRIPTION
FA
QTY
Plastic Sleeves
Plastic Sleeves
Shelf
82
Shelf
A
F
WORKPRO
8
Wipe with a dry cloth as needed to remove dust and dirt.
Avoid contact with corrosive substances like acids, alkaline or similar substances.
CLEANING AND MAINTENANCE
If you are having difficulty in using this product and require support, please send an email to
CUSTOMER SERVICE
ASSEMBLY
Place four S hooks (G) on the shelves at your desired position as you need.
STEP 5: S HOOK ASSEMBLY
Fig. 6
PART
DESCRIPTION
G
QTY
S Hook
S Hook
4
G
WORKPRO
Table of contents
Other WorkPro Rack & Stand manuals
