Worldlawn WY28T User manual

R
WY28T Lawn Mower
Operator’s Manual
Worldlawn Power Equipment, Inc.
Industrial Park 2415 Ashland Ave. Beatrice, NE 68310
Toll Free Number: 1-800-267-4255
●
Safety Information
●
Adjustments & Repairs
●
Accessory

OPERATOR’S MANUAL
This manual contains assembly, operating, maintenance, adjustment, and safety instructions for your WY28T
lawnmower.
Before operating your mower, read this manual in its entirety carefully.
By following the operating, maintenance, adjustment, and safety instructions, you will prolong the life of your
mower, maintain its maximum efficiency, and promote safe operation.
Keep this mower Owner’s Manual when lent or transferred.
If this mower Operator’s Manual becomes lost, damaged, or illegible, replace it immediately; replacements may
be downloaded from our website (www.worldlawnpowerequipment.com) or ordered from our sales department.
If additional information is needed, contact our sales department or a dealer. Always be ready to provide the
model number and serial number.
POTENTIAL HAZARD
· This product is a piece of power equipment.
WHAT CAN HAPPEN
· Failure to follow safe operating practices can result in serious operator injury or even death.
HOW TO AVOID THE HAZARD
· Keep all shields, guards, and safety devices (especially the grass discharge system) in place and
in proper working condition.
· Stop machine and wait for all moving parts to stop, remove spark plug wires or remove key
before adjusting, servicing, or performing maintenance.
· If mower deck becomes clogged, stop machine and wait for all moving parts to stop. Remove
spark plug wire or remove key before cleaning blockage.
· Keep hands, feet, and clothing away from power driven parts.
· Keep others off mower.
POTENTIAL HAZARD
· Gasoline is harmful or fatal if swallowed. Long-term exposure of vapor causes cancer in
laboratory animals.
WHAT CAN HAPPEN
· Failure to use caution may cause serious injury or illness.
HOW TO AVOID THE HAZARD
· Avoid prolonged breathing of vapor.
· Keep face away from nozzle and gas tank opening.
· Keep away from eyes and skin.
· Never siphon by mouth.

3
TABLE OF CONTENTS
1. SAFETY…………………………………………………………………………………...
5
1.1 SafetyAlert Symbol ………………………………………………………………………..
5
1.2 Training …………………………………………………………………………………..
5
1.3 Preparation ………………………………………………………………………………..
5
1.4 Operation ………………………………………………………………………………....
7
1.5 Maintenance & Storage ………………………………………………………………….....
10
1.6 Safety Decals …………………………………………………………………………. . . .
10
2. SPECIFICATIONS……………..…………………………………………………………..
13
2.1 Model Number …………………………………………………………………………….
13
2.2 Engine …………………………………………………………………………………....
13
2.3 Frame Assembly……………………………………………………………………………
13
2.4 Drive System ……………………………………………………………………………...
13
2.5 Cutting Deck………………………………………………………………………………
13
2.6 Operator Controls………………………………………………………………………….
13
2.7 Accessories …………………………………………………………………………….....
14
2.8 Approximate Dimensions …………………………………………………………………..
14
2.9 Torque Requirements ………………………………………………………………………
15
3. ASSEMBLY INSTRUCTIONS ……………………………………………………………..
15
3.1 Open Crate ………………………………………………………………………………..
15
3.2 Initial Instructions …………………………………………………………………………
15
3.3 Service Engine …………………………………………………………………………….
15
4. OPERATION INSTRUCTIONS……………………………………………………………………..
16
4.1 Pre-start …………………………………………………………………………………..
16
4.2 Starting Engine …………………………………………………………………………....
17
4.3 Mowing …………………………………………………………………………………..
17
4.4 Moving Operation …………………………………………………………………………
17
4.5 Stopping Engine …………………………………………………………………………...
17
5. MAINTENANCE &ADJUSTMENTS……………………………………………………………...
18
5.1 Periodic Maintenance ………………………………………………………………………
18
5.1.1 Check the Engine Oil Level ………………………………………………………………
18
5.1.2 Clean EngineAir Cooling System………………………………………………………….
18
5.1.3 Clean Grass Build-up from Under Deck……………………………………………………
19
5.1.4 Check Mower Blades……………………………………………………………………..
19
5.1.5 Check Safety Interlock System ……………………………………………………………
20

4
5.1.6 Check for Loose Hardware ………………………………………………………………
20
5.1.7 Service Air Cleaner……………………………………………………………………….
20
5.1.8 Change Engine Oil………………………………………………………………………..
20
5.1.9 Check Tire Pressure………………………………………………………………………
21
5.1.10 Check Condition of Belts ………………………………………………………………..
21
5.1.11 Lubricate Grease Fittings ………………………………………………………………..
21
5.2 Adjustments ……………………………………………………………………………….
22
6. TROUBLESHOOTING…………………………………………………………………….
26
7. SERVICE BATTERY ……………………………………………………………………...
27
7.1 Check Battery…………………………………………………………………………...
28
7.2 Connecting the Negative Battery Cables…………………………………………………..
28
7.3 Maintenance Period ……………………………………………………………………..
29
8. ELECTRICALDIAGRAM ………………………………………………………………………….
30
9. LIMITED WARRANTY……………………………………………………………………………...
31

5
1. SAFETY
1.1 SAFETYALERT SYMBOL
This SAFETY ALERT SYMBOL is used both in this manual and on the machine to identify important safety
messages which must be followed to avoid accidents. This symbol means:
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
The safety alert symbol above alerts you to unsafe actions or situations by the word DANGER,
WARNING, or CAUTION.
White letters on red background.
Failure to observe the safety instructions could result in death or serious injury.
Black letters on orange background. Failure to observe the safety instructions could result in death or
serious injury.
Black letters on yellow background.
Failure to observe the safety instructions may result in slight or serious injury.
1.2 TRAINING
1.2.1 Regard the mower as a piece of power equipment. The operator needs to be trained before operating this unit.
1.2.2 Read the instructions carefully. Be thoroughly familiar with controls and the proper use of the
equipment.
1.2.3 Never allow children, teenagers, or adults to operate the equipment without proper instruction.
1.2.4 Keep everyone, especially children and pets, away from the area of operation. Remember that the operator or
user is responsible for accidents or hazards occurring to other people or their property.
1.3 PREPARATION
1.3.1 Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform
the job. Only use accessories and attachments approved by
Worldlawn Power Equipment, Inc.
1.3.2 The use of personal protective equipment, such as (but not limited to) protection for the eyes, ears, feet, and
head is recommended.
POTENTIAL HAZARD
· This machine produces sound levels in excess of 85dBA at the operator’s ear when in operation.
WHAT CAN HAPPEN
· Exposure to sound levels of 85dBA or above for extended periods of time can cause hearing loss.
HOW TO AVOID THE HAZARD
· Wear hearing protection when operating this machine.
1.3.3 While mowing, always wear ample footwear and long trousers. Do not operate equipment when barefoot or
when wearing open sandals.
1.3.4 Thoroughly inspect the area where the equipment is to be used and remove all stones, sticks, wires, bones, and
other foreign objects which may damage the equipment or cause personal injury to operator or bystanders.

6
POTENTIAL HAZARD
· Engine exhaust contains carbon monoxide, which is an odorless deadly poison.
WHAT CAN HAPPEN
· Carbon monoxide can kill you.
HOW TO AVOID THE HAZARD
· Do not run engine indoors or in a small confined area where dangerous carbon monoxide fumes can collect.
POTENTIAL HAZARD
· In certain conditions gasoline is extremely flammable and highly explosive.
WHAT CAN HAPPEN
· A fire or explosion from gasoline can burn you, others, and cause property damage.
HOW TO AVOID THE HAZARD
· Do not smoke while refueling, and stay away from an open flame or where gasoline fumes may be ignited by a
spark.
· Refuel only outdoors.
· Store gasoline in an approved container and keep it out of the reach of children.
· Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel when engine is running
or when the engine is hot.
· Never fill the fuel tank so that gasoline level rises above a level that is 3/8"(10mm) below the bottom of the
filler neck to allow for gasoline expansion and prevent fuel spillage.
· If fuel is spilled, DO NOT attempt to start the engine. Move away from the area of the spill and avoid creating
any source of ignition of the fuel until vapors have dissipated.
· Do not operate without entire exhaust system in place and in proper working condition.

7
POTENTIAL HAZARD
· In certain conditions gasoline is extremely flammable and highly explosive.
WHAT CAN HAPPEN
· A static charge can ignite gasoline vapors. A fire or explosion from gasoline can burn you, others, and cause
property damage.
HOW TO AVOID THE HAZARD
· Purchase and store gasoline only in an approved container.
· Always place gasoline containers on the ground away from your vehicle while filling.
· Do not fill gasoline containers inside a vehicle or on a truck or trailer bed, because interior carpets or plastic
truck bed liners may insulate the container and slow the loss of any static charge.
· When practical, remove gas-powered equipment from the truck or trailer and refuel the equipment with its
wheels on the ground.
· If this is not possible, then refuel such equipment on a truck or trailer from a portable container, rather than
from a gasoline dispenser nozzle.
· If a gasoline dispenser nozzle must be used, keep the nozzle in contact with rim of the fuel tank or container
opening at all times until fueling is complete.
POTENTIAL HAZARD
· Gasoline vapor can collect inside enclosed trailers and may be ignited by electrical sparks or hot
engine/exhaust components.
WHAT CAN HAPPEN
· Explosion and fire may occur, resulting in property damage, personal injury, and/or death.
HOW TO AVOID THE HAZARD
· Provide adequate ventilation of any enclosed trailer to prevent build up of gasoline vapors, especially at
floor level.
· Refuel only outdoors, never inside an enclosed trailer.
· Be sure all fuel tanks and gasoline storage containers have proper caps installed to prevent spillage and
minimize vapor escaping into the trailer.
· Do not place any equipment that is leaking gasoline into an enclosed trailer.
1.4 OPERATION
Although hazard control and accident prevention partially are dependent upon the design and configuration of the
equipment, these factors are also dependent upon the awareness, concern, prudence, and proper training of the personnel
involved in the operation, transport, maintenance, and the storage of the equipment. It is essential that all Operator Safety
Mechanisms be connected and in operating condition prior to use for mowing.

8
POTENTAL HAZARD
· Operating engine parts, especially the muffler, become extremely hot.
WHAT CAN HAPPEN
· Severe burns can occur on contact.
· Debris, such as leaves, grass, brush, etc. can catch fire.
HOW TO AVOID THE HAZARD
· Allow engine parts, especially the muffler, to cool before touching.
· Remove accumulated debris from muffler and engine area.
· Install and maintain a spark arrester in working order before using equipment on forest-covered, grass-covered,
or brush-covered unimproved land.
POTENTIAL HAZARD
· Hands, feet, hair, clothing, or accessories can become entangled in rotating parts.
WHAT CAN HAPPEN
· Contact with rotating parts can cause traumatic amputation or severe lacerations.
HOW TO AVOID THE HAZARD
· Do not operate the machine without guards, shields, and safety devices in place and working properly.
· Keep hands, feet, hair, jewelry, or clothing away from rotating parts.
1.4.1 Give complete, undivided attention to the job at hand.
1.4.2 Mow only in daylight or good artificial light; keep away from holes and hidden hazards. NEVER carry passengers.
DO NOT operate the mower when children or others are in the area!
1.4.3 When feasible, avoid operating the equipment in wet grass.
1.4.4 Use extreme caution when mowing and/or turning on slopes as loss of traction and/or tip-over could occur. The
operator is responsible for safe operation on slopes.
POTENTIAL HAZARD
· Mowing on wet grass or steep slopes can cause sliding and loss of control.
WHAT CAN HAPPEN
· Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious
injury, death, or drowning.
HOW TO AVOID THE HAZARD
· Do not mow on slopes when grass is wet.
· Do not mow near drop-offs or near water.
· Do not mow on slopes greater than 15 degrees.
· Reduce speed and use extreme caution on slopes.
· Avoid sudden turns or rapid speed changes.

9
Use a hand trimmer only near drop-offs, ditches, steep banks, or water. This area can be dangerous, see Figure 1.
Progressively greater care is needed as the slope increases.
Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly
off the slope.
Avoid sudden starts when mowing uphill. Mower may tip backwards.
Be aware that loss of traction may occur going downhill. Weight transfer to the front wheels may cause drive wheels
to slip and cause loss of braking and steering.
Watch for ditches, holes, rocks, dips, and rises that change the operating angle, as rough terrain could overturn the
machine.
Use extreme care with grass catchers or attachments. These can change the stability of the machine and cause loss of
control.
1.4.5 Stop the blades when transporting the mower to and from the area to be mowed.
1.4.6 Never operate the mower with defective guards, shields, or covers. Always have safety shields, guards, switches,
and other devices in place and in proper working condition.
1.4.7 DO NOT change the engine governor setting or overspend the engine. Operating an engine at excessive speed may
increase the hazard of personal injury.
1.4.8 Disengage PTO before starting engine.
1.4.9 Start the engine carefully with feet well away from the blades.
1.4.10 Keep hands, feet, and clothing away from rotating parts while the mower is being operated.
1.4.11 Stop engine, wait for all mowing parts to stop, and remove key:
Before checking, cleaning, or working on the mower.
After striking a foreign object (inspect mower for damage and make repairs before restarting and operating the
mower).
Before clearing blockages.
Whenever you leave the mower.
Stop the engine and wait for all moving parts to stop:
Before refueling.
Before dumping the grass catcher.
1.4.12 The fuel system is provided with a shut-off valve. CLOSE VALVE:
When the machine will not be used for a few days.
During transport to and from the job.
When parked inside a building.
1.4.13 This mower was designed for one operator only. Keep all others away from mower during operation.
1.4.14 DO NOT mow with the discharge deflector raised, removed, or altered unless there is a grass collection system or
mulch kit in place and working properly.
1.4.15 Be aware of the mower discharge and direct discharge away from others.
1.4.16 DO NOT operate the mower under the influence of alcohol and/or drugs.
1.4.17 Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

10
1.5 MAINTENANCE AND STORAGE
1.5.1 For engine maintenance, follow the engine manufacturer’s recommendations precisely as stated in the engine
manual.
1.5.2 Keep engine and engine-area, free from accumulation of grass, leaves, excessive grease or oil and other debris,
which can accumulate in these areas. These materials can become combustible and may result in a fire.
1.5.3 Store fuel in a container specifically designed for this purpose and in a cool, dry place.
1.5.4 Keep the mower and fuel container in locked storage to prevent children from playing or tampering with them.
1.5.5 Gasoline powered equipment or fuel containers should not be stored in a basement or any enclosed area where open
pilot lights or heat appliances are present.
1.5.6 Maximum mowing results and safety can only be achieved if the mower is properly maintained and operated
correctly.
1.5.7 Check all bolts frequently to maintain proper tightness.
1.5.8 Keep all guards, shields, and safety devices in place and in safe working condition.
1.5.9 Frequently check for worn or deteriorating components that could create a hazard.
1.5.10 All replacement parts must be the same as or equivalent to the parts supplied on the original equipment.
1.6 SAFETY DECALS
1.6.1 Keep all safety decals legible. Remove all grease, dirt, and debris from safety decals and instructional labels.
1.6.2 Safety decals must be replaced if they are missing or illegible.
1.6.3 When new components are installed, be sure that current safety decals are affixed to the replaced components.
1.6.4 New safety decals may be obtained from your authorized equipment dealer or distributor or from Worldlawn
Power Equipment, Inc.
1.6.5 Safety decals may be affixed by peeling off the backing to expose the adhesive surface. Apply only to clean, dry
surface. Smooth to remove any air bubbles.
1.6.6 Familiarize yourself with the following safety decals and instruction labels. They are critical to the safe operation of
your machine.
Decals and their locations are as follows:
1. On the panel of rear frame
2. On the panel of console (Electric)

11
3. On the panel of mower deck
4. On the panel of mower deck
5. On the panel of mower deck and guard plate of LH&RH belt shield
6. In front of the console plate
7. On the panel of rear frame

12
8. On the panel of mower deck
9. On the Mower Deck
9. On the Mower Deck
10. On the panel of console (Recoil BS&Honda)
11. On the left side of front frame
12. On the right side of front frame
13. On the panel of console (Recoil Kawasaki)
14. On the front of the mower deck

13
2. SPECIFICATIONS
2.1 Model Number:
WY28T11BS、WY28T11BSE、WY28T11HD、WY28T11HDE
2.2 Engine:
MODEL
ENGINE
STARTER
WY28T11BS
B＆S10.5HP Intek I\C
Recoil
WY28T11BSE
B＆S11.5HP Intek I\C
Electric
WY28T11HD
HONDA 11HP
Recoil
WY28T11HDE
HONDA 11HP
Electric
2.3 Frame Assembly
Front Frame: Rectangle tube 1.6"×1.18"×0.12"
Thickness (Steel plate of engine frame): 0.12"
Fuel Tank: 2 gallon (7.6 liter) seamless polyethylene
Drive Wheel: 13×4" two-ply pneumatic tubeless.
Caster Wheel: 8×3", smooth, needle bearing pneumatic tubeless.
2.4 Drive System
Type: Belt drive with twin power belts for increased friction to pulley surface.
Transmissions: Peerless 3-speed transmission
Steering/Travel Control: Clutch/brake fingertip steering, key lock switch.
Brakes: band brake, one on each wheel.
Safety Group: Hand actuated operator presence system with blade clutch and transmission interlock to engine kills.
Forward Speed Range: 0-4.38mph(0-7km/h)
2.5 Cutting Deck
Type: Floating deck
True Cutting Width: 28"（71.1cm）
Blade engagement: Manual control
Cutting Height Adjustment: Manual adjustment 1.5″ (3.8cm) to 4.0″ (10.16cm) in 0.5″ (1.27cm) increments.
Cutting Blades: 0.2"(5mm) thick, two 14.5″(36.8cm) blades.
Cutting Deck Belts: A-section.
Synchronous Belt: 1200-8M
2.6 Operator Controls (See FIG 1)
Key switch: Located on the control panel (some recoil starter models are not equipped with key switch). Recoil
starter has two positions. Turning to "on" starts the engine; turning to "off" stops the engine. Electronic ignition
model has three positions. When starting, turn to "start" position; then remove your hand.
Throttle Control: Located on the control panel. Throttle is used to control engine speed. Moving throttle lever
forward will increase engine speed and moving throttle lever to the rear will decrease engine speed. Some recoil
starter models are not equipped with key switch. Move the throttle lever to the rearmost position, then the engine will
be switched off.
Blade Drive Lever: Push the mower blade drive lever forward to the engage position. Pull the mower blade drive
lever backward to the disengage position to stop the blades.
Hand actuated operator presence lever: When in normal operation, compress the operator presence lever. When
released, engine will kill.
Steering Brake Levers: While squeezing the steering lever handles with both hands, release right and left neutral
latches; then release right and left steering levers to move forward. When the steering levers are released, the mower

14
will travel straight forward. To make a right turn, squeeze the RH steering lever. To turn left, squeeze the LH steering
lever. Squeeze both steering levers, lock right and left neutral latches, and the mower will stop.
Neutral Latches: Located on bottom of the handles. They are used to lock the steering brake levers when stopping.
Gear shift lever: It is used to control the speed. When the machine is moving forward, if you’d like to change low
gear into high gear, push gear shift lever forward, then you can change the gear. When changing high gear into low
gear, you must stop the machine, then change the gear.
Fuel shut-off valve: The fuel shut-off valve is used to shut off the fuel when the machine will not be used for a few
days, during transport to and from the jobsite, and when parked inside a building.
FIG 1
2.7Accessories:
a) Grass catcher assembly (WY32-NGC): 80L, see FIG 2
b) Mulching Assembly (2832010): See FIG 3
FIG 2
FIG 3
2.8Approximate Dimensions:
2.8.1 Width:
Without Deck
Discharge
chute up
Discharge
chute down
27.8in
（70.5cm）
28.8in
（73.2cm）
37.8 in
（96 cm）

15
2.8.2 Overall Length: 67.3in（171.0cm）
2.8.3 Overall Height: 42.9in (109.0cm)
2.8.4 Tread:
Drive Wheel Tread: 23in（58.6cm）
Caster Wheel Tread: 20.6in（52.3cm）
2.8.5 Wheelbase:
31.9in（81cm）
2.8.6 Curb Weight: 338lbs（154Kg）
2.9 Torque Requirements
Cutter Housing Spindle Nut: 66± 13ft-lb (90±18N-m)
Engine Deck/Front Frame Mounting Bolts: 40-52ft-lb (55-70 N-m)
3. ASSEMBLY INSTRUCTIONS
3.1 Open Crate
Open crate. Remove the loose parts (i.e., operator’s manual, etc) from crate. Remove unit from crate; check there are no
loose parts left.
3.2 Initial Instructions
Attach the handle with four M10×25 Flange Hd. Bolts and four M10 locknuts on each side as shown in FIG 4.
Insert rod end connector threaded stud of left and right steering linkage rod assemblies through hole of left and right
brake swing arms; add M6 nut and washer 8 and tighten. Next, insert rod end connector threaded stud of shift control
rod assembly through hole of shift control arm; add M6 nut and washer 6 and tighten. To finish, insert rod end
connector threaded stud of blade control rod assembly through hole of tension swing arm; add M6 nut and washer 6
and tighten. See FIG 4
The Throttle Cable must be attached to the engine according to the Engine Operator's Manual. The Fuel Tank Line
connects to the line of the engine. (The positions of Fuel Filter and Throttle Cable Attachment are a bit different on
different models of Engines.) See FIG 5

16
FIG 4
FIG 5
3.3 Service Engine
Engine is shipped without oil. Fill to the appropriate level with SAE10W-30 or 10W-40.
4. OPERATION INSTRUCTIONS
Read these instructions carefully before operating the mower.
4.1 PRE-START
Fill fuel tanks. For best results use only clean, fresh, regular grade, unleaded gasoline with an octane rating of 87 or
higher. Regular grade leaded gasoline may also be used; however, combustion chamber and cylinder head will
require more frequent service. See Engine Owner’s Manual. Do not add oil to gasoline. Do not overfill fuel tank.
Open the fuel tank shut-off valve.
Make sure you understand the controls, their locations, their functions, their safety requirements, and how to stop
quickly.
POTENTIAL HAZARD
·The rotating blades under the mower deck are dangerous.
WHAT CAN HAPPEN
·Blade contact can cause serious injury or kill you.
HOW TO AVOID THE HAZARD
·DO NOT put hands or feet under the mower or mower deck when the blades are engaged.
Refer to Maintenance, Section 5, and perform all necessary inspection and maintenance steps.
Check tire pressure in drive wheels. Proper inflation pressure for tires is 30psi (210kpa).
Check tire pressure in caster wheels. Proper inflation pressure for tires is 30psi (210kpa).

17
4.2 Starting Engine
Turn the key switch to the “ON” position. The transmission must be in neutral, the blade drive lever must be
disengaged. 1）For recoil with key, turn the key switch to the “ON” position, pull the cable to start the engine. 2）For
recoil without key, intermittently pull the cable to start the engine. 3）For electric start, turn the key switch to the
“Start” position to start the engine.
On a cold engine, place the throttle midway between the “SLOW″ and “FAST″ positions and push choke lever
forward to the “ON″ position. Turn ignition switch to the “start″ position. Release the switch as soon as the engine
starts.
4.3 MOWER OPERATION
Push blade drive lever forward to engage blades. Pull blade drive lever back to disengage blades. Be sure that all
persons are clear of mower deck and discharge area before engaging PTO.
IMPORTANT: Set the throttle to “midway″ position. Push blade drive lever to the “ROTATE″ position. Speed up the
throttle, begin to mow.
Stopping the blades: Set the throttle to the “midway″ position, pull the mower blade drive lever backward to the
“disengage” position to stop the blades.
POTENTIAL HAZARD
·An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also,
contact with the blade could occur.
WHAT CAN HAPPEN
·Thrown objects or blade contact can cause serious injury or death.
HOW TO AVOID THE HAZARD
·Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection
system or mulch kit in place and working properly.
4.4 Moving Operation
Squeeze the right and left steering lever handle bars and move neutral latches into the lock position. Release handle bars
and select speed by moving the gear shift lever from the neutral position to the desired speed.
Squeeze the right and left steering levers, release the locks, and then release the steering levers to move forward slowly.
Squeeze the right steering lever to turn right and the left steering lever to turn left.
4.5 Stopping engine:
Pull the blade drive lever backward to the disengage position to stop the blades. Squeeze the right and left steering lever
handle bars and move neutral latches into the lock position. Rotate key switch to the “OFF″position. Remove the key to
prevent children or other unauthorized persons from starting the engine. Close fuel shut-off valve when the machine will
not be used for a few days, transporting, and when the unit is parked inside a building.

18
5.MAINTENANCE&ADJUSTMENTS
POTENTIAL HAZARD
·While maintenance or adjustments are being made, someone could start the engine.
WHAT CAN HAPPEN
·Accidental starting of the engine could seriously injure you or other bystanders.
HOW TO AVOID THE HAZARD
·Remove the key from the ignition switch and pull the wire off the spark plug before you do any
maintenance. Also push the wire aside so it does not accidentally contact the spark plug.
POTENTIAL HAZARD
·The engine can become very hot.
WHAT CAN HAPPEN
·Touching a hot engine can cause severe burns.
HOW TOAVOID THE HAZARD
·Allow the engine to cool completely before servicing or making repairs around the engine area.
5.1 PERIODIC MAINTENANCE
5.1.1 Check the engine oil level.
Service Interval: Daily
Make sure unit is on a level surface. Stop engine, wait for all moving parts to stop, remove key or pull out spark plug
lead.
Check when engine is cold.
Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick. Do not screw into place.
Remove the dipstick and read the oil level.
If the oil level is low, add oil to bring the oil level up to the "FULL" mark on the dipstick. Use oil as specified in the
Engine Owner’s Manual.
IMPORTANT: DO NOT operate the engine with the oil level below the "LOW" or "ADD" mark on the dipstick or over
the "FULL" mark.
5.1.2 Clean EngineAir Cooling System.
Service Interval: Daily or more often in dry conditions
Stop engine, wait for all moving parts to stop, and remove the key.
Clean all debris from rotating engine air intake screen and from around engine shrouding.

19

POTENTIAL HAZARD
·Excessive debris can cause the engine and hydraulic system to overheat.
WHAT CAN HAPPEN
·Excessive debris around the engine cooling air intake and inside of the pump compartment can create a fire
hazard.
HOW TO AVOID THE HAZARD
·Clean all debris from around the engine and hydraulic pumps daily.
a) Stop engine, wait for all moving parts to stop, and remove the key.
b) Clean all debris from rotating engine air intake screen and from around engine shrouding.
5.1.3 Clean grass build-up from under deck.
Service Interval: Daily
Stop engine, wait for all moving parts to stop, and remove key.
Clean out any grass build-up from the underside of deck and in discharge chute.
5.1.4 Check mower blades.
Service Interval: Daily
Stop engine, wait for all moving parts to stop, and remove key or pull out spark plug lead.
Lift deck.
Inspect blades and sharpen or replace as required.
Re-install the blades (if they were removed) by placing a block of wood between the front or rear baffles and the
blade; then torque the blade bolts to 66±13ft-lb (90±18N-M). Be sure the spring disk washer cone is installed toward
the bolt head.（See FIG 6）
FIG 6

20
POTENTIAL HAZARD
·Operating a mower deck with loose or weakened blade bolts can be dangerous.
WHAT CAN HAPPEN
·A loose or weakened blade bolt could allow a blade rotating at a high speed to come out from under the deck,
causing serious injury or property damage.
HOW TOAVOID THE HAZARD
·DO NOT lubricate the threads of the bolt or spindle before assembly.
·Torque the blade bolt to 66±13ft-lb (90±18N-M).
·Stop engine, wait for all moving parts to stop, and remove key or pull out spark plug
lead before removing blades.
5.1.5 Check safety interlock system.
Service Interval: Daily
Check starting circuit:
- Ignition switch must be in the “ON”or “START”position.
- Transmission must be in neutral.
- Blade drive lever must be disengaged to start engine with recoil starter.
Check engine "kill" (flameout) circuit:
Remove your hands from the Operator Presence Control Lever when the engine is running and the engine should stop
running within 3 seconds.
NOTE: If machine does not pass any of these tests, do not operate. Contact your authorized WORLDLAWN POWER
EQUIPMENT SERVICE DEALER. It is essential that operator safety mechanisms be connected and in proper operating
condition prior to use for mowing.
5.1.6 Check for loose hardware.
Service Interval: Daily
Stop engine, wait for all moving parts to stop, and remove key.
Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the
problem before operating.
5.1.7 Service air cleaner.
Service Interval: 50 hrs
Check more often under severe conditions. See engine manual for additional information.
Stop engine, wait for all moving parts to stop, and remove the key.
Loosen retaining clips and remove air cleaner compartment cover.
Remove paper element. Check the condition of the paper element. Replace if dirty, bent or damaged.
Do NOT wash or use pressurized air to clean paper element or inner element.
5.1.8 Change engine oil.
Service Interval: 100 hrs
NOTE: Change oil and filter after first five (5) hrs. of operation.
Stop engine, wait for all moving parts to stop, and remove key.