wysLink WHS400 Instruction manual

WHS400
Cloud Camera
Quick Start Manual
Package Contents
In a the package, there are
two poly form containers,
you will find:
WHS400 camera (qty. 1)
power adapter (qty. 1)
antenna (qty. 1)
wall screws (qty. 4)
Camera Connection
1. Install the antenna on the camera.
2. Plug one side of a network cable into the LAN port on rear
panel and the other side into your router.
3. Connect the provided 5VDC power adapter to the
camera.
1/8
Camera Mounting
WHS400 is designed to be used in outdoor. Check the view
area and find a best location; it still suggested to be mounted
where the rain cannot reach though the camera is water
proof. Use attached 4 screws or the screws matched the wall
materials.
2/8
Camera Registration on wysLink.com
Please register your IP camera on wyslink.com following the
next steps.
1. Create an account on www.wysLink.com and activate
it. If you already have a wysLink account, please ignore
this step. Then log in and enter Live Channel Editor.
2. In Channel Editor, click the Edit Device button.
Add Your Device:
Input the last 4 digit of S/N
and Password to find your
camera.
S/N: HS201311E023
Password is printed on the
label.
3. Now, your camera is listed in My Device List.
Assign Your Device to a Channel:
Click an available channel that is not assigned to other devices.
Click your camera row to select it.
Then click [Assign to Channel] button to put this camera
into your selected channel.
3/8
Watch Live Video
After registration, please connect your camera with network, then power
on.
1. After power on your camera, please wait about 30 seconds.
2. Click [Refresh] button below My Channel List.
3. When the channel status displays “streaming”, your camera streams
live video to your channel. If it shows “online”, click [Start stream]
please.
Click your account dropdown list at the top-right corner of the webpage
and then click [My Stage]. Now you enter your stage.
4. Click your channel icon. You can watch your video on stage.
4/8

Control on My Stage
All control buttons are located on the top of the displayer on
My Stage.
Alarm Indicator
Snapshot
Watch Recorded
Video
Full Screen
Display
Camera Settings
Volume Control
12 3 4 5 6
Watch Recorded Video on Cloud
This function is for premium member only.
1. Drag the white marker on the date bar (the lower bar) to
select the video date.
2. Click the time bar (the upper bar) to select the exact time.
Save Recorded Video at Local
1. Ctrl + click the time bar to select the start time.
2. Alt + click the time bar to select the end time.
3. Click Clip button and wait for finishing download.
4. Click Save button and select the save path.
5. Click Live button on the top of the player to return live
video.
5/8
Camera Settings on Channel Editor
1. Enter Channel Editor Webpage.
2. Click the channel assigned to your camera.
3. Click Device Config button below My Channel List. You can set video,
Wi-Fi, alarm, PTZ, Time.
Video Settings:
Brightness
Contrast
Frame rate (FPS)
Image size
Image direction
If you would like to
save your network
traffic, please set
small size and low FPS.
Wi-Fi Setting: Before setting up
WiFi, Please make sure power cable
and LAN cable are connected to the camera.
Click [WiFi] button.
Click [WiFi Scan] button.
Click WiFi name to
select your WiFi.
Input WiFi password.
Click [Set to Camera].
Click [OK] button.
Please turn off the power
and remove LAN cable.
Wait for about 4 minutes,
Turn on the power to
restart your camera. 6/8
Camera Specification
Video
compression format
H.264
Resolution
HD(1280×960), VGA(640×480)
Image sensor
CMOS 1.3M Pixels
Lens
3.6 mm
Frame rate
up to 25 fps
Image adjustment
brightness, contrast
WB, BLC
auto
Audio
G.711 / G.726
only for live video
Network
Interface
RJ-45 /100Mb
Wireless
Wi-Fi 802.11 b/g/n
Protocols TCP/IP, HTTP, DHCP, SMTP, RTMP,
wysLink Plug&Play
Alarm
Motion detection
support
Alarm notification
by mail or shot message via
wysLink.com (Premium member only)
Pan/Tilt
Horizontal/ Vertical
355°/ 90°
Preset position
7 positions
Night Vision
LED
22×Φ5 LED lights
IR distance
20 meter
Smart Phone Apps
Android iPhone iPad
Please scan above QR codes to download the application. Or
please search wysLink on Google show for Android, itunes
iphone or iPad.
7/8
Motion Alarm needs to be turned on again if the video resolution has
been changed. The interval between alarms is 5 minutes.
More Information
For more information about your
camera or related software
applications, please visit our
website www.wyslink.com.
Notes:
It is a cloud camera to be accessed via our cloud service platform, wysLink.com. The
camera can also be locally or globally accessed by inputting its local IP address on a
browser, which is available to users who have some knowledge about IT and network. If
changed camera parameters during local access cause camera abnormal on
wysLink.com, users assume responsibility.
Designs and specifications are subject to change without notice, please
visit www.wyslink.com for updated information.
2014/03/01 version 1.1
8/8





