XD Design Flowerpot speaker User manual

1
Flowerpot
speaker
Copyright© XD P326.973

3
ENGLISH
Congratulations on your Bluetooth Flower pot speaker!
This Bluetooth speaker allows you to enjoy your music
without wires and by touching your plant, you can make a
wonderful piano sound. Please read this manual before use.
DEVICE LAY-OUT:
1. 2.
3. 4. 5.
6.
7.
1. Power mode / Bluetooth mode
2. Next / Light
3. USB charging
4. Water outlet
5. Speaker
6. Touch sensors
7. Water scupper

4
CHARGING THE SPEAKER:
A full charge is approximately 4 hours and plays continuously
for 12 hours.
- Connect the speaker to the USB charging cable to charge.
INSTRUCTIONS:
1. Smart fun:
You can make this flowerpot make a wonderful piano sound.
The flowerpot plays dierent fun tunes.
2. Bluetooth speaker:
Switch Bluetooth mode on and instantly your flowerpot
becomes a fashionable Bluetooth speaker.
3. Light mode:
The flowerpot has a rainbow light mode, with seven dierent
colours.
SMART FUN FUNCTION:
A) Plant your favourite plant in the flowerpot; water them
lightly to keep the soil moist.
NOTE: The sensitivity of contact is dierent because of dierent
plants.
B) Press power mode long (1) to start the smart fun function. By
touching the plant, you can make a nice piano sound. Press next
(2) to switch tune. When you found your favourite tune, you
have to touch the plant once and the tune will stop automatical-
ly. You can finish the tune by touching the plant.

5
BLUETOOTH SPEAKER FUNCTION:
Press power mode shortly (1) and the flowerpot will change into
a Bluetooth speaker.
Pairing: To connect your speaker turn on your Bluetooth mode
and connect with pairing name “flowerpot speaker” on your
mobile device. When the speaker is connected successfully, the
blue light goes out automatically.
LIGHT MODE FUNCTION:
THE KEYS MODE:
Short press (2) to turn on the mood light.
Press again for changing rainbow colours. Press again button
(2) or turn o the light.
TOUCH MODE:
Press long (2) to activate the touch function mode. By touching
the pot or plant the light will change.
Press long again (2) again to go back to the keys mode.
TROUBLESHOOTING:
- Unable to boot: Check the battery for electricity, please
charge, when charging the red indicator lights up and is filled
with red lights.
- The harps are not very sensitive: If the pot is too dry, please
give the plant water properly or the sensitivity of the touch is
aected by the current magnetic field under charge.

6
SPECIFICATIONS:
Pairing name Flowerpot speaker
Output power 5W3
Wireless frequency 20-20 KHz
Bluetooth distance 10m
Battery capacity 1200 mAh
Working voltage 3.7 V
Playing time 12 hours
Charging time 4 hours
Bluetooth version 4.2
SUCCULENT PLANT
-Witchford
-Aloe Vera
-Benth ex E.Mey etc
PEPPER GRASSES
- Peperomia tetraphylla
- Peperomia caperata
- Peperomia clusiaefolia
SANSEVIERIA
- Pacers Sansevieria
- Bergamot Sansevieria
- Banana Sansevieria
OTHERS
- Murraya exotica
- Sempervivum tectorum
- Epipremnum aureum
ADVICE PLANT:


FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a class B
digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequence energy and,if
not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that interference
will not accor in a particular installation.if this equipmemt does cause harmful
interference to radio or television reception,which can be determined by turning the
equipment off and on,the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which the
receiver is connectec.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement
The device has been evaluated to meet general RF exposure requirement.The
device can be used in protable exposure condition without restriction.
