Xerox Wireless Print Solutions Adapter Guide

www.xerox.com/office/WPSAsupport
110V/220V 50/60 Hz
1.1
4.1
4.2
4.3
1.2
1
3 4
2
Select and install one of the AC plug adapters on
the 5 VDC Power Supply. Ensure that the adapter
snaps securely and fully into the base.
Plug the Ethernet cable into your printer and the
Wireless Print Solutions Adapter.
Plug in the power adapter to a wall outlet
(110 V/220 V AC) or a power strip. Wait until the
Status LED flashes amber.
Apply the included rubber feet or hook-and-loop
strips to the base of the unit. If you are attaching
the device to the printer, ensure that you do not
block vents or access doors.
Installating the Hardware
Xerox®Wireless Print Solutions Adapter
Installation and Connection Setup Guide
installation_and_connection_setup_guide.pdf 1 8/11/15 7:53 AM

www.xerox.com/office/WPSAsupport
192.168.0.1
192.168.0.1
admin
PASS
wpsa-xxxx
2
1
2.1
2.1
2.3
To access the web interface of the Wireless Print
Solutions Adapter, open a browser. In the URL
field, enter the default IP address of 192.168.0.1,
then press Enter or Go. Log in to the Web
interface.
Note: The default User Name is admin and the
default Password is PASS. Both values are case-
sensitive.
PC/Laptop Display: There are five main tabs
across the top of the screen.
Mobile Device Display: The main tabs are
arranged vertically. To expose the tabs, touch the
icon at the top of the screen.
There are 2 Web Interface formats:
Setting up the Connection Using the Web Interface
On your computer or mobile device, navigate to
your list of available wireless networks. Select
the available network that appears as wpsa-
xxxx where xxxx is the last four characters of the
MAC address of your adapter (not the Wireless
MAC address). You can find the MAC address on
the label that is located on the bottom of your
adapter.
installation_and_connection_setup_guide.pdf 2 8/11/15 7:53 AM

www.xerox.com/office/WPSAsupport
English
Français
Italiano
Deutsch
Español
Português
Русский
3
4
5
7
8
6
3
At the top of the Quick Setup screen, if needed,
click the menu, then select a language. In a few
seconds, the screen refreshes and displays the
selected language. You may need to log in again.
Note: if the Quick Setup page does not appear,
click the Administration tab, then in the
navigation pane, select Quick Setup.
4
For Bridge 1 (br0) Configuration, select Enabled.
Leave the Bridging MAC Address field blank.
5
Optionally, if your wireless router supports WPS
and it is enabled, you can use WPS. If WPS is
preferred, click the protocol that your router
supports. Options are WPS (PBC) or WPS (PIN). For
details, refer to the documentation for your router.
Proceed to Step 8.
6
From the list of Available Networks, click the
required network’s SSID.
7
For Connect To, enter the credentials for the SSID
that you selected.
8
Leave the fields for Printer and Add Printer blank.
Click Submit, then to confirm, click OK.
installation_and_connection_setup_guide.pdf 3 8/11/15 7:53 AM

www.xerox.com/office/WPSAsupport
xx.xxx.xx.xxx
9 10
12
34
Record the IP address for later reference.
To locate the new IP address, click the Status tab,
then scroll down to the Network section. Under
Interface wlan0, note the IP address.
Record the first four sections but ignore /xx.... If no
IP address appears, wait, then refresh the browser
and check again.
Click the Administration tab, then click the
Reboot button.
Adding the Printer
If the Web UI is open, close all Web browser
windows and wait for the Status LED on the
Wireless Print Solutions Adapter to turn green.
Restart the printer connected to the Wireless Print
Solutions Adapter. For details, refer to your printer
documentation.
Locate the IP address of your printer. To find the
IP address, at the printer control panel, open the
Machine Status screen, or print a Configuration
Page. For details, refer to the documentation for
your printer. For Xerox®printer documentation, go
to www.xerox.com/support.
Open the Wireless Print Solutions Adapter Web
Interface. For details, see steps 1 and 2 in Setting
up the Connection Using the Web Interface.
installation_and_connection_setup_guide.pdf 4 8/11/15 7:53 AM

5 6
Click the Printer tab. For Add Printer, enter the IP
Address and name of your printer, then click Add
Printer.
When the web page refreshes, to verify correct
installation and operation, click Print Test Page.
You can configure additional setup and features
as needed.
For troubleshooting and additional help
information, refer to www.xerox.com/office/
WPSAsupport. In the Search for Keyword or
Phrase field, enter troubleshooting.
© 2015 Xerox Corporation. All Rights Reserved. Xerox®, and Xerox and Design®are trademarks of Xerox Corporation
in the United States and/or other countries. BR#15961
installation_and_connection_setup_guide.pdf 5 8/11/15 7:53 AM