XINDAK C06 User manual

CD Player
C06
INSTRUCTIONS
®

Caution!!!
To reduce the risk of electrical shock, DO NOT remove cover. No user-serviceable parts inside. Refer
servicing to qualified personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to presence of uninsulated “Dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
Dangerous Voltage
The exclamation point within an equilateral triangle is intended to alert the
user to presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Important Instructions
Marking by the CE symbol shown left
indicates compliance of this device with the
EMS Electrornagnetic Compatibility and
LVD low voltage directive) standards of the
European Community.
" " ( )
( )
(
Please read all instructions and precautions carefully and
completely before operating your C06 CD-Player. Then,
please keep this manual for referring in future.
Recommend this unit only for family using.
CD player
Unit.
Chapter 1 Important Safety Instruction

Unpack your C06 CD Player and keep all packing materials for future transport or service, locate and remove all
accessory items from the accessory box within the controller shipping carton.
Accessories Included:
Please read all instructions and precautions carefully and completely before operating your C06 CD Player.
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Always keep this unit out of the reach of children.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus ( including amplifiers) that
produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
10. Unplug this apparatus during lightning storms or when unused for a long time.
11. Always disconnect your entire system from the AC mains before connecting or disconnecting any cable, or when cleaning any
component.
12. This product must be terminated with a three conductor AC mains power cord which includes an earth ground connection, to
prevent shock hazard, all three connections must always be used.
13. AC extension cords are not recommended for use with this product.
14. Never use flammable or combustible chemicals for cleaning audio components.
15. Never operate this product with any cover removed.
16. Never pour or spill liquids directly onto this unit.
17. Never block air flow through ventilation slots or heat sinks.
18.Never by pass any fuse.
19. Never replace any fuse with a value or type other than those specified.
20. Never attempt to repair this product, if a problem occurs, contact your dealer.
21. Never expose this product to extremely high or low temperatures.
22. Never operate this product in an explosive atmosphere.
1. AC power cord × 1 2. Remote controller × 1 3. User manual (This manual)
1.2 Check Accessory
Chapter 1
1.1 Before Use
Important Safety Instruction
2

2.1 Precaution In Use
2.2 Condensation
Precaution
，
.
Fig.1
receiver
Chapter 2
3
on

2.3 Compact Discs
This player can play back the CD-RW (Re-Writable) discs as well as ordinary Audio CD and CD-R (Recordable) discs.
Please do not play the CD which is not round, otherwise it may cause fault on this player.
Precaution
Supported Disc
CD CD-R CD-RW
iDO NOT USE the special shape disc or metamorphic disc
Chapter 2
4

AAA Batteries
Install Batteries
Before using the remote controller for the first time, you need install
the new battery in the remote controller.
1. Use the tool to remove the rear cover of the remote control unit.
3. Reinstall the rear cover of the remote control unit.
1. Do not use new and old batteries simultaneously.
2. Batteries with similar shapes may have different rated voltages
Be sure to use the correct batteries.
3. Remove batteries from the remote control unit if it will not be used
for a long period of time.
Process
Battery Replacement
2. Install the 2 batteries (AAA) polarity.
1. Use the tool remove the rear cover of the remote control unit.
2. Take out the old batteries from remote control unit.
. Install the 2 batteries (AAA) polarity.
4. Reinstall the rear cover of the remote control unit.
Caution
If you use the remote control unit to control the amplifier:
1.The remote control range is approximately 5 meters.
2.Pointing the remote control on an angle to the receiver, will
shorten the useful distance of the remote control.
with correct +/-
3 with correct +/-
Using Remote Controller
Incorrect use of batteries
n shorter battery life.
may cause corrosion or damage.
The lower temperature, the
2.4 For Using the Remote Controller
Install Batteries
Precaution
Battery Reclaim
Please send the waste batteries to local battery
reclaim center. DO NOT discard the waste
batteries discretionarily, in order to avoid
environment pollution.
5
Chapter 2

2.5 Remote Controller
Precaution
Chapter 2
6
7. Search Forward
When button is pressed during play, the CD player will begin to scan
forward with the speed 4 times of the normal speed. When the button is kept
to pressed for 4 seconds or longer, the CD player will begin to scan forward
with 8 times speed of normal. Then release the pressure, the unit will resume
normal play.
8
8. Search Backward
When button is pressed during play, the CD player will begin to scan
backward with the speed 4 times of the normal speed. When the button is
kept to pressed for 4 seconds or longer, the CD player will begin to scan
backward with 8 times speed of normal. Then release the pressure, the unit
will resume normal play.
7
9.Stop Play
Press button to stop play.
10. Pause Play
Press button to stop play temporarily.
;
11.Play
Press button to start play.
4
12. Skip Forward
Press button, the CD player will skip to the beginning of the next
track.
:
9
13. Previous Track
Press button, the CD player will skip to the beginning of the previous
track.
14. Repeat A to B (Chapter 4.4)
15 16. Volume Control : No use for this unit
、
17. Preview Play
Press this button to begin the track intro scan (10 seconds). The player
will play the first 10 seconds of every track. Press the button ‘Clear’ to
cancel this operation.
18. Switch the channel: No use for this unit
19. DIMMER
Press this button to adjust the lighteness of alphanumeric display window as
the order: High-lightness, mid-lightness,low-lightness,close.
5
0
19. Open/Close
Press button to open or close to slide the disc tray out or in.
2. Number Select
Press the number button 1 to 9 to choose the corresponding
song to play. Press two number buttons within 2 seconds to
choose the track number more than 9. For example, press 1
and 2 within 2 seconds, it will skip to No.12 song and play it. If
the number chose exceeds the number range of disc, this
chose will be recognized useless and the player will remain
the current work model.
3.Clear/Cancel
Cancel the function operation.
4.Program Play (Chapter 3.3)
5. Random Play (Chapter 3.6).
6. Repeat play (Chapter 3.4)
1.SACD/CD switch:
No use for this unit

Precaution
2.6 Front Panel
7
.
11. NEXT
6. STOP
10. PLAY
8. PAUSE
Chapter 2
1. IR Sensor
.
2. P Swi chower t
3 ower I. P ndicator
.
4. Alphanumeric Display
5. DISC Tray
9. PRE
.
7. OPEN/CLOSE
This indicator will be light when this unit is switched on.
1 2 4 5
39 108 116 7
2.7 Rear Panel
1.
3.
Audio Output Terminal
2.Digital Coaxial Output Terminal
Fuse Socket
Output the analog stereo audio signal amplified by tube to the input port on the amplifier.
By connecting this jack with digital coaxial cable to output the digital signal to the DAC or receiver.
Connect the power cord to the AC inlet.
Use to install the fuse.
4.AC input socket

Chapter 3
3.1 The Connection
8
The CD player has two audio output models: digital signal output and analog signal output.
Analog Signal Output Digital Signal Output
You can choose the better connection model considering your
audio system.
1. Coaxial Audio Output
Please use coaxial signal cable to connect the coaxial output port
of this unit and make sure the reliability and correctness of the
connection.
The Connection of Analog Output The Connection of Digital Output
Operation Instruction
DAC

Chapter 3
3.2 Start Play
3.3 Program Play
3.4 Repeat Play
Before enjoying the music, please confirm that the connection has been ready as the previous chapter indicated. After that, you can begin to
enjoy the music.
1. Turn on the CD player. After about 30 seconds for warm-up, then press the button to slide the disc tray out, and load a disc on the disc
tray. Press the button again to slide the disc tray in. And the display will show the number and total playing time. The player is ready to play.
2. Press the button to start playing with the first track. Press this button during playing, the player will skip to the beginning of the current
track and play it.
3. Press the button to stop play temporarily. Press it again or press the button, the player will continue to play.
4. Press the button to stop play.
To play the disc as the order you edited
1. Press the button ‘ PROGRAM’ on the remote control during stop to enter the program play model. The display will glisteningly show “
PROG”.
2. Press the button skip forward/backward or directly press the number buttons to enter the track number you want. Then press the button
‘PROGRAM’ to store. The display will show “ 02 00”.
3. Repeat the operation 2 to continue editing the track order.
4. After the edit finished, press the button to play as the order you edited.
5. Press the button ‘ CLEAR’ to cancel the program play.
To repeat the track you chose
1. Repeat all/one selections
Press the button ‘REPEAT’ during playing, the player will switch round among following three models:
Repeat one selection (display ) Repeat all selection (display ALL Cancel the repeat“ ” “ ”
2. Repeat A to B
Press this button during play to mark the Apoint, then the display A . Press this button again to mark the end-point (repeat within 3 seconds
is invalid), then the display shows AB . The player will skip to the A point and repeat playing A to B. Press this button again, repeat will be
canceled.
3. Starting repeat, the sign for repeat will light.
4. Press the button ‘ Clear “ to cancel the repeat.
“ ”
“ ”
“ ”
9
Operation Instruction

Chapter 3
3.5 Preview Play
3.6 Random Play
3.7 Information Window
To start the track intro scan (10 seconds). The player will play the first 10 seconds of every track.
1. Press the ‘INTRO’ button during stop, then the information window will show ‘XX int XX’. The player begins to preview the first track.
2. Press the ‘INTRO’ button during play, then the information window will show ‘XX int XX’. The player begins to preview the next track.
3. Press the skip forward/backward button or directly enter the number of track you want, and the player will intro scan.
4. Press the button ‘Clear’ to cancel this operation.
9:
To random play all of the tracks in disc.
1. Press the ‘RANDOM’ button, and the display will show “rA XX 00” . Then the player will begin to random play the tracks.
2. Press the skip forward/backward button can skip to the next track.
3. Directly press the number buttons to choose the corresponding track, but the random will not bu cancel at the same time.
4. Press the ‘CLEAR’ button to cancel the random play.
9:
Adjust the Lightness of Alphanumeric Display
1. Press the button ‘DIMMER’ during stop or play to adjust the lightness of alphanumeric display window. The lightness will change as
the following order:
High-lightness mid-lightness low-lightness close.
2. When restart the player, the lightness will be same as the last model.
3. The lightness model is set as high-lightness when the unit leaves factory.
When there is no disc laid, press “play+Next” at the same time, and it will display the total word hours for this unit.
10
3.8 Work hour display
Operation Instruction

Specifications
Chapter 4
4.1 Specification
11
General Specifications
Disc:
Sample Rate:
Digital Output:
Power Consumption:
Temperature Range for Using:
Power Supply:
One Disc, 80mm or 120mm
44.1KHz
Coaxial * 1
10W Max.
+5 C~+35 C
Specified on rear panel
° °
Physical Specifications
430mm*110mm*316mm
5Kg
Dimensions(W*H*D):
Net Weight:
Specifications
Analog :Output
S.N.R.:
T.H.D:
Dynamic Range:
Frequency Response:
Digital Coaxial Output:
2V RMS
95dB
0.06%
96dB
20Hz~20KHz
0.5Vp-p
≥
≤

Phone/Fax:[phone]
,
© 2006
XD3.834.066sms