the video and enter standby mode , press again to restart recording.
!2, infrared lights on / off: When the machine runs into normal video recording, long press the C key,
the red light flashes 3 times, then the unit has been into the infrared camera mode. Then long press the C key for, Infrared light goes off
and the camera runs into normal state.
!3,photo taking operation: When the unit runs into the video recording mode, press the A button twice,
the blue light being constantly bright, it runs into standby mode, then press the C key, the indicator light is red, press the A button once
then the red light flashes one time, it means that a photo has been saved successfully. Long press the C key, the blue light will flash for
one time then turns into red light again, it starts the infrared photo taking function.
!4, Motion Detection: When the blue light being constantly bright , the unit runs into standby mode,
then press the C key, the indicator light is red and blue both bright, press the A button once, red and blue lights flashing three times
then goes off, that means it has entered the mobile detection status. Under motion
detection mode, it will automatically runs into video recording mode and red light will flash for one time when it senses a object is
moving. Long press the C key ,the red light flashes three times , it runs into the infrared night vision motion detection status. Then long
press the C key, the indicator will not show anything but the Infrared light goes off ,the camera runs into the normal state
!Note: The camera built-in high-capacity polymer lithium battery, no memory effect, can be used with the charge when you want,
but the initial use of the first five, and then charge the battery to run out of capacity, to start the battery maximum capacity, access to
standard working time.
!5,U disk and net webcam: in the organs of local state of the computer through the USB cable and good connections in my
computer a "removable disk" drive, U disk to use the machine as. In the machine turned on the computer through the USB cable and a
good connection, my computer will appear Standard Camera, the machine used as a webcam.
!Another: differences according to computer configuration or system, the computer can not detect a camera function, if the
occasional computer can not enter into the camera function and a removable disk, remove the camera and the camera connected to a
computer re-boot ; If you are the first to use the camera on your computer, computer camera, install the CD-ROM or dealers inside the
camera driver; To avoid equipment damage, when you are ready to connect the device to your computer, please first the supplied data
cable to the camera, then connect the other end of cable to your computer.
!6, set recording time: the camera provides recording time in video which is displayed in format: year - month - day hour:
minutes: seconds, set the time as follows:
!Connected the watch to computer by USB cable well. ,in my computer have a "removable disk" drive. open the notebook of
windows (*. txt format) Input: 2012.01.24 13:30:30 Y
!Take the file name: time.txt
!Save the file in the root directory of the removable hard drive, then the USB cable connection cut off, then reboot watch and
start recording, video and photographs of the time in bottom right corner is the new time and date
!You can also use the WriteTime.exe reset time, the method is follow. First make the watch connected to the computer, found
the write time .exe then double-click WriteTime.exe, jump to a update window confirm update to as same the compute system time.
!7, a removable disk: in the off state or standby state, you can connect the computer at this time, the computer will eject the
removable disk logo, image file directory is: * plate \ _DCIM \ 100DSCIM;; need to uninstall the camera, please click lower right corner
of the taskbar icon mobile device management, in which the removable storage device unloaded until the system recognizes the
hardware can be safely pulled out, then disconnect the camera and the computer.
!Note: According to the differences in computer configuration or system, identifying the removable disk will be slightly different,
please be patient, this period is best not to carry out the operation of the camera, so the impact on computer recognition hardware. If
the time is not recognized to a removable disk, try to re-insert, if still does not recognize the hardware, make sure your operating
system, motherboard drivers, usb interface cable are all normal; please uninstall the hardware in accordance with standard procedures,
so as not to damage the computer or camera. To avoid equipment damage, when you are ready to connect the device to your
computer, first the supplied data cable to the camera, then connect the other end of the data cable to your computer
!8, exception handling:
!Insufficient storage space camera will blink blue and red light at the same time about 5 seconds, automatically save the current
image file and shut down. If you want to continue to use the camera in the desired image file on the computer back up and delete the
memory of the old files to free up enough storage space;
!Camera battery is low margin, will turn blue light and red light flashes about 5 seconds, automatically save the current image file
and shut down. If you want to continue using the camera, charge the battery;
!Improper operation of the camera due to accidental or other special reason to stop responding, you can press the mode button
and open the key, to reset
!Parameter
