XTS BU1080PF-HDS User manual

User Manual
HD SBullet Camera
Thank you for purchasing our HDS camera. Please read this manual
carefully for correct use of the product and keep it for reference purposes.
Page 1 Page 2
Page 3
Warnings and Cautions
■Disclaimer
This manual may contain several technically incorrect places or printing
errors. The updates will be added into the new version of this manual.
The content is subject to change without notice.
■Avoid Electric Shock
To prevent electric shock, do not remove screws or cover.
■Avoid excessive moisture
Do not use strong or abrasive detergents when cleaning camera body.
Clean with dry cloth or mild detergent, wiping gently.
■Do not use camera beyond prescribed voltage range.
Only use included power supply. Ensure power input source conforms
to local voltage. Voltage outside of range could cause damage or
abnormal performance.
■Termly Inspection
A few parts of the device shall be replaced regularly due to their
average enduring time.
Use only under temperature conditions
between -40°C and +70°C.Provide
good ventilation whenusingin high
temperatureconditions.
Do not drop the camera or subject it to
physical shock.
It may cause production malfunction.
Strong light will degrade image quality
and could cause damage.
Do not aim camera at sun or extra
bright place.
Components and Accessories
Do not place the camera in extreme hot
or cold environment.
Overview
Connecting to Monitor
34
1
2 5
6
This series of the camera support varifocal lens and prime lens.
1
2
3
4
Power Cable
Fixed Ring
Mounting Base
VideoCable
5
6
Lens Cover
SunShield
HDMI
VGA
HDS DVR Monitor
VIDEO
Avoid touching the camera lens.
The lens is the most important
component of the camera. Be careful not
to smear it with fingerprints.
Page 4
■Never attempt to disassemble the camera privately.
It may result in internal components damaged.
Connecting to Power
Connect the adapter to the power input connector in accordance with the
camera. The recommended adapter specification for the camera is DC12V.
DC12V
Power
Drill Template
Camera
User Manual
Screws
XTS CORP - Headquarters
Product Development Dpt.
www.xtscorp.com
XTS CORP - Headquarters
Product Development Dpt.
www.xtscorp.com

1. Attach the drill template to the place where you want to fix the
camera and then drill3 screw holes and 1 cable hole ( if you want to
route the cables through the mounting base ) according to the drill
template.
2. Route the cables and connect the power cable and video cable.
3. Secure the mounting base with camera to the ceiling or wall with
screws as shown below.
4. Bracket adjustment. Before adjustment, preview the image of the
camera on a monitor and then loosen the fixed ring to adjust the
panning and tilting position of the camera. After you adjusted,
tighten the fixed ring.
* This installation should be made by a qualified service person and should
confirm to all local codes.
5. Remove the protection film softly to complete the installation.
Model
Image Sensor
Pixels
Signal System
Min. Illumination
Lens
IR Visible Distance
IP Rank
Video Out
Resolution
Frame Rate
ICR
DNR
S / N Ratio
Electronic Shutter
AGC
White Balance
Power
Temperature
Humidity
Dimension ( mm )
BU1080PF-HDS
1 / 3 '' CMOS
1920 x 1080
PAL / NTSC
0 Lux ( LED ON )
3.6 mm
10~20 m
IP66
BNC x 1
1080P ( 1920 x 1080 )
30 fps ( 60Hz ), 25 fps ( 50Hz )
Yes
Yes
> 52 dB ( AGC OFF )
Yes
Auto White Balance
DC12V ± 10%
- 40°C ~ 70°C
10%~ 90%
Ф x78 1 83
1 / 60s ~ 1 / 67500s
Page 8
Page 7
Page 6
Page 5
Before you start, please make sure that the wall or ceiling is strong enough to
withstand three times the weight of the camera.
*
Installation
Specications
Ceiling
Wall
90° Tilt
360° Pan
Installation
Features
This series of cameras adopt the latest HDS technology and advanced
circuit design, feature high definition and sensitivity, low noise and
distortion and support HD video transmission with the common coaxial
cable, ensuring the requirement of the HD monitoring in the traditional
surveillance system.
●High Transmission Performance
Real-time transmission with high speed and long distance.
●ICR Auto Switch
The filter will filter infrared light during the daytime and change to
normal at night to ensure a high sensitivity and clear image.
●Color-B/W Auto Switch
The camera will display color image in daytime and become
monochrome automatically at night.
●Auto White Balance
Adjustthe color temperature accordingto theenvironment
automatically.
●DNR
Reduce noise frombrighteness andcolorsignalto savestorage
roomunder low illumination condition.
●3-axis Adjustment
Adopt advanced 3-axis mechanism design to meet different mounting
requirement by flexibly adjusting the lens into the required angle.
●High Resolution
Adopt high performance HDS sensor, providing high definition a nd
clear image, up to 720P / 1080P resolution.
Correct Disposal of This Product
If the camera no longer functions or can no longer be repaired, it must be disposed
of according to regulations reading electronic waste. By not disposing of electronic
items in household waste you will not only be following the law, but contributing
the protection of the environment.
XTS CORP - Headquarters
Product Development Dpt.
www.xtscorp.com