XTS XTS-SD20XDN2MP-WIP Series User manual

asdasd
DDD8880
8880 NW 18th Terrace Doral, FL 33172 USA T: 1.305.863.7779 F: 1.305.863.7478 TollFree: 1.855.797.8XTS
Brasil: 55.11. 7561.1089 Colombia: 571.610.0843 Mexico: 52.55.917.2118
Intelligent Security Solutions
XTS-SD20XDN2MP-WIP Series
Quick Installation Guide
*Install IPScan on a Windows PC.
IPScan™ is a utility used to configure network settings for cameras & video servers. IPScan™ is available on the
CD-ROM.
Run Setup.exe to install IPScan.
* Camera Connections.
Displayed are the IO cable pin definitions.

asdasd
DDD8880
8880 NW 18th Terrace Doral, FL 33172 USA T: 1.305.863.7779 F: 1.305.863.7478 TollFree: 1.855.797.8XTS
Brasil: 55.11. 7561.1089 Colombia: 571.610.0843 Mexico: 52.55.917.2118
Intelligent Security Solutions
1 Package Contents
Along with the dome camera, contents include: RJ-45 in
line coupler
1 hex key and 1 star hex key
Optional Accessory: Power adapter (in bottom packaging)
2 Basic Installation
1. Connect the
CAT5e / 6 RJ-45 Ethernet cable to the camera; a
RJ-45 coupler is provided in
the packaging contents to
connect cable
to / from camera.
2. Connect Digital
I / O cables if applicable.
WARNING: Improperly
matching positive / negative cabling
will
cause operational problems and may damage the
camera or
I / O device.
3. Connect audio
in / out.
4. Before powering on the camera, loosen
the bolts on the
dome cover lid and remove
the protective camera
packaging.
WARNING: Powering on the
camera without removing
packaging may
damage the camera.
5. Insert the mini -SD card if applicable.
Remove the internal
black plastic cover, and slide
the mini-SD card into the SD
card
slot.
6. Replace dome cover
7. Insert the adapter power line (AC24V)
into the power
terminal block or plug the
RJ45 cable to a PoE+ switch for
60W output
at least.
The AC24V adaptor is an optional
accessory. Please order
before the product purchase is confirmed.
8. Connect the power adapter to the
camera’s power cable.
There is no power
button; recycling power restarts the camera.
Power can also be provided via
PoE+ (60W at least).
3 Bracket Installation
The camera has a collar which may need to
be removed to connect
the dome with a bracket.
This will depend on the bracket type used.
The collar has 2 screws which lock the collar
in place. Loosen the
screws, turn counter
clockwise and pull the collar up to remove.
The dome mounted on a pendant
bracket.

asdasd
DDD8880
8880 NW 18th Terrace Doral, FL 33172 USA T: 1.305.863.7779 F: 1.305.863.7478 TollFree: 1.855.797.8XTS
Brasil: 55.11. 7561.1089 Colombia: 571.610.0843 Mexico: 52.55.917.2118
Intelligent Security Solutions
4 Configure the Network Settings
The factory defaults IP address
settings:
IP Address
192.168.1.2
Subnet Mask
255.255.255.0
Gateway
192.168.1.1
Run IPScan
5 Access IP Camera Web Interface
When accessing an IP camera using the web interface for the first time (or when the IP
address changes), some configuration for ActiveX
controls are
required.
1. Open an IE browser
2. Type in the IP address in the URL: http://<IP ADDRESS> (e.g. http://10.1.21.53)
Pop-up windows and messages for
download / run Active X controls (examples below) will likely be displayed. Select
Install or Run to all such messages.

asdasd
DDD8880
8880 NW 18th Terrace Doral, FL 33172 USA T: 1.305.863.7779 F: 1.305.863.7478 TollFree: 1.855.797.8XTS
Brasil: 55.11. 7561.1089 Colombia: 571.610.0843 Mexico: 52.55.917.2118
Intelligent Security Solutions
Click on the add-on message, and choose Run
Add-on
Repeat the above until all ActiveX controls have been initiated. Once the process is complete, the
Live View will be displayed in IE.
6 Adding the Camera to an NVR System
Please refer to the NVR instructions and firmware User’s Manual for additional
details.
To add the 8180 to an NVR using RTSP protocol, specify the camera’s RTSP URL which will by
default be in the following format:
rtsp: // [ IP ADDRESS ] / rtpvideo1.sdp
7 Restoring Factory Default Settings
Restore the factory default settings via the camera’s web
UI:
The web UI Setup (System
-> Factory Default) ; network and user account data can be saved if desired. Please refer to the User’s
Manual for more information on the web UI Factory Default functionality.