PSR-1100/PSR-2100
16
16. Disassembling the Keyboard Assembly
16-1 Remove the Keyboard assembly. (See procedure 11.)
16-2 Remove the two (2) screws marked [30]. The MKS5F cir-
cuit board can then be removed. (Fig. 2)
* Be sure to make a correct match when connecting
MKS5F (CN1) and DM (CN102).
Connecting the connectors in the wrong way around
may cause damage to the MKS5F circuit board.
16-3 Remove the MK-L and MK-H circuit board while pressing
the fifteen (15)hooks A inward, and then remove the rub-
ber contact. (Fig. 11)
16-4 Remove the twenty-one (21) screws marked [140], then
removw the black keys from the lower notes. Afterwards,
remove the white keys DFA and C' and then remove the
white keys CEGB from the higer notes. At this time, lift
the keys from the front and slide them towards you. The
keys can then be removed from the assembly. (Fig. 12)
17. Assembling the Keyboard Assembly
17-1 Install the white keys CEGB from the lower notes, and then
install the DFAkeys and C' key.Afterwards install the black
keys from the higher notes, and tighten the twenty-one (21)
screws marked [140]. (Fig. 12)
17-2 Install the rubber contacts in the assembly while pressing
the keys as shown in Figure13. Check that the rubber con-
tact has been firmly placed into position in the area indi-
cated by the arrow in Figure 14. When fitting the rubber
contacts, raise both ends of the frame so that keys do not
push the rubber contact up.
17-3 Install the MK-L and MK-H circuit boards in the assembly
so that the hooks B hold it as shown in Figure 15.
[140]: Bind Head Tapping Screw-P 3.0x16 MFZN2BL (VB205200)
P
[140]: Bind Head Tapping Screw-P 3.0x16 MFZN2B (VS756700)
P Fig. 1212
MK-L MK-H
,
Hooks A
A
Black key
Black key
Rubber contact
White key
White key C'
C'
White key CEGB
CEGB
White key DFA
DFA
Fig. 1111
[140]
Hooks BB
Rubber contact Rubber contact
Fig. 1414
Fig. 1515
Fig. 1313
MK-L MK-H
,
16. 16M鍵盤 Ass'y の分解
16-1 16M 鍵盤 Ass'y を外します。(11 項 参照)
16-2 [30]のネジ 2 本を外し、MKS5F シートを外します。
(図 2)
16-3 MK-LシートとMK-Hシートを止めているフックA15
個を矢印の方向に押し外して、MK-LシートとMK-H
シートを外します。(図 11)
16-4 白鍵と黒鍵を止めている[140]のネジ21本を外し、黒
鍵を音程の低い方から外します。次に、白鍵DFA と
白鍵 C' を外し、最後に白鍵 CEGBを音程の高い方か
ら外します。このとき、鍵盤の手前を持ち上げ、手前
にスライドさせて取り外してください。(図 12)
17. 16M鍵盤 Ass'y の組立
17-1 白鍵CEGBを音程の低い方からはめ込みます。次に、
白鍵DFAと白鍵C'をはめ込みます。最後に黒鍵を音
程の高い方からはめ込み、白鍵と黒鍵を止めていた
[140]のネジ 21 本を取り付けます。(図 12)
17-2 接点ゴムは、図13のように鍵盤を押し上げながら、図
14 のようにしっかりとはめ込んで下さい。このとき、
鍵盤が接点ゴムを押し上げて接点ゴムが浮かないよう
に、MKフレームの両端を上げて作業を行って下さい。
17-3 MK-LシートとMK-Hシートは、図15のようにフック
B にはめ込んで取り付けます。