Yamaha FZR400 1988-1989 User manual

Yamaha
FZR400
Service
Manual
1988-1989 Models

CONTENTS
CHAPTER 1.
GENERAL INFORMATION
MOTORCYCLE IDENTIFICATION ................................ l-l
VEHICLE IDENTIFICATION NUMBER ......................... l-l
ENGINE SERIAL NUMBER................................... l-l
IMPORTANT INFORMATION. ..........................
....... l-2
PREPARATION FOR REMOVAL ..................... ....... l-2
ALL REPLACEMENT PARTS ........................ ....... l-2
GASKETS, OIL SEALS, AND O-RINGS ................ ....... l-2
LOCK WASHERS/PLATES AND COTTER PINS ......... ....... l-3
BEARINGS AND OIL SEALS ........................ ....... l-3
CIRCLIPS ........................................ ....... l-3
SPECIAL TOOLS. ............................................. l-4
FOR TUNE UP .............................................
1-4
FOR ENGINE SERVICE .....................................
l-5
FOR CHASSIS SERVICE .....................................
1-B
FOR ELECTRICAL COMPONENTS ............................ l-9
CHAPTER 2.
SPECIFICATIONS
SPECIFICATIONS ............................................. 2-l
GENERAL SPECIFICATIONS ................................. 2-l
MAINTENANCE SPECIFICATIONS ............................
2-4
ENGINE................................................2- 4
CHASSIS...............................................2-11
ELECTRICAL ..........................................
.2-14
GENERAL TORQUE SPECIFICATIONS. .......................
.2-16
DEFINITION OF UNITS ..................................... 2-16
LUBRICATION POINT AND GRADE OF LUBRICANT.............
2-17
LUBRICATION DIAGRAM. . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
. . . . . . . . . . . . . . . . . . . . . . . . . .
2-20
COOLANT DIAGRAM ................
CABLE ROUTING .................................
. . . . . . . . . . . .
2-21

CHAPTER 3.
PERIODIC INSPECTION AND ADJUSTMENT
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 3-1
MAINTENANCE INTERVALS CHART .............................
.3-l
PERIODIC MAINTENANCE EMISSION CONTROL SYSTEM ........
.3-l
GENERAL MAINTENANCE/LUBRICATION ..................... .3-2
COWLING REMOVAL AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . .3-4
ENGINE .....................................................
3-7
EXUP CABLE ADJUSTMENT (For California only) ................
3-7
VALVE CLEARANCE ADJUSTMENT ..........................
3-8
CARBURETOR SYNCHRONIZATION .......................... 3-15
IDLE SPEED ADJUSTMENT ..................................
3-17
THROTTLE CABLE FREE PLAY ADJUSTMENT .................
3-18
SPARK PLUG INSPECTION ..................................
3-19
IGNITION TIMING CHECK ................................... 3-20
COMPRESSION PRESSURE MEASUREMENT ....................
3-21
ENGINE OIL LEVEL INSPECTION ............................. 3-23
ENGINE OIL REPLACEMENT ................................ 3-23
ENGINE OIL FILTER REPLACEMENT ......................... 3-24
CLUTCH ADJUSTMENT. .................................... 3-26
AIR FILTER CLEANING.....................................
3-27
CARBURETOR JOINT INSPECTION ...........................
3-27
FUEL LINE INSPECTION ....................................
3-27
CRANKCASE VENTILATION HOSE INSPECTION ................ 3-28
EXHAUST SYSTEM INSPECTION ............................. 3-28
COOLANT LEVEL INSPECTION ..............................
3-29
COOLANT REPLACEMENT ..................................
3-29
CHASSIS ...... . .............................................. 3-32
FRONT BRAKE ADJUSTMENT ............................... 3-32
REAR BRAKE ADJUSTMENT ................................ 3-32
BRAKE FLUID INSPECTION ................................. 3-33
BRAKE PAD INSPECTION ................................... 3-33
REAR BRAKE LIGHT SWITCH ADJUSTMENT. .................. 3-33
BRAKE HOSE INSPECTION .................................. 3-34
AIR BLEEDlNG............................................3-3 4
DRIVE CHAIN SLACK ADJUSTMENT .......................... 3-35
DRIVE CHAIN LUBRICATION ................................
3-37
STEERING HEAD INSPECTION ...............................
3-37
FRONT FORK INSPECTION .................................. 3-40
REAR SHOCK ABSORBER ADJUSTMENT ...................... 3-40
TIRE INSPECTION ......................................... 3-41
WHEEL INSPECTION ....................................... 3-42
CABLE INSPECTION ........................................ 3-43
LUBRICATION ............................................ 3-43

ELECTRICAL. ................................................ 3-44
BATTERY INSPECTION ..................................... 3-44
FUSE INSPECTION ......................................... 3-46
HEADLIGHT BEAM ADJUSTMENT ............................ 3-46
HEADLIGHT BULB REPLACEMENT ........................... 3-47
TAIL/BRAKE BULB REPLACEMENT .......................... 3-48
CHAPTER 4.
ENGINE OVERHAUL
ENGINE REMOVAL ........................................... .4-l
LOWER COWLING, CENTER COWLING,
UPPER COWLING AND TOP COVER. ......................... .4-l
FUEL TANK............................................... .4-l
ENGINEOIL.. ................................. ..~.........4- 1
COOLANT.................................................4- 1
AIR FILTER CASE AND CARBURETOR., ...................... .4-l
RADIATOR................................................4- 2
MUFFLER ASSEMBLY ...................................... .4-2
CLUTCH CABLE AND DRIVE CHAIN .......................... .4-4
LEADS....................................................4- 4
ENGINE REMOVAL ........................................ .4-5
ENGINE DISASSEMBLY ........................................ .4-7
CYLINDER HEAD COVER, CAMSHAFT AND
CYLINDER HEAD ......................................... .4-7
CYLINDER AND PISTON ................................... .4-10
STARTER CLUTCH ........................................ .4-12
CLUTCH..................................................4-13
A.C. MAGNETO ........................................... .4-14
WATER PUMP ............................................ .4-15
OIL PUMP AND SHIFT SHAFT............................... .4-16
OIL PAN AND OIL STRAINER. .............................. .4-17
STARTER MOTOR ......................................... 4-18
CRANKCASE DISASSEMBLY ................................. 4-18
TRANSMISSION, SHIFTER AND SHIFT CAM. ................... 4-19
CRANKSHAFT ............................................. 4-20
VALVE PAD AND VALVE ................................... 4-21
CONNECTING ROD......................................... 4-23
INNER ROTOR (OIL PUMP). ................................. 4-23
INSPECTION AND REPAIR ..................................... 4-24
CYLINDER HEAD .............................
,
............ 4-24
VALVE...................................................4-2 5
VALVE GUIDE I:.
................................. .4-26........
VALVE SEAT. ............................................ .4-27
VALVE SPRING........................................... .4-30
VALVE LIFTER ........................................... .4-31
CAMSHAFT, CAM CHAIN AND CAM SPROCKET................ .4-31
CYLINDER AND PISTON ................................... .4-33

PISTON RING AND PISTON PIN .............................. 4-35
CRANKSHAFT AND CONNECTING ROD .......................
4-37
OlLPUMP.................................................4-4 1
PRlMARYDRlVE..........................................4-4 2
STARTER CLUTCH ........................................ .4-43
CLUTCH..................................................4-4 4
TRANSMISSION .......................................... .4-46
RELIEF VALVE AND PIPE .................................. .4-47
CRANKCASE ............................................. .4-47
BEARING AND OIL SEAL ..................................
.4-47
YAMAHA EXHAUST VARIABLE VALVE (For California only) ..... .4-48
ENGINE ASSEMBLY AND ADJUSTMENT. ........................ .4-49
INNER ROTOR (OIL PUMP). ................................ .4-49
CONNECTING ROD. ....................................... .4-49
CRANKSHAFT ............................................
.4-50
VALVE PAD AND VALVE .................................. .4-51
CRANKCASE ............................................. .4-54
TRANSMISSION .......................................... .4-55
TRANSMISSION, SHIFTER AND SHIFT CAM ................... .4-56
CRANKCASE ASSEMBLY ................................... .4-57
STARTER MOTOR ........................................ .4-59
OIL PAN AND OILSTRAINER ............................... .4-59
OIL PUMP AND SHIFT SHAFT. .............................. .4-60
A.C. MAGNETO ........................................... .4-61
CLUTCH..................................................4-6 3
STARTER CLUTCH ........................................ .4-65
PISTON AND CYLINDER ................................... .4-67
CYLINDER HEAD AND CAMSHAFT .......................... .4-70
CAM CHAIN TENSIONER ................................... .4-75
REMOUNTING ENGINE .................................... .4-76
YAMAHA EXHAUST VARIABLE VALVE (For California only) ......4-78

CHAPTER 5.
COOLING SYSTEM
RADlATOR...................................................5- 1
REMOVAL.................................................5- 2
INSPECTION...............................................5- 3
INSTALLATION ........................................... .5-4
WATER PUMP AND THERMOSTATIC VALVE. ......................
5-6
REMOVAL.................................................5- 7
lNSPECTlON...............................................5- 9
INSTALLATION .......................................... .5-10
CHAPTER 6.
CARBURETOR
CARBURETOR ...............................................
6-l
SECTIONVIEW ............................................
6-2
REMOVAL ................................................ 6-3
DISASSEMBLY ............................................ 6-5
INSPECTION .............................................. 6-6
ASSEMBLY.. .............................................
6-B
INSTALLATION ...........................................
6-9
,:
i;
ADJUSTMENT .............................................
6-10
CHAPTER 7.
CHASSIS
FRONT WHEEL. .............................................. 7-l
REMOVAL ................................................
7-2
INSPECTION ..............................................
7-2
INSTALLATION ........................................... 7-4
REAR WHEEL ................................................
7-7
REMOVAL ................................................
7-B
INSPECTION ..............................................
7-B
INSTALLATION ...........................................
7-9

FRONT AND REAR BRAKE. ................................... .7-10
BRAKE PAD REPLACEMENT................................ .7-12
CALIPER DISASSEMBLY ................................... .7-16
MASTER CYLINDER DISASSEMBLY ......................... .7-18
INSPECTION AND REPAIR ................................. .7-19
ASSEMBLY ...............................................
7-21
FRONT FORK ...............................................
.7-28
REMOVAL................................................7-2 9
DISASSEMBLY ............................................ 7-30
lNSPECTlON..............................................7-3 1
ASSEMBLY ............................................... 7-32
INSTALLATION ........................................... 7-34
STEERING HEAD AND HANDLEBAR. ............................. 7-36
REMOVAL................................................7-3 8
lNSPECTlON..............................................7-4 1
INSTALLATION ........................................... 7-42
REAR SHOCK ABSORBER AND SWINGARM
.......................
7-47
HANDLING NOTES ......................................... 7-49
DISPOSAL NOTES. ......................................... 7-49
REMOVAL................................................7-4 9
lNSPECTlON..............................................7-5 2
INSTALLATION ........................................... 7-54
DRIVE CHAIN AND SPROCKET ................................. 7-56
REMOVAL................................................7-5 6
INSPECTION AND CLEANING ................................ 7-56
INSTALL’ATION ........................................... 7-57

CHAPTER 8.
ELECTRICAL
FZR400U/SUC CIRCUIT DIAGRAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1
ELECTRICAL COMPONENTS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
CHECKING OF SWITCHES. ..................................... .8-5
SWITCH CONNECTION AS SHOWN IN MANUAL .................
.8-5
CHECKING SWITCH FOR TERMINAL CONNECTION ............. .8-5
CHECKING OF BULBS ......................................... .8-8
KINDS OF BULBS .......................................... .8-8
CHECKING BULB CONDITION ...............................
.8-8
IGNITION SYSTEM. ...........................................
8-l 1
Cl RCUIT DIAGRAM ........................................
8-11
DIGITAL IGNITION CONTROL SYSTEM DESCRIPTION ........... 8-13
OPERATION ............................................ ..8-13
TROUBLESHOOTING ....................................... 8-14
ELECTRIC STARTING SYSTEM. .................................
8-21
CIRCUIT DIAGRAM ........................................
8-21
STARTING CIRCUIT OPERATION ............................. 8-23
TROUBLESHOOTING. ...................................... 8-24
STARTER MOTOR ......................................... 8-30
CHARGING SYSTEM. .......................................... 8-33
CIRCUITDIAGRAM.. .................................... ..8-3 3
TROUBLESHOOTING ....................................... 8-35
LIGHTING SYSTEM ........................................... 8-39
CIRCUIT DIAGRAM ........................................ 8-39
TROUBLESHOOTING .......................................
8-41
LIGHTING SYSTEM CHECK .................................. 8-44
SIGNALSYSTEM ..............................................
8-49
CIRCUIT DIAGRAM ........................................ 8-49
TROUBLESHOOTING .......................................
8-51
SIGNAL SYSTEM CHECK. ................................... 8-53
COOLING SYSTEM. ........................................... 8-69
Cl RCUIT DIAGRAM ........................................
8-69
TROUBLESHOOTING .......................................
8-71
FUELSYSTEM................................................8.7 5
CIRCUIT DIAGRAM .......................................
.8-75
FUEL PUMP CIRCUIT OPERATION ............................
8.77
TROUBLESHOOTING .......................................
8-78
FUEL PUMP TEST. ........................................
.8-82

YAMAHA EXHAUST VARIABLE VALVE SYSTEM
(For California only). ......................................... .8-83
CIRCUIT DIAGRAM ....................................... .8-83
TROUBLESHOOTING ...................................... .8-85
METER ASSEMBLY........................................... .8-89
REMOVAL................................................8-9 0
INSTALLATION ...........................................
8-91
CHAPTER 9.
TROUBLESHOOTING
STARTING FAILURE/HARD STARTING. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-l
POOR IDLE SPEED PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
POOR MEDIUM AND HIGH SPEED PERFORMANCE.. . . . . . . . . . . . . . . . . 9-4
FAULTY GEAR SHIFTING.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
CLUTCH SLIPPING/DRAGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
OVERHEATING OR OVER-COOLING.. . . . . . . . . . I.. . . . . . . . . . . . . . . . . 9-6
FAULTY BRAKE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . _. . . . 9-7
FRONT FORK OIL LEAKAGE/MALFUNCTION.. . . . . . . . . . . . . . . . . . . . . 9-7
INSTABLE HANDLING.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
FAULTY SIGNALS AND LIGHTS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
FAULTY EXUP (For California only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-l 0

CONTENTS
GENERAL INFORMATION .......................................
1
MOTORCYCLE IDENTIFICATION .............................. 1
VEHICLE IDENTIFICATION NUMBER ........................
1
ENGINE SERIAL NUMBER ................................. 1
SPECIFICATIONS ............................................... 2
GENERAL SPECIFICATIONS .................................. 2
MAINTENANCE SPECIFICATIONS .............................. 3
CHASSIS ................................................ 3
TIGHTENING TORQUE .................................... 4
GENERAL TORQUE SPECIFICATIONS .......................... 5
PERIODIC INSPECTIONS AND ADJUSTMENTS ...................... 6
CHASSIS
...................................................
6
DRIVE CHAIN SLACK ADJUSTMENT........................ 6
CHASSIS ...................................................... 8
REARWHEEL ............................................... 8
REMOVAL .............................................. 9
INSPECTION ............................................ 10
INSTALLATION ......................................... 10
STATIC WHEEL BALANCE ADJUSTMENT ...................
11
FRONT AND REAR BRAKE .................................. 12
BRAKE PAD REPLACEMENT .............................. 14
CALIPER DISASSEMBLY .................................. 19
MASTER CYLINDER DISASSEMBLY ........................
21
INSPECTION AND REPAIR ................................ 23
ASSEMBLY.. ........................................... 26

MOTORCYCLE IDENTIFICATION
GENERAL
INFORMATION
MOTORCYCLE IDENTIFICATION
VEHICLE IDENTIFICATION NUMBER
The vehicle identification number @ is stemped
into the right side of the steering head.
Starting serial number:
FZR400A (Except for California):
JYA3BFEO * LA012101
FZR400SAC (For California):
I
JYASFHCO * LA003101
J
NOTE:
The vehicle identification number is used to
identify your motorcycle and may be used to
register your motorcycle with the licensing
authority in your state.
ENGINE SERIAL NUMBER
The engine serial number @ is stamped into the
right side of the engine.
Starting serial number:
FZR400A (Except for California):
3BF-012101
FZR400SAC (For California):
I
3FH-003101
1
NOTE:
@The first three digits of these numbers are for
model identifications; the remaining digits are
the unit production number.
@Designs and specifications are subject to
change without notice.
FZRIQOOA FZ R400SAC

GENERAL SPECIFICATIONS
JSPECII
SPECIFICATIONS
GENERAL SPECIFICATIONS
Model
Model Code Number:
Vehicle Identification Number:
Engine Starting Number:
Basic Weight:
With Oil and Full Fuel Tank
Tire:
Type
Size
Manufacture (Type)
FZR400A/FZR400SAC
3BF5 (FZR400A)
3FH3 (FZR400SAC)
JYA3BFEO -X LA012101 (FZR400A)
JYA3FHCO +X- LA003101 (FZR400SAC)
3BF-012101 (FZR400A)
3FH-003101 (FZR400SAC)
188 kg (414 lb) (FZR400A)
191 kg (421 lb) (FZR400SAC)
Front Rear
Tubeless Tubeless
110/70R17-54H 140/60R 1 B-64H
BRIDGESTONE BRIDGESTONE
(CYl5) (CY16)
DUNLOP DUNLOP
(K5lOF) (K510)
-2-

MAINTENANCE SPECIFICATIONS pqq
MAINTENANCE SPECIFICATIONS
CHASSIS
Model FZR400A/FZR400SAC
Front Suspension:
Front Fork Travel 130 mm (5.12 in)
Front Spring Free Length 412 mm (16.2 in)
< Limit >408 mm (16.1 in)
Collar Length 160 mm (6.3 in)
Spring Rate: Kl
4.4 N/mm (0.5 kg/mm, 25.2 lb/in)
K2 6.6 N/mm (0.7 kg/mm, 37.5
lb/in)
Stroke Kl
0.0 - 90 mm (0.0 - 3.54 in)
K2 90
- 130 mm (3.54 - 5.12 in)
Optional Spring No
Oil Capacity 440
cm3 (15.5 Imp 02, 14.9 US oz)
Oil Level (Fully Compression) 92 mm (3.62 in)
Bellow the top of inner fork tube without
fork spring
Oil Grade Yamaha Fork Oil 10WT or equivalent
Front Disc Brake:
Type
Dual
Disc Outside Diameter x Thickness 282 x 4 mm (11
.lO x 0.16 in)
Pad Thickness Inner 5.5 mm (0.22 in)
< Limit >* 0.5 mm (0.02 in)
Pad Thickness Outer 5.5 mm (0.22 in)
< Limit >* 0.5 mm (0.02 in)
4
.: ‘.I. . ., ‘,‘;:.‘;. . ;. .;:
*
Master Cylinder Inside Diameter 15.87 mm (0.62
in)
Caliper Cylinder Inside Diameter 32.10 mm (1.26 in)
Brake Fluid Type
DOT#4or DOT#3
-3-

MAINTENANCE SPECIFICATIONS
-1
TIGHTENING TORQUE
Part to be tightened
Front Axle and Outer Tube
Rear Axle and Nut
Handlebar Crown and Inner Tube
Handlebar Crown and Steering Stem
Brake Caliper (Front/Rear)
Bleed Screw and Brake Caliper
Brake Hose and Union Bolt
Front Master Cylinder and Master Cylinder Holder
Front Master Cylinder and Cylinder Cap
Front Fender and Outer Tube
Handlebar and Inner Tube
Engine Mounting: Front
Rear - Upper
Rear - Lower
Down Tube and Frame: Front
Rear
Footrest Bracket and Frame
Pivot Axle and Nut
Relay Arm and Frame
Arm and Swingarm
Arm and Relay Arm
Rear Shock Absorber and Relay Arm
Rear Shock Absorber and Frame
Footrest and Footrest Bracket
Rear Footrest Bracket and Frame
Rear Master Cylinder and Rear Arm Bracket
Cowling and Stay
Compression Bar and Brake Caliper Bracket
Front Fork Pinch Bolt
Sprocket and Clutch Hub
Brake Disc and Clutch Hub
Inner Tube and Steering Stem
Frame and Rear Frame: Upper
Lower
Thread size
-
MI4x I.5
Ml6 x 1.5
M8 x I.25
M22 x 1.0
MIOx 1.25
M8 x 1.25
MIOx 1.25
M6 x 1.0
M5 x 0.8
M6 x 1.0
M8 x 1.25
MlOx 1.25
MlOx 1.25
M8 x 1.25
MlOx I.25
M8 x 1.25
Ml0 x 1.25
Ml4x 1.5
MIOx 1.25
Ml0 x 1.25
MlOx I.25
MIOx I.25
Ml0 x 1.25
Ml0 x 1.25
M8 x 1.25
M8 x I.25
M6 x 1.0
M8 x I.25
M8 x I.25
M8 x I.25
M8 x 1.25
M8 x I.25
MlOx 1.25
Ml2 x 1.25
-r
Tightening torque
T\
Nm ma kg
ft. lb
58 5.8 42
107 10.7 77
26 2.6
19
110 11.0 80
35 3.5 25
6 0.6 4.3
26 2.6
19
9 0.9 6.5
2 0.2 1.4
6 0.6 4.3
23 2.3
17
55 5.5 40
55 5.5 40
45 4.5 32
60 6.0 43
33 3.3 24
33 3.3 24
90 9.0 65
40 4.0 29
40 4.0 29
40 4.0 29
40 4.0 29
40 4.0 29
57 5.7 41
20 2.0 I4
20 2.0 I4
4 0.4 2.9
23 2.3 17
20 2.0
14
32 3.2 23
20 2.0 14
22 2.2 16
64 6.4 46
88 8.8 64
-4-

GENERAL TORQUE SPECIFICATIONS
Is4 P9l
GENERAL
TORQUE SPECI
FICA-
TIONS
This chart specifies torque for standard fasteners
with standard I.S.O. pitch threads. Torque
specifications for special components or assem-
blies are included in the applicable sections of
this book. To avoid warpage, tighten multi-
fastener assemblies in a crisscross fashion, in
progressive stages, until full torque is reached.
Unless otherwise specified, torque specifications
call for clean, dry threads. Components should
be at room temperature.
A: Distance across flats
6: Outside thread diameter
DEFINITION OF UNITS
Unit
Read
mm
millimeter
cm
centimeter
kg
kilogram
N Newton
Nm Newton meter
mskg Meter kilogram
Pa Pascal
N/mm Newton per millimeter
L
Liter
cm3 Cubic centimeter
r/min Revolution per minute
Definition
10e3 meter
IO-* meter
lo3 gram
1 kg x m/set*
Nxm
m x kg
N/m2
N/mm
Measure
Length
Length
Weight
Force
Torque
Torque
Pressure
Spring rate
Volume or Capacity
Engine Speed
-5-

DRIVE CHAIN SLACK ADJUSTMENT
PERIODIC INSPECTIONS
AND ADJUSTMENTS
CHASSIS
DRIVE CHAIN SLACK ADJUSTMENT
NOTE:
Before checking and/or adjusting the chain slack,
rotate the rear wheel several revolutions. Check
the chain slack several times to find the point
where the chain is the tightest. Check and/or
adjust the chain slack where the rear wheel is in
this “tight chain” position.
Too little of chain slack will overload the engine
and over vital parts; keep the slack within the
specified limits.
Securely support the motorcycle so there is
no danger of it falling over.
1. Place the motorcycle on a level place, and
hold it in an upright position.
2. Check:
?? Drive chain slack @
Out of specification + Adjust.
>
3. Adjust:
?? Drive chain slack
Adjustment steps:
?? Remove the cotter pin @ .
?? Loosen the axle nut @ .
?? Loosen both locknuts @ (adjuster) and
turn the adjuster @ clockwise or counter-
clockwise until the specified slack is
obtained.
-6-
.

DRIVE CHAIN SLACK ADJUSTMENT ADJ m
I1NspI(
Clockwise
+ Slack is increased.
Counterclockwise --, Slack is decreased.
NOTE:
Turn each adjuster exactly the same amount
to maintain correct axle alignment. (There are
marks on each side of swingarm; use them to
check for proper alignment.)
?? Tighten the locknut.
?? Tighten the axle nut to specification, while
pushing up or down on the chain to zero
slack.
107 Nm (10.7 m- kg, 77 ft. lb)
?? Install the cotter pin.
Always use a new cotter pin on the axle nut.
Do not loosen the axle nut after torque
tightening. If the axle nut groove is not
aligned with the cotter pin hole, align groove
rnrith the hole by tightening up on the axle
nut.
-7-

REAR WHEEL
-1
CHASSIS
REAR WHEEL
@Collar
@ Oil seal
@ Bearing
@ Spacer
@ Clutch hub
@Collar
@ Cotter pin
@ Tension bar
WEAR LIMIT:
1 .O mm (0.04 in)
140160R 18-64H
RIM SIZE:
MT4.00 x 18
RIM RUNOUT LIMIT:
RADIAL:
2.0 mm (0.08 in)
LATERAL:
I
-8-

REAR WHEEL
-1
REMOVAL
1. Place the motorcycle on a level place.
Securely support the motorcycle so there is no
danger of it falling over.
2. Elevate the rear wheel by placing a suitable
stand under the swingarm.
3. Remove:
?? Bolts (brake caliper) @
NOTE:
Do not depress the brake pedal while the caliper
is removed.
4. Loosen:
?? Locknut @
?? Adjuster @
5. Remove:
?? Cotter pin @I
*Axle nut @I
?? Washer @
6. Push the rear wheel forward and disconnect
the drive chain @ from the driven sprocket
0
7. Remove:
?? Rear wheel axle
?? Adjuster collars (left and right)
?? Rear wheel @
8. Remove:
?? Collar (left and right)
-9-