YesCam Yes737 User manual

Yes737
All-in-one
Mega-pixel Pan/tilt
IP Network Camera
User Manual
Date: 2015/01/21
For firmware version v030702

Yes737 Mega-pixel Pan/Tilt IP Camera
2
Table of Contents
1. INTRODUCTION..........................................................................................................................6
2. HARDWARE DESCRIPTION AND QUICK INSTALLATION/USAGE ................................8
2.1. MAJOR HARDWARE COMPONENTS.......................................................................................8
2.2. QUICK INSTALLATION AND USAGE ......................................................................................10
2.3. WIRELESS CONNECTION (IF ROUTER/AP HAS WPS BUTTON)..........................................15
2.4. WIRELESS CONNECTION (IF WPS NOT SUPPORTED ON ROUTER/AP)..............................15
2.5. PUSH NOTIFICATION ............................................................................................................16
3.1. INFORMATION ......................................................................................................................19
3.2. NETWORK............................................................................................................................20
3.3. WIFI SECURITY....................................................................................................................22
3.4. ADVANCED NETWORK.........................................................................................................25
3.5. VIDEO SETTINGS .................................................................................................................26
3.6. MOBILE VIDEO SETTINGS....................................................................................................28
3.7. NIGHT MODE CONTROL .......................................................................................................28
3.8. EMAIL/FTP ALARM...............................................................................................................29
3.9. SPEAKER ALARM SETTINGS ...............................................................................................33
3.10. NAS SETTINGS....................................................................................................................33
3.11. CLOUD STORAGE SETTINGS...............................................................................................35
3.12. SD-CARD SETTINGS ...........................................................................................................37
3.13. INFRARED THERMOMETER ..................................................................................................39
3.14. SCHEDULING .......................................................................................................................39
3.15. LED DISPLAY CONTROL.....................................................................................................42
3.16. DATE/TIME...........................................................................................................................43
3.17. ADMIN..................................................................................................................................44
3.18. UPGRADE ............................................................................................................................45
3.19.REBOOT...............................................................................................................................47
3.20. SET TO FACTORY DEFAULT..................................................................................................48
4. FEATURES AND SPECIFICATIONS......................................................................................49
4.1. FEATURES ...........................................................................................................................49
4.2. SPECIFICATIONS..................................................................................................................50
5. PACKAGE CONTENTS............................................................................................................53
APPENDIX A. LIST OF TESTED NAT/ROUTER DEVICES........................................................54
APPENDIX B. MAXIMUM ALLOWED VIDEO USERS.................................................................55

Yes737 Mega-pixel Pan/Tilt IP Camera
3
APPENDIX C. PERFORMANCE INFORMATION .........................................................................56
APPENDIX D. TROUBLE SHOOTING............................................................................................58
APPENDIX E. THIRD PARTY AND EMBEDDED WEB PAGE INTEGRATION .......................60
APPENDIX F. SNAPSHOT PICTURE ON ANY BROWSER........................................................61

Yes737 Mega-pixel Pan/Tilt IP Camera
4
List of Figures and Tables
Figure 2-1: Major components in the front panel
Figure 2-2: Major components in the back panel
Figure 2-3: IP CAM connection diagram.
Figure 2-4: Connect Ethernet cable to a switch/router.
Figure 2-5: The installation CD disk
Figure 2-6: The ID/Password card
Figure 2-7: Running window of YesCam View program
Figure 2-8: Pop-up play-video password window
Figure 2-9: Unplug the Ethernet cable to enable the WiFi function
Figure 3-1: Open the web configuration page from YesCam View software
Figure 3-2: IP CAM Web configuration login page
Figure 3-3: IP CAM Information page
Figure 3-4: Network settings page for DHCP function
Figure 3-5: Network settings page for fixed IP address
Figure 3-6: WiFi security disabled page
Figure 3-7: WiFi security enabled page
Figure 3-8: WiFi testing page
Figure 3-9: Advanced network settings page
Figure 3-10: Video settings page
Figure 3-11: Mobile video settings page
Figure 3-12: Night mode control page
Figure 3-13: Email/FTPAlarm page
Figure 3-14: SMTP server settings page
Figure 3-15: Speaker Alarm Settings page
Figure 3-16: NAS Storage Settings page
Figure 3-17: Cloud Storage Settings page
Figure 3-18: SD-Card Settings page
Figure 3-19: SD-Card information page
Figure 3-20: Infrared thermometer settings page
Figure 3-21: Schedule management page
Figure 3-22: Led Control settings page
Figure 3-23: System date/time settings page
Figure 3-24: Admin settings page
Figure 3-25: Firmware upgrade settings page
Figure 3-26: Firmware upgrade status page
Figure 3-27: System reboot settings page

Yes737 Mega-pixel Pan/Tilt IP Camera
5
Figure 3-28: System reboot under-going page
Figure 3-29: Stick on the reset button to set to the factory default
Figure 5-1: The IP camera body
Figure 5-2: Power Adaptor
Figure 5-3: Quick installation guide
Figure 5-4: Ethernet cable
Figure 5-5: Installation CD
Figure 5-6: ID/Password Card
Figure 5-7: Warranty card
Table A-1: List of tested Wireless AP/router devices
Table A-2: List of tested Wired NAT/router devices

Yes737 Mega-pixel Pan/Tilt IP Camera
6
1. Introduction
The IP Camera is designed for all day video surveillance on your iPhone/iPad
and Android mobiles/pads. The setup is truly 1-2-3 :
1. Connect the camera to the network
2. Download the app YesCam View into your iPhone/iPad or Android
3. View video by the camera ID/password
The push notification is supported, so that you will get the notification from your
iPhone/iPad and Android once there is any events detected through the PIR body
sensor or sound detector on the camera, even when your mobile is on sleep mode.
The pan/tilt functions allow the mobile user to pan./tilt the camera through a
finger move on the mobile screen. You could monitor the whole room with a single
camera.
The SD card recording is supported, and you could playback the recorded video
on your iPhone/iPad and Android. You could also do the SD card recording only when
there is PIR or sound detection to save the SD card storage size. The PIR and sound
detected recording has a 5 seconds pre-recording, so that you will always catch the
critical moment.
The NAS and cloud storage is supported. You can record the video files into any
normal NAS devices or to your Dropbox account. And you can playback those
recorded video files remotely on your mobile devices or computers.
For day & night usage, there are two video sensors/lens on the camera, one for
day and one for night. The day lens and night lens focus are separately tuned for day
light and Infra Red light for best video quality. No ICR, no mechanical problem.
Two-way audio is supported. You can monitor the synchronized video/audio and
talk to or warn the people around the camera from your iPhone/iPad and Android once
you got the push notification. There is a built-in speaker and a speaker jack is
provided so that you could connect any high power speaker to the camera for your
needs.
The WPS(WiFi Protected Setup) is supported. You could set up the WiFi

Yes737 Mega-pixel Pan/Tilt IP Camera
7
connection of the camera with the router by clicking the WPS button on the camera
and on the router at the same time. No more complicated WiFi configuration.
An infrared thermometer is provided. You could monitor the temperature of the
environment of the camera.And you could setup the camera to trigger alarm when the
environment temperature is out of a specified range.
The IP camera is ideal for securing small businesses, home offices and
residences. The IP Camera is a perfect replacement of the alarm system and baby
monitor in your house and shop. .
The differences
It’s very easy to see the video of the Pan/Tilt IP Camera, you only need to key in
the ID/Password of the IP CAM any where in the world, you do not need to remember
the IP address or domain name or DDNS name or port number. And you do not need
to modify the settings(like port mapping, fixed IP, DDNS, virtual server) of the
NAT/router devices, it’s just a plug & play usage.
So, the differences are the followings:
Public IP address needed ? No
Dynamic DNS needed ? No
Port mapping in router? No
Virtual server in router ? No
UPnP support in router ? No
What’s needed ? ID and Password

Yes737 Mega-pixel Pan/Tilt IP Camera
8
2. Hardware description and quick installation/usage
The IP CAM is designed to be very easy to install and use. First, let’s see the
major components of the IP CAM products.
2.1. Major hardware components.
The major components on the front panel of the IP CAM products are the
followings :
1. Lens –the lens is inside the mask and the focus of the lens is fixed, you do not
need to spend time to adjust the focus, the effective focus range is from 30cm to
infinity.
2. IR LED –there are two IR LEDs for the night mode usage.
3. PIR –passive infrared sensor for body detection
4. Microphone –for receiving the audio/voice. Effective distance is about 5 meters.
5. Thermometer –for measuring the environment temperature and alarm if out of
some temperature range.
6. Status indication LED (red) –this LED is to indicate the Internet connection status.
When the Internet connection is connected, the LED will be constant red light. If
there is any Internet connection problem, the LED will be blinking red light.
7. Ethernet indication LED (blue) –this LED is to indicate if the Ethernet link is ok
and packet traffic is sending/receiving. When the Ethernet cable is connected, the
LED is constant blue light. When there is packet sending/receiving, the LED is
blinking blue light.
8. SD card LED –for the indication of the SD card activity( recording ).
9. Micro-SD card slot –for inserting the micro SD-Card. (support up to 32G bytes)
10. Internal speaker –there is an internal speaker inside.
11. External speaker jack –for connecting external speaker.
12. WPS button –for the setup of the WiFi connection with WPS function.
13. Light detector –for switching between day time and night time automatically.

Yes737 Mega-pixel Pan/Tilt IP Camera
9
Figure 2-1: Major components in the front panel
The major components on the back panel and bottom of the IP CAM products are
the followings:
1. Bracket screw jack –this is the position to screw in the bracket of the IP CAM.
With the bracket, you can put the IP CAM on the desk, on the wall or on the ceiling.
(Bracket not provided)
2. Power jack –this is the place to plug in the power adaptor. The power needed for
this IP CAM is 12V/1.0A, please make sure you are using the correct power
adaptor.
3. Ethernet jack –this is the place to plug in the RJ45 Ethernet cable. When the
Ethernet link is ok, the Ethernet indication LED on the front side will be blue light.
4. Reset button –this is the button to reset the IP CAM to default factory settings.
You need to use a small stick like pencil or tooth stick to press the reset button for
more than 3 seconds to enable the reset function. Usually when you forgot the
administrator account, you will probably need to do this reset action to reset to the
default factory settings. Please refer to section 3.19 for more details.
5. Wall mount –this is the place to hang the IP CAM on the ceiling or on the wall.
6. Antenna –this is the 802/11 n wireless antenna.

Yes737 Mega-pixel Pan/Tilt IP Camera
10
Figure 2-2: Major components in the back panel
2.2. Quick installation and usage
There are only three things that you need to do to see the video from the IP CAM.
1. Connect the IP CAM to the home/office network.
2. Install the YesCam View/app software on the notebook/PC/mobiles.
3. Key in the ID/password of the IP CAM(from the ID/Password card) on the YesCam
View, and then you can see the video.
First, Connect the IP CAM to the home/office network
Please connect the IP CAM accessaries to the IP CAM body correctly, including the
power adapter and Ethernet cable, as shown in Figure 2-3. And connect the other end
of the Ethernet cable to the home network or office network. Usually, this Ethernet
cable is plugged into a home NAT/router device or an Ethernet switch if in the office,
as shown in Figure 2-4. Since the default settings of the IP CAM use DHCP function
and very often there is a DHCP server on most of the Home/office network, the IP
CAM should be connected to the Internet immediately. The Internet status LED is
constant red light to indicate this good connection status. If the LED is blinking, please
refer to section 3.3~3.5 to try other network settings.