Yo-Yo Desk GO 2 User manual

We highly recommend Yo-YoDesk GO is assembled by two people together.
Please first read all instructions carefully before assembling. Retain this manual
for future reference. The specifications may vary slightly from the illustrations and
are subject to change without notice.
CAUTION
Assembly Manual
Yo-Yo DESK GO
®
The following items are included in your Yo-YoDesk GO, please check you have
each of them. If there are any tools or components missing, please contact customer
services on [phone].
ASSEMBLY KIT
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
Page 2 / 8
1 x
2 x
1 x
1 x
1 x
1 x Allen Keys
Allen Keys
Allen Keys
Screws M4x12
Screws
M5x12
Screws
M4x16
Screws
M5x16
Screws
Screws
Screws
Screw Collars
Screw Collars
Monitor Pole
1 x
1 x 4mm
3 x
1 x
4 x
4 x
AB
D
F
L S
T
U
V
W
X
Y
M
N
O
Q
R
P
G
H
I
J
K
4 x
4 x
1 x
4 x
1 x 5mm
1 x 6mm
D5
D8
E
C
Screwdriver
8 x
8 x
8 x
8 x
8 x
8 x
1 x
®
Yo-Yo DESK GO
ASSEMBLY STEP 1
CAUTION
WEIGHT TOLERANCE LEVEL1
WARNING
TWO PEOPLE REQUIRED
1)Align Base Plate with the Monitor Pole & then screw them together.
Please place the Yo-Yo DESK GO on a surface suitable to hold the entire base
of the Yo-Yo DESK GO otherwise you may cause damage when operating the
Yo-Yo DESK GO.
®
®
IP
A
C
We recommend a combined weight of
desk equipment ( ie laptop & monitor
screen of 12 kg ) for optimal counter-
balance. Below 5kg may make the
transition between sitting & standing
positions more stiff.
The Maximum weight tolerance is
12kg.
®
[phone]
[email protected]

U / V
ASSEMBLY STEP 2
When attaching the Monitor Arm, avoid excessive screwdriver force. Excessive
force may prevent or restrict the up/down movement of your monitor.
CAUTION
Page 3 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
2a
2b
2c
2) i Hold both LEFT and RIGHT sides of the Monitor Arms and carefully
screw together
Fit the Monitor Arm OVER
the Monitor Pole.
ii
Place the Top Cap on
top of the Monitor Pole.
iii
PJ
K
D
E
F
P
H
G N Y
®
[phone]
[email protected]
ASSEMBLY STEP 3
may drop down when pressure is applied.
CAUTION
Page 4 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
3a 3b
3a) Insert the Four Screws at the back of the Worktop. Screw them in partly,
avoid screwing in too tightly to allow some free movement.
Place Worktop over the bottom of the Monitor Pole, aligning the Four Screws
with the Monitor Pole, & then tighten carefully.
3b)
O
L
B
O
L
O
Do not press lever to avoid pole rising. Please tighten firmly. If not, Worktop
®
[phone]
[email protected]

M
®
ASSEMBLY STEP 4
Always test the Up/Down Lever by pressing inwards once it has been attached.
CAUTION
Page 5 / 8
4a
4) i Screw in the Up/Down Lever placing it underneath the RIGHT SIDE
of the Worktop.
[phone]
[email protected]
WW
X
U / V
S/T
Q
O
Q
ASSEMBLY STEP 5
Avoid excessive screwdriver force as this may restrict full swivel, tilt and rotation.
CAUTION
Page 6 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
5a
5c
5b
5a,b & c) Attach the monitor on to the Monitor Arm.
®
[phone]
[email protected]
®

Avoid pushing down from the front of the Worktop. Always place hand to the
back to maintain optimal stability when moving up/down.
CAUTION
Page 7 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
6
ASSEMBLY STEP 6
6) To operate, use right hand to push Up/Down Leverin & if necessary when
moving downwards apply pressure with your LEFT HAND to the back of the
Worktop. Apply pressure on the left corner pressing the lever simultaneously.
Sufficient weight on the Worktop should limit the necessity to do this. Pads can be
placed on the bottom of the base for better adherence to the surface.
®
[phone]
[email protected]
Please place the Yo-Yo Desk GO on a surface suitable to hold the entire base
of the Yo-Yo Desk GO otherwise you may cause damage when operating the
Yo-Yo Desk GO.
When attaching the Monitor Arm, avoid excessive screwdriver force.
Excessive force may prevent or restrict the up/down movement of your monitor.
Please tighten firmly. If not, Worktop may drop down when pressure is applied.
Always test the Up/Down Lever by pressing inwards once it has been attached.
Avoid excessive screwdriver force as this may restrict full swivel, tilt and rotation.
Avoid pushing down from the front of the Worktop. Always place hand to the
back to maintain optimal stability when moving up/down.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
Page 8 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
Yo-Yo DESK GO
Yo-Yo DESK GO
Yo-Yo DESK GO
®
[phone]
[email protected]