York STELLAR PLUS E*FH018 Quick start guide

036-21031-004 Rev. A (0603)
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
®
TECHNICAL GUIDE
STELLAR PLUS
TM
12 SEER
SPLIT-SYSTEM HEAT PUMPS
MODELS:
E*FH018 Thru E*FH060
(1.5 THRU 5 NOMINAL TONS)
Due to continuous product improvement, specifications
are subject to change without notice.
Visit us on the web at www.york.com for the most
up-to-date technical information.
Additional rating information can be found at
www.ariprimenet.org.
U
NI
T
A
R
Y
HE
A
T
P
U
M
P
T
E
Q
U
I
P
M
E
N
R
S
EC
T
I
O
N
S
A
T
I
O
N
E
RT
I
F
I
C
C
OF
D
ST
A
N
D
A
R
I
A
R
2
4
0
M
A
NU
F
A
CT
U
R
E
R
C
E
R
T
I
F
I
E
D
C
L
Y
OM
P
I
N
G
T
O
A
R
IA
S
LISTED
This product was manufactured
in a plant whose quality system
is certified/registered as being
in conformity with ISO 9001.
Certification applies only
when the complete
system is listed
with RI.
DESCRIPTION
These high efficiency EFH Series heat pump units are the out-
door part of a versatile system designed to economically heat
and cool a home or small business. The compact design of these
outdoor units make them ideal for ground or roof installation. The
units contain enough refrigerant charge for the outdoor unit, a
matched indoor coil and 15 feet of interconnecting piping.
EFH heat pumps can be custom-matched with one of YORK's
two lines of evaporator blower sections, each designed to serve
a specific function. Electric heaters are available for both, in a
variety of sizes.
For Add-On applications, the indoor coil may be applied in the
supply duct of a conventional gas, oil or electric furnace. The
heat pump will be the primary source of heat for the building with
the furnace operating only when the heating requirement
exceeds the capacity of the heat pump.
WARRANTY
5-year limited parts warranty.
10-year limited compressor warranty.
FEATURES
•QUALITY COILS - The coil is constructed of copper tube and alumi-
num fins.
•COIL PROTECTION - Coils are protected from damage by a polymer
mesh applied between the coil face, and a PVC coated steel coil
guard, or a polymer coil guard.
•DURABLE FINISH - Cabinet is made of pre-painted steel. The pre-
treated flat galvanized steel provides a better paint to steel bond,
which resists corrosion and rust creep. Special primer formulas and
glossy earth tone finish insure less fading when exposed to sunlight.
•LOWER INSTALLED COST - Installation time and costs are reduced
by the fully exposed refrigerant connections and the single panel cov-
ering of the electrical controls. The small base dimension means
smaller mounting pads or less materials required for mounting, lower-
ing installation costs.
•COMPRESSOR - 2 - 5 ton models are equipped with scroll compres-
sors which are internally protected against high pressure and tempera-
ture. This is accomplished by the simultaneous operation of high
pressure relief valve and a temperature sensor which protect the com-
pressor if undesirable operating conditions occur. The compressor is
protected by a 10 year limited warranty.
•COMPLETE SYSTEM CONTROL - These heat pump units utilize the
unique YorkGuard V microprocessor control system to provide optimal
comfort control and assure reliable operation. The YorkGuard V con-
trol system continuously monitors the space environment to maintain
optimum efficiency. It initiates defrost only when necessary to further
reduce heating costs and improve reliability. Supplemental heat can
only operate below the balance point and then only upon need. In the
event of improper operating conditions (high temperature and high
pressure), the YorkGuard V will shut the system down to extend the
life of the heat pump. Rapid cycling is prevented by use of an integral
anti-recycle timer. Loss of charge protection is provided by a discharge
temperature sensor and internal compressor overloads.
• Finally the YorkGuard V control provides system diagnostics to aid the
service technician, minimizing repair time and cost. The YorkGuard V
control even stores important information for use during servicing and
has a 5 year warranty.
•LOW OPERATING SOUND LEVEL - The discharge air from the top
mounted fan is blown up away from the structure and any landscaping
carrying the normal operating noise up away from the living area. The
rigid top panel effectively isolates any motor sound. Isolator mounted
compressor and the rippled fins of the condenser coil muffle the nor-
mal fan motor and compressor operating sounds.
•U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment certification pro-
gram, which is based on ARI Standard 210/240.

036-21031-004 Rev. A (0603)
2Unitary Products Group
All dimensions are in inches. They are subject to change
without notice. Certified dimensions will be provided upon
request.
PHYSICAL AND ELECTRICAL DATA
MODEL
E4FH018 E4FH024 E4FH030 E4FH036 E4FH045 E5FH048 E4FH060
Unit Supply Voltage 208/230-1-60
Normal Voltage Range
1
1. Rated in accordance with ARI Standard 110, utilization range “A”.
187 to 252
Minimum Circuit Ampacity 9.7 16.2 16.4 22.1 25.4 33.3 37.8
Max. Overcurrent Device Amps
2
2. Dual element fuses or HACR circuit breaker.
15 25 25 35 35 50 50
Compressor Type
3
3. All scrolls listed with a superscript “B” are Bristol scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.
Recip Scroll
C
Scroll
C
Scroll
C
Scroll
C
Scroll
C
Scroll
C
Compressor Amps Rated Load 6.7 10.3 12.2 16.4 19 21.4 28.8
CrankcaseHeater YesNoNoNoNoNoNo
Fan Motor Amps Rated Load 0.8 0.8 0.9 1.6 1.6 1.6 1.8
Fan Diameter Inches 18 18 18 24 24 24 24
Fan Motor Rated HP 1/12 1/12 1/8 1/4 1/4 1/4 1/3 Nominal RPM 1050 1050 1075 850 850 850 1075
Nominal CFM 1500 1500 2050 3300 3400 3400 4100
Coil Face Area Sq. Ft. 14.1 14.1 14.1 20.0 24 24 24 RowsDeep 1111112
Fin / Inches 16 16 20 16 16 16 13
Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line OD 5/8 5/8 3/4 7/8 7/8 7/8 1 - 1/8
Unit Charge (Lbs. - Oz.)
4
4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or sub-
tract the amount of refrigerant, using the difference in length multiplied by the per foot value.
5 - 9 5 - 1 5 - 9 6 - 14 8 - 3 9 - 11 14 - 0
Charge Per Foot, Oz. 0.68 0.68 0.68 0 .68 0 .70 0.70 0.70
Operating Weight Lbs. 156 148 150 212 237 272 300
48" OVERHEAD
CLEARANCE
C
B
A
5-1/2
2-3/8
3-1/8
VAPOR
CONNECTION
LIQUID CONNECTION
AIR IN
4 SIDES
UNIT MODEL
EFH DIMENSIONS REFRIGERANT
CONNECTION
LINE SIZE
ABCLIQUIDVAPOR
018 30-1/8 24 24
3/8
5/8
024 30-1/8 24 24
030 30-1/8 24 24 3/4
036 30-7/8 35 35 7/8042 37-7/8 35 35
048 37-7/8 35 35
060 37-7/8 35 35 1-1/8
1
1. Valve on 060 is 7/8 with a reducer supplied for the 1-1/8
vapor line.

036-21031-004 Rev. A (0603)
Unitary Products Group 3
PROCEDURES:
1. Unit factory charge listed on the unit nameplate includes refigerant for the condenser, the smallest evaporator and for 15 feet of intercon-
necting line tubing.
2. Verify the orifice size and the additional charge required for the specific evaporator coil in the system using the table above:
3. Add additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.
4. Permanently mark the unit nameplate with the total system charge. Total System Charge=Base Charge (as shipped) +adder for
evaporator +adder for line set.
5. If the orifice in the evaporator was changed verify the evaporator nameplate has been marked with the correct orifice size.
ADDITIONAL R-22 CHARGE / ORIFICE SIZE FOR VARIOUS MATCHED SYSTEMS
OUTDOOR UNIT E4FH018 E4FH024 E4FH030 E4FH036 E4FH042 E5FH048 E4FH060
Orifice in OD Distributor 37 45 49 55 65 69 76
FACTORY CHARGE, LBS. - OZ. 5 - 9 5 - 1 5 - 12 6 - 14 8 - 3 9-11 14 - 0
ID Orifice included w/Instruction Package 57 59 -- -- -- -- --
INDOOR COIL COIL ORIFICE
1
1. Verify the TXV kit and the additional charge required for the specific evaporator coil in the system using the table above.
REQUIRED SYSTEM ORIFICE + ADDITIONAL CHARGE, OZ.
G1FA/G1UA024S14, 17 59 57 + 4 -- -- -- -- -- --
G1FA/G1UA030S14 65 57 + 6 701 + 0 701
1
+ 0 -- -- -- --
G1FA/G1UA036S14 73 -- 701 + 2 701
1
+ 0 -- -- -- --
G1FA/G1UA036S17 73 -- -- 701
1
+ 0 -- -- -- --
G1FA/G1UA048S17 84 -- -- -- -- -- -- --
G1FA/G1UA048S21 84 -- -- -- 702
1
+ 0 702
1
+ 0 703
1
+ 0 --
G1FA/G1UA060S21, 24 90 -- -- -- 702
1
+ 2 702
1
+ 5 703
1
+ 5 703
1
+ 0
G2FD024S(H)14, 17 61 57 + 6 59 + 0 -- -- -- -- --
G2FD030S(H)17 65 701
1
+ 8 59 + 2 701
1
+ 0 -- -- -- --
GFD035S(H)14 65 -- 59 + 2 701
1
+ 0 -- -- -- --
G2FD036S(H)17 75 -- -- 701
1
+ 4 702
1
+ 0 -- -- --
G2FD042S(H)21 78 -- -- -- 702
1
+ 2 702
1
+ 0 -- --
G2FD046S(H)17 78 -- -- -- 702
1
+ 2 702
1
+ 0 -- --
G2FD048S(H)21, 24 84 -- -- -- -- 702
1
+ 8 703
1
+ 4 --
G2FD060S(H)24 90 -- -- -- -- -- 703
1
+ 5 703
1
+ 0
G2FD061SH24 90 -- -- -- -- -- -- 703
1
+ 8
G1HD024 59 -- 59 + 1 -- -- -- -- --
G1HD036 69 -- -- 701
1
+ 4 -- -- -- --
G1HD048 81 -- -- -- -- -- -- --
G1HD060 93 -- -- -- -- -- -- --
F2RP/FP018 (53) (55) +0 -- -- -- -- -- --
F2RP/FP024 61 57 + 6 59 + 0 -- -- -- -- --
F2RP/FP030 65 -- 59 + 2 701
1
+ 0 -- -- -- --
F2RP/FP036 75 -- -- 701
1
+ 4 702
1
+ 0 -- -- --
F2RP/FP042 78 -- -- -- 702
1
+ 2 702
1
+ 0 -- --
F2FP048 84 -- -- -- -- 702
1
+ 8 703
1
+ 3 --
F2FP060 90 -- -- -- -- -- 703
1
+ 5 703
1
+ 0
F2FV060 90 -- -- -- -- -- 703
1
+ 5 703
1
+ 0
FOOTNOTES:

036-21031-004 Rev. A (0603)
4Unitary Products Group
- = Not applicable
COOLING CAPACITY - With Air Handler Coils
UNIT
MODEL
AIR HANDLER
COIL MODEL
1
1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.
COOLING
MODEL ELECTRIC
HEAT KW
2
2. Single phase units require single phase 2HK heaters.
WRATED
CFM NET MBH SEER
W/O TXV SEER + TXV
3
3. TXV = Use 1TV700 Series Kit.
EER
TOTAL SENS.
1 Phase 12 SEER HP / N1AH / G2FD
E4FH018 N1AHB08 2,5,7.5,10 17 G2FD024(S,H)17 650 19.0 14.3 12.05 --- 10.65
N1AHB08 2,5,7.5,10 17 G2FD030(S,H)17 650 19.4 14.6 12.15 --- 10.70
E4FH024 N1AHB08 2,5,7.5,10 17 G2FD024(S,H)17 800 23.4 17.6 12.10 --- 10.85 N1AHB08 2,5,7.5,10 17 G2FD030(S,H)17 850 23.4 17.6 12.10 --- 10.85
N1AHB08 2,5,7.5,10 14 G2FD035(S,H)14 850 23.4 17.6 12.10 --- 10.85
E4FH030 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1000 29.0 21.8 --- 12.40 10.65
E4FH036 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1200 34.6 25.6 -- 12.00 10.50
E4FH042 N1AHC16 5,7.5,10,15,20 21 G2FD042(S,H)21 1400 40.0 29.6 -- 12.00 10.50
N1AHC16 5,7.5,10,15,20 21 G2FD048(S,H)21 1425 41.0 30.3 -- 12.40 10.80
E5FH048 N1AHC16 5.7.5,10,15,20 21 G2FD048(S,H)21 1600 47.5 35.6 -- 12.00 10.50
N1AHD20 5.7.5,10,15,20,25,30 24 G2FD060(S,H)24 1620 48.0 36.0 -- 12.40 10.85
E4FH060 N1AHD20 7.5,10,15,20,25,30 24 G2FD060(S,H)24 1850 58.0 42.0 -- 12.00 10.70
N1AHD20 7.5,10,15,20,25,30 24 G2FD061H24 1875 58.5 41.5 -- 12.20 10.70
1 Phase 12 SEER HP / N1VS / G2FD
E4FH018 N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H)17 650 19.4 14.3 13.35 --- 11.70
E4FH024 N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H)17 800 24.0 18.0 14.00 --- 12.00
E4FH030 N1VSB12 5,7.5,10,15,18 17 G2FD030(S,H)17 1000 29.0 21.8 --- 13.00 11.20
N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1000 29.2 21.9 --- 13.50 11.40
E4FH036 N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H)17 1200 35.0 25.9 -- 12.80 11.20
E4FH042 N1VSC16 5,7.5,10,15,20 21 G2FD042(S,H)21 1400 40.5 30.0 -- 12.80 11.20
N1VSC16 5,7.5,10,15,20 21 G2FD048(S,H)21 1425 41.5 30.7 -- 13.50 11.40
E5FH048 N1VSC16 5.7.5,10,15,20 21 G2FD048(S,H)21 1600 48.0 36.0 --- 13.40 10.50
N1VSD20 5.7.5,10,15,20,25,30 24 G2FD060(S,H)24 1650 49.0 36.8 --- 13.80 10.80
E4FH060 N1VSD20 7.5,10,15,20,25,30 24 G2FD060(S,H)24 1850 60.5 42.9 -- 13.00 11.60
N1VSD20 7.5,10,15,20,25,30 24 G2FD061H24 1875 59.0 41.5 -- 12.60 11.90
1 Phase 12 SEER HP / F2RP / FP / FV
4,5
4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC . models. All ratings remain the same.
5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard.
E4FH018 F2RP/F2FP018 5,8,10 18 -- 650 18.0 13.5 12.00 --- 10.75
F2RP/F2FP024 5,8,10 18 -- 650 19.0 14.3 12.50 --- 10.50
E4FH024 F2RP/F2FP024 5,8,10 18 -- 800 23.4 17.6 12.00 --- 10.35
F2RP/F2FP030 5,8,10,15 18 -- 800 23.8 17.9 --- 12.50 10.55
E4FH030 F2RP/F2FP030 5,8,10,15 18 --- 1035 28.2 21.2 --- 12.00 10.30
F2RP/F2FP036 5,8,10,15 21 --- 1035 29.0 21.8 --- 12.00 10.30
E4FH036 F2RP036 5,8,10,15 18 -- 1250 34.6 25.6 -- 12.10 10.60
F2RP042 5,8,10,15 21 -- 1250 34.6 25.6 -- 12.10 10.50
E4FH042 F2RP042 5,8,10,15 21 -- 1400 40.0 29.6 -- 12.00 10.40
F2FP048 10,15,20,25 24 -- 1600 41.0 30.3 -- 12.40 10.80
E5FH048 F2FP048 10,15,20,25 24 -- 1600 47.0 35.3 --- 12.00 10.45 F2V060 10,15,20,25 24 -- 1600 48.5 36.4 --- 13.00 11.60
F2FP060 10,15,20,25 24 -- 1600 47.5 35.6 --- 12.00 10.35
E4FH060 F2FP060 10,15,20,25 24 -- 1850 57.0 42.2 -- 11.60 10.40
F2FV060H24 10,15,20,25 24 -- 1875 59.0 43.0 -- 13.00 11.60
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210/240.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the totalcooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input
in watt-hours during the same period.

036-21031-004 Rev. A (0603)
Unitary Products Group 5
* Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one.
** Refer to Quick Selection Chart for specific furnace match-up.
COOLING CAPACITY - With Upflow, Downflow and Horizontal Furnace and Coils
UNIT
MODEL
FURNACE** COIL
MODEL
COOLING
NOMINAL
AIRFLOW WRATED CFM NET MBH SEER W/O TXV SEER + TXV
1
1. TXV = Use 1TV700 Series Kit.
EER
TOTAL SENS.
E4FH018S06 575
725
14,17 G1FA024S14,17 650 18.8 14.1 12.00 - 10.55
14 G1FA030S14 650 19.0 14.3 12.50 - 10.65
14,17 G1UA024S14,17 650 18.8 14.1 12.00 - 10.55
14 G1UA030S14 650 19.0 14.3 12.50 - 10.65
14,17 G2FD024S14,17 650 19.0 14.3 12.50 - 10.65
17 G2FD030(S,H)17 650 19.2 14.4 12.50 - 10.70
14 G2FD035(S,H)14 650 19.2 14.4 12.50 - 10.70
E4FH024S06 725
925
14 G1FA030S14 800 22.2 16.7 - 12.00 10.85
G1UA030S14 800 22.2 16.7 - 12.00 10.85
17,21 G1FA036S17,21 800 22.4 16.8 - 12.10 11.00
G1UA036S17,21 800 22.4 16.8 - 12.10 11.00
- G1HD024 820 23.6 17.7 12.10 - 10.85
17 G2FD024(S,H)14,17 820 23.6 17.7 12.10 - 10.85
17 G2FD030(S,H)17 820 23.6 17.7 12.10 - 11.00
14 G2FD035(S,H)14 820 23.6 17.7 12.10 - 11.00
E4FH030S06 925
1175
14 G1FA036S14 1050 28.2 21.2 - 12.00 10.35
17,21 G1FA036S17,21 1050 28.2 21.2 - 12.00 10.35
- G1HD036 1035 28.8 21.6 - 12.00 10.30
14 G1UA036S14 1050 28.2 21.2 - 12.00 10.35
17,21 G1UA036S17,21 1050 28.2 21.2 - 12.00 10.35
17 G2FD030(S,H)17 1050 28.2 21.2 - 12.00 10.35
17 G2FD030(S,H)17 1050 28.2 21.2 - 12.00 10.35
14 G2FD035(S,H)14 1050 28.6 21.5 - 12.00 10.35
17 G2FD036(S,H)17 1050 28.8 21.6 - 12.00 10.65
21 G2FD036(S,H)21 1050 28.8 21.6 - 12.00 10.65
E4FH036S06 1075
1375
17 G1FA048S17 1225 35.0 25.9 - 12.10 10.60
21 G1FA048S21 1225 35.4 26.2 - 12.50 10.70
17 G1UA048S17 1225 35.0 25.9 - 12.10 10.60
21 G1UA048S21 1225 35.4 26.2 - 12.50 10.70
17 G2FD036(S,H)17 1200 34.6 26.2 - 12.00 10.50
21 G2FD036(S,H)21 1200 34.6 26.2 - 12.00 10.50
21 G2FD042(S,H)21 1225 34.8 25.8 - 12.20 10.55
17 G2FD046(S,H)17 1225 35.0 25.9 - 12.10 10.60
E4FH042S06 1275
1625
17 G1FA048S17 1450 40.5 30.0 - 12.25 10.65
21 G1FA048S21 1450 40.5 30.0 - 12.40 10.70
17 G1UA048S17 1450 40.5 30.0 - 12.25 10.65
21 G1UA048S21 1450 40.5 30.0 - 12.40 10.70
21 G2FD042(S,H)21 1450 40.0 29.6 - 12.00 10.50
17 G2FD046(S,H)17 1450 40.5 30.0 - 12.25 10.65
21,24 G2FD048(S,H)21,24 1450 41.0 30.3 - 12.40 10.80
E5FH048S06 1400
1800
21 G1FA048S21 1600 46.5 34.9 - 12.00 10.45
21,24 G1FA060S21,24 1650 47.5 35.6 - 12.20 10.60
21 G1UA048S21 1600 46.5 34.9 - 12.00 10.45
21,24 G1UA060S21,24 1650 47.5 35.6 - 12.20 10.60
21,24 G2FD048(S,H)21,24 1600 47.5 35.6 - 12.00 10.50
24 G2FD060(S,H)24 1625 48.0 36.0 - 12.50 10.80
E4FH060S06 1600
2100
21,24 G1FA060S21,24 1850 57.0 41.0 - 11.70 10.40
21,24 G1UA060S21,24 1850 57.0 41.0 - 11.70 10.40
24 G2FD060(S,H)24 1800 58.0 42.0 - 12.00 10.70
24 G2FD061H24 1800 58.5 41.5 - 12.20 10.70

036-21031-004 Rev. A (0603)
6Unitary Products Group
HEATING PERFORMANCE - Air Handler and Multi-position Coils
UNIT
MODEL COIL
1
MODEL
ARI HEATING
2
OUTDOOR TEMP
3
47 °F 17 °FHSPF-3°F7°F17°F 27°F 37°F 47°F57°F
MBH COP MBH COP STD. V. S. MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW
E4FH018
F2RP/F2FP018 17 3.00 10 2.00 6.8 -- 4 1.3 7.8 1.27 10 1.35 12.3 1.60 15.2 1.6 17 1.61 17.6 1.66
F2RP/F2FP024 19.5 3.20 11.3 2.10 7.5 -- 4.5 1.25 8 1.25 11.3 1.36 12.7 1.57 15.5 1.68 19.5 1.59 19.6 1.65
G2FD024(S,H)14,17 19.0 3.32 11.6 2.00 7.6 8 6 1.51 8 1.25 11.6 1.36 12.9 1.40 16.5 1.52 19.8 1.59 19.6 1.65
G2FD030(S,H)17 19.8 3.40 1.16 2.24 7.5 -- 6.2 1.52 8.2 1.23 11.6 1.69 12.8 1.38 16.4 1.5 19.8 1.79 19.6 1.63
G2FD035(S,H)14 19.8 3.40 1.16 2.24 7.5 -- 6.2 1.5 8.2 1.25 11.6 1.69 12.9 1.39 16.6 1.51 19.8 1.79 19.8 1.64
E4FH024
F2RP/F2FP024 24 3.32 12.9 2.20 8 -- 6.6 1.55 11 1.78 12.9 1.7 16 1.85 18.8 1.87 24 1.8 26.6 2.07
F2RP/F2FP030 24 3.32 12.9 2.20 8 -- 6.8 1.56 11.4 1.76 12.9 1.78 16.2 1.84 19 1.85 24 2.07 26.8 2.08
G2FD024(S,H)14,17 23.8 3.40 13.5 2.30 8 8.1 6.6 1.58 11.6 1.75 13.5 1.78 16.3 1.82 19.1 1.85 23.8 2.07 26.6 2.1
G2FD030(S,H)17 24 3.26 13.6 2.18 8 -- 6.8 1.6 11.4 1.73 13.6 1.75 16.2 1.80 19.2 1.83 24 2.08 26.8 2.08
G2FD035(S,H)14 24 3.26 13.6 2.18 8 -- 6.9 1.57 11.6 1.74 13.6 1.77 16.4 1.80 19.4 1.8 24 2.06 26.8 2.1
E4FH030
F2RP/F2FP030 28 3.33 17 2.33 8 -- 9.6 1.98 13.1 2.1 16.6 2.21 20.3 2.33 24.3 2.46 28 2.56 32.9 2.7
F2RP/F2FP036 28 3.33 17 2.33 8 -- 9.6 1.95 13.1 2.09 16.7 2.21 20.2 2.34 24.4 2.48 28 2.57 33 2.71
G2FD030(S,H)17 28 3.33 17 2.33 8 8.2 9.8 2.06 13.1 2.14 16.5 2.2 19.9 2.29 23.9 2.4 28 2.5 32.7 2.55
G2FD035(S,H)14 28 3.33 17 2.33 8 -- 9.4 2.06 13.2 2.14 16.6 2.3 20 2.31 24 2.41 28 2.6 33 2.6
G2FD036(S,H)17,21 28 3.33 17 2.33 8 8.2 9.9 2.02 13.3 2.15 16.6 2.19 21 2.41 23.8 2.4 28 2.6 33.4 2.65
E4FH036
F2RP/F2FP036 36.0 3.10 21.8 2.30 8.0 -- 12.5 2.36 17.1 2.57 21.8 2.78 26.5 2.99 31.7 3.21 36.0 3.40 41.4 3.56
F2RP/F2FP042 36.0 3.10 21.8 2.30 8.0 -- 12.5 2.35 17.2 2.57 21.8 2.78 26.4 2.99 31.6 3.21 36.0 3.40 41.5 3.57
G2FD042(S,H)21 36.0 3.38 21.8 2.26 8.0 -- 12.5 2.63 17.1 2.73 21.8 2.83 26.5 2.93 31.7 3.04 36.0 3.12 41.7 3.18
G2FD046(S,H)17 36.0 3.38 21.8 2.26 8.0 -- 12.5 2.63 17.2 2.73 21.8 2.83 26.4 2.93 31.7 3.04 36.0 3.12 41.4 3.16
G2FD036(S,H)17,21 36.0 3.40 21.8 2.28 8.0 8.1 12.5 2.60 17.1 2.70 21.8 2.80 26.5 2.90 31.7 3.02 36.0 3.10 41.7 3.16
E4FH042
F2RP/F2FP042 42.0 3.30 25.2 2.20 7.8 -- 13.4 3.08 19.3 3.22 25.2 3.36 31.1 3.50 37.7 3.63 42.0 3.73 48.5 3.85
F2FP048 42.0 3.58 25.2 2.32 8.0 -- 12.5 2.98 18.8 3.08 25.2 3.18 31.6 3.29 38.6 3.40 42.0 3.44 50.4 3.56
G2FD042(S,H)21 41.5 3.40 25.0 2.26 8.0 8.1 12.5 2.94 18.8 3.09 25.0 3.24 31.2 3.39 38.2 3.55 41.5 3.58 49.6 3.73
G2FD046(S,H)17 41.5 3.40 25.0 2.24 8.0 -- 13.4 3.05 19.2 3.16 25.0 3.27 30.8 3.38 37.3 3.51 41.5 3.58 47.8 3.66
G2FD048(S,H)21,24 42.0 3.58 25.2 2.32 8.0 8.0 12.4 2.98 18.8 3.08 25.2 3.18 31.6 3.29 38.7 3.41 42.0 3.44 50.4 3.56
E5FH048
F2FP048 47.5 3.30 28.4 2.20 8.1 -- 17 3.54 22.6 3.66 28.4 3.78 34.2 3.91 39 3.76 47.5 4.03 53.5 4.13
F2FP060 47.5 3.30 28 2.20 8.1 -- 18 3.5 22.8 3.58 28 3.75 34.6 3.95 40 3.8 47.5 4.15 54 4.3
G2FD048(S,H)21,24 48 3.48 28 2.34 8.1 8.2 17 3.52 22.6 3.6 28 3.76 34.2 3.96 40 3.9 48 4.04 53.5 4.25
G2FD060(S,H)24 48.5 3.30 28.4 2.20 8.1 8.2 18 3.55 22.8 3.65 28.4 3.78 34.6 3.96 40 3.8 48.5 4.03 54 4.26
E4FH060
F2FP060 60.0 3.40 40.0 2.40 8.0 -- 18.7 4.08 26.1 4.44 40.0 4.80 40.7 5.16 49.0 5.55 60.0 5.94 68.6 6.25
F2FV060 60.0 3.00 40.0 2.60 -- 8.3 17.6 3.93 24.6 4.11 40.0 4.29 38.6 4.47 46.6 4.68 60.0 4.93 66.1 5.07
G2FD060(S,H)24 60.0 3.50 40.0 2.50 8.2 8.3 18.9 3.94 26.0 4.21 40.0 4.48 40.0 4.75 48.1 5.05 60.0 5.39 67.8 5.61
G2FD061H24 62.0 3.60 41.0 2.60 8.4 – 20.2 4.07 26.9 4.28 41.0 4.49 40.5 4.70 48.3 4.95 62.0 5.22 67.5 5.39
For Notes See Page 7.

036-21031-004 Rev. A (0603)
Unitary Products Group 7
COP equals MBH output divided by (total KW input x 3.412).
HSPF (Heating Seasonal Performance Factor) is the total heating output during a normal annual usage period for heating divided by the total electric
power input during the same period.
— = Not Applicable.
HEATING PERFORMANCE - Furnace Coils
UNIT
MODEL COIL
1
MODEL
1. Rated CFM same as for cooling.
ARI HEATING
2
2. Heating MBH based on ARI standards of 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental
electric heat operation.
OUTDOOR TEMP
3
3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur.
47°F 17 °F HSPF -3 °F7°F17°F 27°F37°F 47°F 57°F
MBH COP MBH COP STD. V. S. MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW
E*FH WITH (VARIABLE SPEED & STANDARD) FURNACE COILS
E4FH018
G1HD024 18 3.08 9.9 2.00 7.1 -- 6.2 1.1 9 1.15 9.9 1.25 13.6 1.4 16 1.5 18 1.6 20 1.75
G1FA024S17 19.0 3.24 11.4 2.16 7.6 -- 6.6 1.09 9.2 1.1 11.4 1.25 13.8 1.45 16.6 1.54 19.6 1.64 22 1.74
G1UA024S17 19.0 3.24 11.4 2.16 7.6 -- 6.6 1.09 9.2 1.1 11.4 1.25 13.8 1.45 16.6 1.54 19.6 1.64 22 1.74
G1FA030S14 19.0 3.32 11.6 2.20 7.6 -- 6.6 1.08 9.2 1.15 11.6 1.27 14.2 1.43 16.8 1.5 19.8 1.62 22.4 1.76
G1UA030S14 19.0 3.32 11.6 2.20 7.6 -- 6.6 1.08 9.2 1.15 11.6 1.27 14.2 1.43 16.8 1.5 19.8 1.62 22.4 1.76
E4FH024
G1HD024 24 3.16 12.2 2.00 8 -- 7.2 1.57 10 1.67 12.2 1.76 16.4 1.9 19.6 1.95 24 2.05 27.4 2.17
G1FA030S17 23.6 3.16 13.4 2.14 8 -- 7.6 1.5 10.4 1.65 13.4 1.76 16.6 1.85 19.8 1.97 23.6 2.03 27.6 2.16
G1UA030S17 23.6 3.16 13.4 2.14 8 -- 7.6 1.5 10.4 1.65 13.4 1.76 16.6 1.85 19.8 1.97 23.6 2.03 27.6 2.16
G1FA036S17,21 24 3.26 13.6 2.18 8 -- 7.6 1.52 10.4 1.6 13.6 1.76 16.8 1.9 20 1.9 24 2.03 28.2 2.18
G1UA036S17,21 24 3.26 13.6 2.18 8 -- 7.6 1.52 10.4 1.6 13.6 1.76 16.8 1.9 20 1.9 24 2.03 28.2 2.18
E4FH030
G1HD036 28 3.33 17 2.3 8 -- 9.8 2.08 13.1 2.14 16.6 2.1 19.8 2.2 23.8 2.38 28 2.5 39.8 2.55
G1FA036S14 28 3.33 17.2 2.3 8 -- 10 2.07 13.2 2.15 16.8 2.3 19.9 2.3 23.9 2.39 28 2.5 34 2.57
G1UA036S14 28 3.33 17.2 2.3 8 -- 10 2.07 13.2 2.15 16.8 2.3 19.9 2.3 23.9 2.39 28 2.5 34 2.57
G1FA036S17,21 28 3.33 17.2 2.3 8 -- 10.1 2.08 13.3 2.17 17 2.4 20.1 2.4 24.1 2.4 28 2.55 34.2 2.6
G1UA036S17,21 28 3.33 17.2 2.3 8 -- 10.1 2.08 13.3 2.17 17 2.4 20.1 2.4 24.1 2.4 28 2.55 34.2 2.6
E4FH036
G1FA048S21 35.6 3.46 21.8 2.30 8.0 -- 12.8 2.61 17.3 2.69 21.8 2.78 26.3 2.86 31.3 2.95 35.6 3.02 41.2 3.07
G1UA048S21 35.6 3.46 21.8 2.30 8.0 -- 12.8 2.61 17.3 2.69 21.8 2.78 26.3 2.86 31.3 2.95 35.6 3.02 41.2 3.07
G1FA048S17 36.0 3.38 21.8 2.26 8.0 -- 12.5 2.63 17.2 2.73 21.8 2.83 26.4 2.93 31.7 3.04 36.0 3.12 41.4 3.16
G1UA048S17 36.0 3.38 21.8 2.26 8.0 -- 12.5 2.63 17.2 2.73 21.8 2.83 26.4 2.93 31.7 3.04 36.0 3.12 41.4 3.16
E4FH042
G1FA048S21 42.0 3.50 25.2 2.30 8.0 -- 12.5 2.98 18.9 3.09 25.2 3.21 31.5 3.33 38.5 3.47 42.0 3.52 50.3 3.66
G1UA048S21 42.0 3.50 25.2 2.30 8.0 -- 12.5 2.98 18.9 3.09 25.2 3.21 31.5 3.33 38.5 3.47 42.0 3.52 50.3 3.66
G1FA048S17 41.5 3.40 25.0 2.24 8.0 -- 13.4 3.05 19.2 3.16 25.0 3.27 30.8 3.38 37.3 3.51 41.5 3.58 47.8 3.66
G1UA048S17 41.5 3.40 25.0 2.24 8.0 -- 13.4 3.05 19.2 3.16 25.0 3.27 30.8 3.38 37.3 3.51 41.5 3.58 47.8 3.66
E5FH048
G1FA048S21 48 3.40 28 2.30 8 -- 16.1 3.23 22.1 3.41 28 3.57 34 3.72 40.6 3.91 48 4.06 54.8 4.16
G1UA048S21 48 3.40 28 2.30 8 -- 16.1 3.23 22.1 3.41 28 3.57 34 3.72 40.6 3.91 48 4.06 54.8 4.16
G1FA060S21,24 48 3.40 28 2.30 8 -- 16.2 3.24 22.2 3.42 28 3.55 34 3.7 40.6 3.92 48 4 54.9 4.18
G1UA060S21,24 48 3.40 28 2.30 8 -- 16.2 3.24 22.2 3.42 28 3.55 34 3.7 40.6 3.92 48 4 54.9 4.18
E4FH060 G1FA060S21,24 60.0 3.40 40.0 2.40 8.0 -- 18.9 3.95 26.0 4.21 33.0 4.48 40.1 4.74 48.1 5.04 57.0 5.39 67.8 5.60
G1UA060S21,24 60.0 3.40 40.0 2.40 8.0 -- 18.9 3.95 26.0 4.21 33.0 4.48 40.1 4.74 48.1 5.04 57.0 5.39 67.8 5.60

036-21031-004 Rev. A (0603)
8Unitary Products Group
ACCESSORIES
Refer to Price Manual for specific model numbers.
Start Assist Kit (2SA067*)
Blower Time Delay - Available to increase efficiency when
installed. Installs on indoor section and maintains blower for
approximately one minute after cooling thermostat has been
satisfied.
Hard Start Kits - Provides required starting torque for use
with Thermal Expansion Valve Kit.
Low Temperature Cutout (2LT06700224) - Prevents heat
pump operation below -10°F ambient temperature.
Compressor Blanket - Designed to further reduce the nor-
mal operating sound.
Add-on Control (2AC02700701) - Provides interface for use
of gas and oil furnaces with the heat pump system.
Thermal Expansion Valve Kit - 1TV0700 Series TXV kit
used to improve system performance.
Outdoor Thermostat (2TD06700124) - Provides additional
staging of supplemental electric heat.
Room Thermostats - A wide selection of matching thermo-
stats is available to provide features required for any installa-
tion.
2H/1C, manual change-over electronic non-programmable
thermostat.
3H/2C, non-programmable digital thermostat.
3H/2C, auto/manual changeover, electronic programmable,
7-day, thermostat.
* For the most current accessory information, refer to the
price book or consult factroy.
SOUND BLANKET
*Rated in accordance with ARI Standard 270.
EFH
MODEL SOUND RATING DECIBELS
018 72
024 73
030 74
036 74
042 74
048 76
060 76

036-21031-004 Rev. A (0603)
Unitary Products Group 9
TYPICAL INSTALLATION
TYPICAL FIELD WIRING - (AIR HANDLER / ELECTRICAL HEAT)
THERMOSTAT
TO
INDOOR
BLOWER
TO COIL
NEC
CLASS 2
WIRING
NEC
CLASS 1
WIRING
TO
POWER
SUPPLY
WEATHERPROOF
DISCONNECT
SWITCH
Seal opening( ) with permagum
or equivalent
24” SERVICE ACCESS
CLEARANCE
48” OVERHEAD
CLEARANCE
12” REAR AND
SIDES
NOTE: All outdoor wiring mu t be weatherproof
THERMOSTAT
O
R
Y
W
G
O
R
C
Y
G
S1*
S2*
O
R
Y
LL WIRING TO BE CCORD NCE WITH N TION L CODE ND/OR LOC L CODES.
INDOOR UNIT
ELECTRIC HEATER ACCESSORY
3
XorL
BorC
2
TERMIN L NOT USED ON LL THERMOST TS.
OUTDOOR
UNIT
POWER WIRING
24V CONTROL WIRING (NEC CL SS 2)
POWER WIRING
208/230-1-60
CONT CTOR
GND.
SCREW
GND.
LUG
CIRCUIT
BRE KER4
3
FOR TYPIC L FIELD WIRING WITH N*VS V RI BLE
SPEED IR H NDLER, SEE N*VS INSTRUCTIONS.
4
CONNECT POWER WIRING TO TERMIN L BLOCK
ON UNITS WITHOUT ELECTRIC HE T OR UNITS
WITHOUT CIRCUIT BRE KER.
T2 T1
L2 L1
M
W2
W1
W
W2/60
W1/66
BorC
XorL
BONNET SENSOR
CONNECTIONS FOR
DD-ON SYSTEM.
*
POWER WIRING
208/230-1-60

036-21031-004 Rev. A (0603)
10 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH018S06
INDOOR COIL MODEL NO. F2RP/F2FP024
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 600 650 700
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 24.0 22.0 20.1 18.2 24.3 22.3 20.3 18.5 24.5 22.6 20.6 18.7 S.C. 14.8 14.9 15.0 15.1 15.4 15.5 15.6 15.7 15.9 16.0 16.2 16.2
K.W 1.57 1.61 1.63 1.62 1.59 1.64 1.66 1.66 1.60 1.64 1.67 1.67
85 T.C. 22.9 21.0 19.0 17.2 23.2 21.3 19.3 17.6 23.4 21.5 19.5 17.9 S.C. 14.5 14.5 14.7 14.7 15.1 15.1 15.3 15.5 15.7 15.7 15.8 16.0
K.W 1.65 1.68 1.68 1.67 1.68 1.70 1.71 1.70 1.68 1.71 1.72 1.71
95 T.C. 20.7 18.8 17.0 15.5 20.9 19.0 17.2 15.7 21.0 19.2 17.5 15.9 S.C. 13.8 13.8 13.9 13.9 14.4 14.3 14.4 14.5 14.9 14.9 15.1 15.0
K.W 1.78 1.79 1.79 1.77 1.80 1.82 1.82 1.81 1.81 1.83 1.83 1.82
105 T.C. 18.6 16.8 15.3 13.8 18.7 17.0 15.5 14.1 18.9 17.3 15.6 14.4 S.C. 13.2 13.0 13.2 13.1 13.7 13.6 13.8 13.8 14.3 14.4 14.3 13.8
K.W 1.94 1.94 1.93 1.90 1.96 1.97 1.96 1.94 1.97 1.98 1.97 0.52
115 T.C. 16.4 15.0 13.5 12.3 16.6 15.1 13.6 12.6 16.8 15.3 13.9 12.8 S.C. 12.4 12.5 12.5 12.0 13.1 13.0 13.0 12.3 13.8 13.6 13.6 12.5
K.W 2.13 2.12 2.09 2.06 2.16 2.15 2.12 2.10 2.17 2.16 2.14 2.11
125 T.C. 14.3 13.1 11.8 10.7 14.5 13.2 11.8 11.1 14.7 13.4 12.1 11.3 S.C. 11.7 11.9 11.8 11.1 12.5 12.4 12.3 11.2 13.3 13.0 12.9 11.3
K.W 2.31 2.29 2.24 2.21 2.34 2.32 2.27 2.25 2.35 2.33 2.30 2.26
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHB08 G2FD024(S,H)17 1.00 1.00 0.94
N1AHB08 G2FD030(S,H)17 1.02 1.02 1.00
N1VSB12 G2FD024(S,H)17 1.02 1.00 0.94
F2RP/F2FP018 0.95 0.94 0.94
G1UA024S14 0.99 0.99 1.00
G1UA024S17 0.99 0.99 1.00
G2FD024(S,H)14 1.00 1.00 1.00
G2FD024(S,H)17 1.00 1.00 1.00
G1UA030S14 1.00 1.00 1.00
G2FD030(S,H)14 1.02 1.02 1.00
G2FD030(S,H)17 1.02 1.02 1.00
G1FA024S14 0.99 0.99 1.00
G1FA024S17 0.99 0.99 1.00
G1FA030S14 1.00 1.00 1.00

036-21031-004 Rev. A (0603)
Unitary Products Group 11
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH024S06
INDOOR COIL MODEL NO. F2RP/F2FP030
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 750 800 850
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 28.2 26.0 23.8 21.9 28.4 26.2 24.1 22.0 28.6 26.4 24.2 22.2 S.C. 17.7 17.7 18.0 18.1 18.1 18.1 18.4 18.5 18.5 18.6 18.9 19.0
K.W 1.83 1.81 1.80 1.79 1.86 1.84 1.83 1.82 1.87 1.85 1.84 1.83
85 T.C. 27.3 25.1 23.0 21.1 27.5 25.3 23.2 21.3 27.6 25.5 23.4 21.4 S.C. 17.6 17.7 18.0 18.1 18.1 18.2 18.5 18.6 18.6 18.7 19.0 19.1
K.W 2.04 2.00 1.99 1.98 2.15 2.04 2.02 2.01 2.07 2.05 2.03 2.02
95 T.C. 25.6 23.6 21.6 20.0 25.8 23.8 21.8 20.1 26.0 24.0 21.9 20.3 S.C. 17.3 17.4 17.6 18.0 17.8 17.9 18.2 18.5 18.4 18.4 18.7 19.0
K.W 2.24 2.23 2.21 2.20 2.28 2.26 2.24 2.23 2.29 2.27 2.25 2.24
105 T.C. 23.9 22.0 20.1 18.5 24.0 22.1 20.4 18.7 24.1 22.2 20.5 18.8 S.C. 16.9 16.9 17.1 17.3 17.4 17.5 18.0 17.8 18.0 18.0 18.4 18.3
K.W 2.50 2.48 2.47 2.46 2.53 2.52 2.50 2.49 2.55 2.53 2.51 2.50
115 T.C. 22.1 20.3 18.7 17.1 22.3 20.5 18.8 17.5 22.3 20.7 19.0 17.7 S.C. 16.5 16.5 16.8 16.7 17.1 17.2 17.3 17.3 17.7 17.8 17.9 17.6
K.W 2.82 2.80 2.78 2.78 2.85 2.83 2.81 2.81 2.86 2.84 2.83 2.82
125 T.C. 20.3 18.6 17.3 15.7 20.6 18.9 17.2 16.3 20.5 19.2 17.5 16.6 S.C. 16.1 16.1 16.5 16.1 16.8 16.9 16.6 16.8 17.4 17.6 17.4 16.9
K.W 3.14 3.12 3.09 3.10 3.17 3.14 3.12 3.13 3.17 3.15 3.15 3.14
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHB08 G2FD024(S,H)17 0.98 0.98 0.96
N1AHB08 G2FD030(S,H)17 0.98 0.98 0.96
N1AHB08 G2FD035(S,H)14 0.98 0.98 0.96
N1VSB12 G2FD024(S,H)17 1.01 1.01 0.87
F2RP/F2FP024 0.98 0.98 0.96
G2FD024(S,H)14 0.98 0.98 0.96
G2FD024(S,H)17 0.98 0.98 0.96
G1HD024 0.98 0.98 0.96
G1UA030S14 0.97 0.97 0.96
G1UA036S17 1.00 1.00 0.96
G1UA036S21 1.00 1.00 0.96
G2FD030(S,H)17 0.98 0.98 0.96
G2FD035(S,H)14 0.98 0.98 0.96
G1FA030S14 0.97 0.97 0.96
G1FA036S17 1.00 1.00 0.96
G1FA036S21 1.00 1.00 0.96

036-21031-004 Rev. A (0603)
12 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH030S06
INDOOR COIL MODEL NO. G2FD030(S,H)17
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 950 1050 1150
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 33.2 30.6 28.1 25.8 33.4 30.9 28.4 26.0 33.6 31.0 28.6 26.2 S.C. 21.1 21.1 21.4 21.6 21.7 21.8 22.1 22.2 22.4 22.5 22.9 23.0
K.W 2.35 2.33 2.33 2.31 2.39 2.37 2.36 2.34 2.44 2.43 2.41 2.40
85 T.C. 31.9 29.4 26.9 24.8 32.2 29.6 27.2 25.0 32.3 29.8 27.5 25.2 S.C. 20.7 20.8 21.1 21.2 21.4 21.5 21.9 22.0 22.1 22.2 22.6 22.7
K.W 2.57 2.55 2.54 2.53 2.65 2.59 2.57 2.56 2.66 2.64 2.62 2.61
95 T.C. 30.3 28.0 25.7 23.6 30.6 28.2 25.9 23.8 30.7 28.4 26.1 24.1 S.C. 20.2 20.4 20.7 20.9 21.1 21.2 21.5 21.6 21.7 21.9 22.2 22.3
K.W 2.89 2.87 2.85 2.84 2.92 2.90 2.88 2.87 2.98 2.96 2.94 2.93
105 T.C. 28.7 26.4 24.2 22.3 28.8 26.6 24.5 22.5 29.0 26.8 24.6 22.7 S.C. 19.8 19.8 20.1 20.2 20.6 20.7 21.0 21.0 21.3 21.3 21.6 21.6
K.W 3.28 3.25 3.24 3.22 3.30 3.28 3.27 3.25 3.36 3.35 3.33 3.31
115 T.C. 27.0 24.8 22.8 21.0 27.2 25.1 23.0 21.3 27.3 25.3 23.2 21.6 S.C. 19.3 19.4 19.6 19.7 20.1 20.2 20.3 20.3 20.9 21.0 21.1 21.0
K.W 3.74 3.72 3.69 3.67 3.76 3.75 3.73 3.71 3.83 3.80 3.79 3.77
125 T.C. 25.3 23.2 21.4 19.7 25.5 23.5 21.6 20.1 25.6 23.8 21.7 20.6 S.C. 18.8 18.9 19.2 19.3 19.7 19.7 19.6 19.7 20.5 20.6 20.6 20.4
K.W 4.20 4.19 4.15 4.12 4.22 4.22 4.19 4.18 4.30 4.26 4.25 4.23
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHB12 G2FD036(S,H)17 1.03 1.03 1.00
N1VSB12 G2FD030(S,H)17 1.03 1.03 0.89
N1VSB12 G2FD036(S,H)17 1.03 1.03 0.88
F2RP/F2FP030 1.00 1.00 0.94
F2RP/F2FP036 1.02 1.02 0.97
G1UA036S17,21 2 1.00 1.00 0.94
G1HD036 1.02 1.02 0.97
G1UA036S14 1.00 1.00 0.94
G2FD035(S,H)14 1.01 1.02 0.95
G2FD036(S,H)17 1.02 1.03 0.93
G2FD036(S,H)21 1.02 1.02 0.93
G1FA036S17,21 1.00 1.00 0.94
G1FA036S14 1.00 1.00 0.94

036-21031-004 Rev. A (0603)
Unitary Products Group 13
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH036S06
INDOOR COIL MODEL NO. F2RP/F2FP036
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1150 1250 1350
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 40.5 37.4 34.3 31.6 40.8 37.7 34.7 31.9 41.0 37.9 35.0 32.1 S.C. 25.6 25.7 26.0 26.3 26.5 26.8 27.1 27.2 27.5 27.6 28.2 28.2
K.W 2.65 2.63 2.63 2.60 2.69 2.67 2.66 2.64 2.78 2.77 2.74 2.74
85 T.C. 38.8 35.8 32.8 30.2 39.1 36.1 33.2 30.5 39.3 36.3 33.5 30.8 S.C. 25.0 25.0 25.4 25.6 25.9 26.0 26.5 26.6 26.9 27.0 27.4 27.6
K.W 2.86 2.86 2.84 2.83 2.90 2.89 2.87 2.86 3.00 2.98 2.96 2.94
95 T.C. 37.2 34.3 31.6 28.9 37.5 34.6 31.9 29.2 37.6 34.9 32.1 29.6 S.C. 24.3 24.6 25.0 24.9 25.5 25.6 26.0 25.9 26.3 26.7 26.9 26.9
K.W 3.27 3.23 3.21 3.21 3.28 3.26 3.25 3.24 3.39 3.36 3.34 3.34
105 T.C. 35.5 32.7 30.1 27.6 35.7 33.0 30.3 27.9 35.9 33.2 30.5 28.2 S.C. 23.8 23.9 24.2 24.3 24.9 25.0 25.2 25.3 25.9 25.9 26.1 26.1
K.W 3.74 3.71 3.69 3.67 3.75 3.73 3.72 3.70 3.84 3.84 3.82 3.80
115 T.C. 33.8 31.1 28.6 26.3 34.0 31.4 28.9 26.6 34.2 31.6 29.0 27.1 S.C. 23.2 23.3 23.6 23.9 24.3 24.3 24.5 24.5 25.3 25.3 25.5 25.6
K.W 4.30 4.28 4.25 4.21 4.31 4.31 4.29 4.26 4.43 4.40 4.38 4.36
125 T.C. 32.1 29.5 27.1 25.0 32.3 29.8 27.5 25.3 32.5 30.0 27.5 26.0 S.C. 22.6 22.7 23.0 23.5 23.7 23.6 23.8 23.7 24.7 24.7 24.9 25.1
K.W 4.86 4.85 4.81 4.75 4.87 4.89 4.86 4.82 5.02 4.96 4.94 4.92
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHB12 G2FD036(S,H)17 1.00 1.00 1.01
N1VSB12 G2FD036(S,H)17 1.01 1.01 0.96
F2RP042 1.00 1.00 1.01
G1UA048S21 1.02 1.02 1.02
G1UA048S17 1.01 1.01 1.01
G2FD42(S,H)21 1.01 1.01 1.01
G2FD046(S,H)17 1.01 1.01 1.01
G2FD036(S,H)21 1.00 1.00 1.01
G2FD036(S,H)17 1.00 1.00 1.01
G1FA048S21 1.02 1.02 1.02
G1FA048S17 1.01 1.01 1.01

036-21031-004 Rev. A (0603)
14 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH042S06
INDOOR COIL MODEL NO. F2RP/F2FP042
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1200 1400 1600
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 48.1 44.3 40.6 37.1 48.4 44.6 40.9 37.5 48.7 45.0 41.2 37.8 S.C. 30.2 30.2 30.9 31.1 31.1 31.3 31.8 32.3 32.1 32.4 32.9 33.1
K.W 3.09 3.06 3.03 3.01 3.27 3.25 3.22 3.19 3.54 3.51 3.48 3.46
85 T.C. 45.9 42.3 38.7 35.4 46.2 42.6 39.0 35.7 46.5 42.9 39.3 36.0 S.C. 29.5 29.7 30.1 30.4 30.4 30.6 31.1 31.2 31.4 31.6 32.2 32.2
K.W 3.33 3.31 3.28 3.25 3.52 3.49 3.46 3.44 3.78 3.75 3.73 3.70
95 T.C. 43.1 39.7 36.3 33.3 43.4 40.0 36.7 33.6 43.6 40.2 37.0 33.9 S.C. 28.4 28.6 29.0 29.3 29.4 29.6 30.1 30.2 30.4 30.6 31.2 31.2
K.W 3.69 3.67 3.64 3.61 3.88 3.85 3.82 3.79 4.14 4.11 4.08 4.06
105 T.C. 40.3 37.1 34.0 31.1 40.6 37.4 34.3 31.5 40.8 37.7 34.5 31.8 S.C. 27.4 27.5 28.2 28.3 28.5 28.6 29.0 29.3 29.5 29.9 30.0 30.2
K.W 4.11 4.09 4.05 4.02 4.30 4.27 4.24 4.22 4.56 4.53 4.50 4.47
115 T.C. 37.6 34.6 31.7 29.0 37.9 34.9 32.0 29.4 38.0 35.1 32.2 30.3 S.C. 26.5 26.7 27.0 27.1 27.7 27.7 28.0 28.1 28.7 28.7 29.0 29.3
K.W 4.60 4.57 4.54 4.50 4.78 4.76 4.72 4.69 5.04 5.02 4.99 4.98
125 T.C. 34.9 32.1 29.4 26.9 35.2 32.4 29.7 27.3 35.2 32.5 29.9 28.8 S.C. 25.6 25.9 25.8 25.9 26.9 26.8 27.0 26.9 27.9 27.5 28.0 28.4
K.W 5.09 5.05 5.03 4.98 5.26 5.25 5.20 5.16 5.52 5.51 5.48 5.49
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHC16 G2FD042(S,H)21 1.00 1.00 0.99
N1AHC16 G2FD048(S,H)21 1.03 1.02 0.99
N1VSC16 G2FD042(S,H)21 1.01 1.01 0.94
N1VSC16 G2FD048(S,H)21 1.04 1.04 0.95
F2FP048 1.03 1.02 0.99
G2FD042(S,H)21 1.00 1.00 0.99
G1UA048S21 1.01 1.01 0.98
G1UA048S17 1.01 1.01 0.99
G1UA046S17 1.01 1.01 0.99
G2FD048(S,H)21 1.03 1.02 0.99
G2FD048(S,H)24 1.03 1.02 0.99
G1FA048S21 1.01 1.01 0.98
G1FA048S17 1.01 1.01 0.99
G1FA046S17 1.01 1.01 0.99

036-21031-004 Rev. A (0603)
Unitary Products Group 15
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E5FH048S06
INDOOR COIL MODEL NO. F2FP048
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1450 1600 1750
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 54.5 50.2 46.0 42.1 55.1 50.9 46.6 42.7 55.6 51.3 47.1 43.4 S.C. 35.6 35.8 36.3 36.5 37.1 37.3 37.8 38.1 38.5 38.7 39.3 39.9
K.W 3.82 3.76 3.71 3.67 3.92 3.86 3.81 3.76 3.98 3.92 3.87 3.82
85 T.C. 52.7 48.6 44.5 40.7 53.3 49.2 45.1 41.5 53.8 49.6 45.5 42.0 S.C. 34.8 35.0 35.5 35.6 36.3 36.5 37.0 37.4 37.6 37.8 38.4 38.9
K.W 4.18 4.11 4.06 4.01 4.28 4.21 4.16 4.12 4.34 4.27 4.21 4.17
95 T.C. 50.3 46.4 42.5 38.8 50.9 47.0 43.0 39.6 51.4 47.4 43.4 40.0 S.C. 33.5 33.9 34.3 34.4 35.1 35.3 35.7 36.3 36.4 36.6 37.1 37.6
K.W 4.56 4.50 4.44 4.40 4.67 4.60 4.54 4.50 4.73 4.66 4.60 4.55
105 T.C. 47.9 44.1 40.4 37.0 48.4 44.7 40.9 37.6 48.9 45.0 41.3 38.1 S.C. 32.4 32.5 33.0 33.3 33.7 33.9 34.3 34.8 35.1 35.2 35.9 36.1
K.W 4.81 4.75 4.69 4.65 4.92 4.85 4.79 4.75 4.98 4.91 4.85 4.80
115 T.C. 45.3 41.6 38.1 34.8 45.7 42.1 38.5 35.5 46.0 42.4 38.8 35.8 S.C. 30.8 31.0 31.4 31.6 32.1 32.2 32.6 33.1 33.2 33.3 33.8 34.2
K.W 5.32 5.26 5.21 5.17 5.42 5.36 5.30 5.27 5.48 5.41 5.36 5.32
125 T.C. 42.7 39.1 35.8 32.6 43.0 39.5 36.1 33.4 43.1 39.8 36.3 33.5 S.C. 29.2 29.5 29.8 29.9 30.5 30.5 30.9 31.4 31.3 31.4 31.7 32.3
K.W 5.83 5.77 5.73 5.69 5.92 5.87 5.81 5.79 5.98 5.91 5.87 5.84
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHC16 G2FD048(S,H)21 1.01 1.01 1.00
N1AHD20 G2FD060(S,H)24 1.02 1.02 1.00
N1VSC16 G2FD048(S,H)21 1.02 1.02 0.93
N1VSD20 G2FD060(S,H)24 1.04 1.04 0.93
F2V060 1.03 1.03 0.93
F2FP060 1.01 1.01 1.04
G2FD048(S,H)21 1.01 1.01 1.00
G2FD048(S,H)24 1.01 1.01 1.00
G1UA048S21 1.00 1.00 1.00
G1UA060S21 1.01 1.01 1.00
G1UA060S24 1.01 1.01 1.00
G2FD060(S,H)24 1.02 1.02 1.00
G1FA048S21 1.00 1.00 1.00
G1FA060S21 1.01 1.01 1.00
G1FA060S24 1.01 1.01 1.00

036-21031-004 Rev. A (0603)
16 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. E4FH060S06
INDOOR COIL MODEL NO. G2FD060(S,H)24
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1700 1850 2000
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 65.8 60.8 55.8 51.2 66.2 61.2 56.3 51.9 66.6 61.7 56.8 52.4 S.C. 41.6 41.9 42.5 42.7 43.0 43.3 44.0 44.6 44.6 44.9 45.8 46.2
K.W 4.57 4.52 4.47 4.43 4.64 4.59 4.54 4.49 4.69 4.65 4.59 4.55
85 T.C. 64.3 59.4 54.5 50.1 64.9 60.0 55.1 50.7 65.3 60.4 55.7 51.2 S.C. 40.9 41.1 41.8 42.3 42.7 43.0 43.6 44.0 44.1 44.4 45.4 45.6
K.W 4.92 4.87 4.82 4.85 4.98 4.93 4.88 4.83 5.04 4.99 4.94 4.90
95 T.C. 62.4 57.5 52.8 48.5 62.8 58.0 53.3 49.0 63.2 58.4 53.8 49.4 S.C. 40.3 40.4 41.2 41.5 41.7 42.0 42.8 43.1 43.4 43.6 44.3 44.4
K.W 5.40 5.36 5.30 5.25 5.46 5.42 5.36 5.31 5.53 5.48 5.43 5.38
105 T.C. 60.1 55.4 50.7 46.6 60.5 55.9 51.4 47.1 60.8 58.3 51.8 47.8 S.C. 39.4 39.5 40.1 40.6 41.0 41.2 42.0 41.9 42.5 42.8 43.4 43.7
K.W 5.96 5.91 5.85 5.79 6.03 5.98 5.92 5.87 6.08 6.04 5.98 5.92
115 T.C. 57.6 53.1 48.6 44.6 58.0 53.5 49.3 45.1 58.3 53.8 49.7 45.6 S.C. 38.5 38.7 39.1 39.3 40.1 40.3 41.1 41.1 41.6 41.7 42.6 42.6
K.W 6.58 6.53 6.47 6.41 6.65 6.59 6.53 6.48 6.70 6.03 6.59 6.54
125 T.C. 55.1 50.8 46.5 42.6 55.5 51.1 47.2 43.1 55.8 49.3 47.6 43.4 S.C. 37.6 37.9 38.1 38.0 39.2 39.4 40.2 40.3 40.7 40.6 41.8 41.5
K.W 7.20 7.15 7.09 7.03 7.27 7.20 7.14 7.09 7.32 6.02 7.20 7.16
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
N1AHD20 G2FD060(S,H)24 1.00 1.00 1.00
N1AHD20 G2FD061H24 1.01 0.99 1.01
N1VSD20 G2FD060(S,H)24 1.04 1.02 0.96
N1VSD20 G2FD061H24 1.03 0.99 0.92
F2FP060 0.98 1.00 1.01
F2FV060H24 1.02 1.02 0.94
G1UA060S21 0.98 0.98 1.01
G1UA060S24 0.98 0.98 1.01
G2FD061H24 1.01 0.99 1.01
G1FA060S21 0.98 0.98 1.01
G1FA060S24 0.98 0.98 1.01

036-21031-004 Rev. A (0603)
Unitary Products Group 17
Multipliers for determining the performance with other indoor sections.
HEATING PERFORMANCE DATA
CONDENSING UNIT MODEL NO. E4FH018S06
EVAPORATOR COIL MODEL NO. F2RP/F2FP024
AIR TEMP.
ENTERING
OUTDOOR
UNIT
AIR TEMP.
ENTERING
INDOOR
COIL
ID CFM
600 650 700
MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.
60 60 25.01.834.1025.31.824.1725.51.804.24 70 22.41.883.5623.11.883.6823.81.883.79
80 19.81.953.0421.01.973.1922.11.983.35
47 60 20.81.723.5521.41.743.6122.01.763.67 70 18.51.773.0819.51.793.2020.51.813.32
80 16.41.842.6217.71.862.8019.01.882.97
40 60 19.01.633.3819.51.643.4619.91.643.54 70 17.01.732.8717.61.742.9418.21.763.01
80 15.01.862.3515.61.892.4116.31.912.48
30 60 16.01.562.9716.61.523.1617.31.493.36 70 14.11.682.4314.91.672.5815.71.662.73
80 11.9 1.86 1.85 12.8 1.90 1.95 13.8 1.94 2.05
17 60 12.01.532.3012.41.582.3112.91.622.32 70 10.5 1.53 2.02 11.3 1.58 2.10 12.1 1.63 2.18
80 9.1 1.54 1.73 10.2 1.59 1.89 11.3 1.63 2.03
10 60 9.8 1.501.9610.31.552.0110.91.592.06 70 8.7 1.48 1.76 9.4 1.53 1.84 10.1 1.58 1.92
80 7.6 1.47 1.56 8.5 1.52 1.68 9.3 1.56 1.79
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP018 0.87 0.93 0.94
G2FD024(S,H)14,17 0.97 0.94 1.04
G2FD030(S,H)17 1.02 0.95 1.06
G2FD035(S,H)14 1.02 0.95 1.06

036-21031-004 Rev. A (0603)
18 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
HEATING PERFORMANCE DATA
CONDENSING UNIT MODEL NO. E4FH024S06
EVAPORATOR COIL MODEL NO. F2RP/F2FP030
AIR TEMP.
ENTERING
OUTDOOR
UNIT
AIR TEMP.
ENTERING
INDOOR
COIL
ID CFM
750 800 850
MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.
60 60 29.0 2.17 4.06 29.3 2.13 4.17 29.6 2.09 4.29 70 28.3 2.33 3.68 28.8 2.29 3.81 29.3 2.26 3.94
80 27.6 2.54 3.29 28.3 2.50 3.44 29.0 2.46 3.58
47 60 24.6 1.99 3.62 25.1 1.98 3.72 25.7 1.97 3.82 70 23.5 2.13 3.23 24.0 2.12 3.32 24.5 2.11 3.41
80 22.5 2.31 2.85 22.9 2.30 2.92 23.3 2.28 2.99
40 60 22.8 1.92 3.43 23.0 1.92 3.47 23.3 1.91 3.52 70 21.4 2.04 3.02 21.4 2.03 3.06 21.5 2.01 3.09
80 19.9 2.20 2.62 19.8 2.17 2.64 19.7 2.14 2.65
30 60 18.2 1.77 2.96 18.6 1.76 3.03 18.9 1.75 3.10 70 17.7 1.91 2.66 17.7 1.89 2.69 17.7 1.88 2.71
80 17.2 2.09 2.36 16.8 2.07 2.34 16.5 2.04 2.32
17 60 12.9 1.59 2.39 13.2 1.59 2.44 13.4 1.59 2.48 70 12.7 1.72 2.16 12.9 1.72 2.20 13.1 1.72 2.24
80 12.5 1.89 1.93 12.6 1.89 1.96 12.8 1.88 1.99
10 60 10.7 1.49 2.20 10.9 1.50 2.22 11.1 1.51 2.25 70 10.2 1.62 1.92 10.3 1.63 1.94 10.4 1.63 1.96
80 9.6 1.79 1.64 9.7 1.79 1.65 9.8 1.80 1.66
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP024 1.00 1.00 1.00
G2FD035(S,H)14 1.00 1.02 0.98
G2FD030(S,H)17 1.00 1.02 0.98
G2FD024(S,H)14,17 0.99 0.97 1.02

036-21031-004 Rev. A (0603)
Unitary Products Group 19
Multipliers for determining the performance with other indoor sections.
HEATING PERFORMANCE DATA
CONDENSING UNIT MODEL NO E4FH30S06
EVAPORATOR COIL MODEL NO G2FD030(S,H)17
AIR TEMP.
ENTERING
OUTDOOR
UNIT
AIR TEMP.
ENTERING
INDOOR
COIL
ID CFM
950 1050 1150
MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.
60 60 33.72.534.0233.92.514.0934.12.494.16 70 26.42.673.6633.12.663.7633.82.653.87
80 25.72.853.2932.32.843.4333.52.833.56
47 60 23.02.343.6229.22.333.6829.62.573.74 70 22.02.463.2628.02.463.3328.62.703.40
80 21.02.612.8926.82.622.9827.62.873.06
40 60 21.32.253.4126.82.383.4527.12.263.48 70 19.92.353.0625.22.503.1025.62.363.13
80 18.62.482.6923.62.652.7324.02.492.77
30 60 17.22.312.8122.82.332.8623.32.342.92 70 16.72.412.5521.62.432.5922.02.442.62
80 16.22.552.2720.12.562.2820.42.582.29
17 60 12.22.082.4317.62.102.4618.02.122.48 70 12.02.192.1616.42.212.1816.82.232.21
80 11.8 2.31 1.90 15.2 2.34 1.92 15.6 2.36 1.95
10 60 10.11.972.2515.12.002.2715.52.042.30 70 9.6 2.061.9313.62.091.9713.92.131.98
80 9.1 2.171.6312.22.191.6812.52.231.69
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP030 1.00 1.01 0.99
F2RP/F2FP036 1.00 1.01 0.99
G2FD035(S,H)14 1.00 1.01 0.99
G1HD036 1.00 1.01 0.99
G2FD036(S,H)17 1.00 1.01 0.99
G2FD036(S,H)21 0.99 1.00 0.99
G1UA036S14 1.00 1.01 0.99
G1FA036S14 1.00 1.01 0.99
G1UA036S17,21 1.00 1.01 0.99
G1FA036S17,21 1.00 1.01 0.99

036-21031-004 Rev. A (0603)
20 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
HEATING PERFORMANCE DATA
CONDENSING UNIT MODEL NO. E4FH036S06
EVAPORATOR COIL MODEL NO. F2RP/F2FP036
AIR TEMP.
ENTERING
OUTDOOR
UNIT
AIR TEMP.
ENTERING
INDOOR
COIL
ID CFM
1150 1250 1350
MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P.
60 60 43.3 3.53 3.69 43.4 3.52 3.71 43.5 3.51 3.73 70 41.2 3.67 3.38 42.2 3.68 3.45 43.1 3.69 3.51
80 39.2 3.86 3.05 40.9 3.89 3.17 42.7 3.91 3.29
47 60 37.31 3.26 3.36 37.5 3.26 3.38 37.7 3.79 3.39 70 35.18 3.39 3.05 36.0 3.41 3.10 36.8 3.97 3.15
80 33.08 3.56 2.73 34.5 3.59 2.82 35.9 4.18 2.91
40 60 33.9 3.13 3.15 34.3 3.43 3.17 34.7 3.17 3.19 70 32.0 3.23 2.88 32.7 3.58 2.91 33.4 3.29 2.95
80 29.8 3.37 2.57 30.8 3.77 2.62 31.8 3.45 2.68
30 60 28.9 2.95 2.83 29.6 2.98 2.87 30.3 3.01 2.91 70 27.1 3.01 2.60 28.0 3.05 2.65 28.8 3.10 2.69
80 24.8 3.10 2.31 25.7 3.16 2.35 26.6 3.22 2.40
17 60 23.7 2.65 2.62 24.1 2.69 2.63 24.6 2.74 2.63 70 21.3 2.73 2.28 21.8 2.78 2.30 22.3 2.83 2.32
80 19.0 2.81 1.98 19.6 2.87 2.00 20.2 2.93 2.03
10 60 20.4 2.52 2.44 21.1 2.58 2.46 21.7 2.64 2.48 70 17.6 2.57 2.06 18.5 2.63 2.11 19.1 2.70 2.13
80 15.0 2.62 1.72 16.1 2.68 1.81 16.6 2.75 1.81
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP042 1.00 1.00 1.00
G2FD036(S,H)17,21 1.00 0.91 1.10
G2FD042(S,H)21 1.00 0.91 1.09
G2FD046(S,H)17 1.00 0.91 1.09