YoYo cam G33 User manual

QUICK START GUIDE
YOYOCam 3G Indoor
Model G33
GSM/3G Remote Surveillance Camera
www.yoyomotion.com
YOYOCam G33 Status Indicator
LED Status
Searching for network / SIM PIN lock enabled
Alarm triggered
No SIM card / System error / charging (power switch off)
Arming (20seconds to armed state)
Armed
Disarmed / Waiting for Master to register
Sending messages / Ongoing voice call
Factory reset
Key
Fast flash (two flashes per second)
Slow flash (one flash per second)
Two second flash
Two quick flashes every 2 seconds
On
Note: Send #31#0# to disable status indicator LED, #31#1# to enable it (default).
YOYOCam G33 Features
Insert a SIM card, perform a few simple configuration steps and YOYOCam is ready to guard
your property.
Schedule image
sending and arming
Get to know YOYOCam G33
Power
switch
Infrared body
detector
hite LED lights
Camera
Microphone
Mount/tripod
screw
Fold-out
stand
Battery
compartment
cover
Power cable
holes
Status indicator
GSM/3G antenna
Temperature
sensor socket
ON
OFF
Antenna
connector
Temperature
sensor
Light Sensor
ON
OFF
ON
OFF
Built in Stand
Mounting Bracket
©Copyright, March 2015 YOYOMotion AB. All rights reserved.
Web Rev F
GSM & 3G built in
Alarm by MMS
with images
Alarm by Email
with images
Infrared body
detector
Dial YOYOCam
and listen in
White LED lights
enable the camera
to capture images
in the dark
Request image
any time
Temperature monitoring
+
__
!
03
2
+
*Search for YOYOCam 3G Indoor on the App StoreSM or Google PlayTM
Easy control via SMS
or APP* Power outage
alert
Battery backup
(rechargable)
Alarm by SMS
(text)
Un-clip the stand and rotate backwards.

STEP 1. Prepare YOYOCam G33
1. To attach the antenna, align the plug with the antenna connector and screw it on gently by
hand until it is finger tight. Do not use tools. To remove it, gently unscrew the nut by hand.
2. Press gently on the raised dots and slide the cover downwards.
3. Lift the battery cover away from the device.
Battery
4. Move the battery out of the way as shown.
5. Insert the SIM card as indicated in the picture below.
•NOTE: The SIM PIN must be disabled. Use a mobile phone to check and, if necessary,
turn off SIM Lock.
•NOTE: Check that the SIM card has credit and is enabled for MMS and mobile internet.
a) Slide the clip upwards in the
direction of the OPEN arrow (1).
b) Lift the clip (2).
c) Locate the SIM card in the
holder, gold contacts facing
down. Be careful not to push
the SIM card past the clip so
that it ends up inside YOYOCam.
d) Close the metal clip (3).
e) Slide the clip downwards (4) in
the direction of the LOCK arrow.
TIP: Pressing lightly on each side of the metal clip makes
it easier to click open and shut.
YOYOCam uses a standard size
SIM Card (not micro or nano size)
ARNING: Always be sure to switch off
YOYOCam and disconnect the power before
inserting or removing the SIM card. Do not touch
the gold contacts of the SIM Card.
6. 7/8.
Temperature
sensor
6. Insert the power connector and lead the power cable out to the left or right, as required.
7. Replace the battery. Locate the back cover as shown. Press upwards at the two points
indicated (not in the centre) to click it in to place.
8. Plug in the temperature sensor, if required. Use a standard 3.5mm stereo audio extension
cable if you wish to locate the sensor away from YOYOCam.
1. Mount the bracket on the wall, ceiling or other surface as required.
2. Attach YOYOCam to the threaded tip of the bracket.
3. Screw the round lock-nut towards YOYOCam to secure YOYOCam on the mount.
4. Loosen the screw so that the angle can be adjusted. (See illustration opposite).
5. Tighten the screw to fix YOYOCam in the desired position.
STEP 2. Mount YOYOCam G33
BUILT IN STAND
Un-clip the stand and rotate backwards. See illustration opposite.
MOUNTING BRACKET
STEP 3. Set Up YOYOCam G33
1. Plug the power adaptor in to an outlet.
2. Slide the power switch to the ON position to turn on YOYOCam.
3. After approximately 60 seconds, YOYOCam bleeps to indicate that the mobile network has
been found.
4. From your mobile phone, send an SMS with text
#00# to the
mobile number of YOYOCam’s SIM card. YOYOCam confirms
your phone as Master by SMS,
meaning that you have full
control over YOYOCam.
5. The SMS responses are in
Swedish by default.
Send
#36#1# to switch to English.
6. Arm YOYOCam
• Send an SMS with text
#01# to arm YOYOCam
• Send an SMS with text
#02# to disarm YOYOCam
ON
OFF
In the armed state, YOYOCam raises an alarm when the built-in infrared body sensor detects
movement. When the alarm is raised, YOYOCam sends an SMS to the Master followed by an
MMS with images. Alternatively, the images can be sent to pre-set E-mail addresses or
YOYOCam can make a call to pre-set telephone number. Image and alarm settings can be
configured – see Using YOYOCam G33 and Complete Command List .
Using YOYOCam G33
The easiest way to drive YOYOCam is to install our app YOYOCam 3G Indoor from the App
StoreSM or Google PlayTM. You can also drive YOYOCam from any kind of mobile phone via SMS
commands.
The default Password is 1234. Change the Password to your own 4-digit number, for example:
• #18#1234#0678# changes the default Password to 0678
As Master, you can add up to 4 Users who can arm/disarm YOYOCam and request images:
•
#07#UserNumber# adds UserNumber, for example #07#[phone]#
• #27#UserNumber# deletes UserNumber
Master and Users may arm and disarm YOYOCam:
•
#01# arms YOYOCam. Infrared body sensor is activated after a 20 second delay is
received.
•
#02# disarms YOYOCam. Infrared body sensor is turned off.
Master and Users can request an image to be sent using MMS:
•
#03# sends the MMS to the requestor (Master or User)
•
#03# Number# sends the MMS to Number (does not need to be a User)
• Default image quality is igh (1280 x 768)
Master and Users can call YOYOCam and listen in via the built-in microphone.
• The caller must send (i.e. not withhold) the mobile number on voice calls. YOYOCam
rejects withheld and unknown numbers with busy-tone.
Users do not receive alarms by default. The Master can enable alarms to users:
•
#32#1# enables SMS alarm to Users; #32#0# turns it off
•
#33#1# enables alarm images to Users; #33#0# turns it off
• By default YOYOCam sends 3 images at igh quality (1280 x 768) using MMS.
YOYOCam automatically configures MMS and Internet settings for most networks in
Scandinavia, Germany, France, Italy and Spain. Settings for other networks can be
configured manually.
To send images using Email, YOYOCam must be configured with settings for Internet, Email
sender address and Email Server. The simplest way is to create a new Gmail or Outlook.com
account for YOYOCam, then send the Email address and password:
• #62#gmail#EmailAddress#Password# for a Gmail account.
• #62#outlook#EmailAddress#Password# for an Outlook.com or otmail account.
You may need to additionally go in to the account settings for the Gmail or Outlook.com account
and enable SMTP.
For other Email services, please ask your provider for the parameters needed to send Email:
• #26#SenderAddress#Password#SMTPserverAddress #SMTP-port#SSL#TLS#
Note that SenderAddress might be a username. SMTP-port is usually 25, 465 or 587. SSL and
TLS take values 0 (OFF) or 1 (on).
YOYOCam is now operational.
Standard Micro
Nano

If the Master phone is lost or you want to set up YOYOCam again from the beginning, you can
use Factory Reset to set all settings and parameters back to the factory default. Following Factory
Reset you will need to set the Master user, re-enter any mobile network(MMS, Email) settings and
reconfigure all users etc. To perform Factory Reset:
1. Make sure YOYOCam is switched on, status armed or disarmed.
2. Press and hold the Reset key for 5 seconds until YOYOCam beeps.
3. You may now release the Reset key. Factory Reset is complete.
Alternatively, the Master can send #19#Password#
Reset
key
YOYOCam G33 - Complete Command List
Arm (active 20 seconds after command received) #01#
Disarm #02#
ARM AND DISARM (Master & User)
Capture & send back to me by MMS #03#
Capture & send to Number by MMS #03#Number#
Capture & send to Master Email #05# (Sent by Master)
Capture & send to Master Email and User Email List #05# (Sent by User)
Capture & send to EmailAddress #05#EmailAddress#
GET IMAGE (Master & User)
Set me as Master (out of box / after factory reset) #00#
Master - transfer to a new phone number #14#NewMasterNumber#
Set/update Master’s Email address #09#EmailAddress#
Delete Master’s Email address #09#
DEFINE MASTER
Add User (UserNumber = User’s mobile number) #07#UserNumber#
Add Email to User Email List #07#EmailAddress#
Delete User #27#UserNumber#
Delete all Users and User Email List #27#
Change Password #18#OldPassword#NewPassword#
DEFINE USERS
Warning tone upon alarm - OFF #30#0#
Warning tone upon alarm - on #30#1#
SMS alert upon alarm - off #11#0#
SMS alert upon alarm - ON #11#1#
Message upon alarm - off #12#0#
MMS upon alarm – ON
(Contains images as per IMAGE SETTINGS below) #12#1#
Email upon alarm – off
(Contains images as per IMAGE SETTINGS below) #12#2#
Telephone call at Alarm - OFF #13#0#
Telephone call at Alarm - on #13#1#
SMS to Users - OFF #32#0#
SMS to Users - on #32#1#
Message to Users - OFF #33#0#
Message to Users – on
(Contains images as per
IMAGE SETTINGS below)
(MMS to Users or Email to User Email List,
with images, as set by #12# above) #33#1#
ALARM NOTIFICATIONS
Note: CAPITALS (eg. OFF) denote default setting
Get temperature from plug-in sensor #15#
Set temperature range to monitor #16#LoTemp# iTemp#
Temperature alert - OFF #15#0#
Temperature alert - on #15#1#
TEMPERATURE SENSOR
Scheduled arm/disarm - setting #41#Day#ArmTime#DisarmTime#
Scheduled arm/disarm - OFF #04#0#
Scheduled arm/disarm - on #04#1#
Scheduled image capture & send - setting
Mode: 0 - Email; 1 - MMS #43#Mode#Day#StartTime#EndTime#Interval#
Scheduled image capture & send - OFF #06#0#
Scheduled image capture & send - on #06#1#
SCHEDULED ACTIONS
Number of images in alarm message (1 to 5); default 3 #21#Quantity#
Size of image in alarm, get image or scheduled #22#Quality#
capture & send. Quality 1: Low (320 x 240),
2: Medium (640 x480), 3: igh (1280 x 768)(default)
IMAGE SETTINGS
off (never turned on) #20#0#
AUTO mode (on when dark and motion detected) #20#1#
Always (on whenever motion detected, even in bright light) #20#2#
LED LIGHTING SETTINGS
Get status #10#
Technical status report (firmware version, IMEI, signal) #40#
GET STATUS
Infrared body detector - off #17#0#
Infrared body detector - ON #17#1#
LED status indicator - off #31#0#
LED status indicator - ON #31#1#
Power change notification SMS - off #35#0#
Power change notification SMS - ON #35#1#
Language – English #36#1#
Language – SWEDIS #36#2#
Weak signal alert by SMS – OFF #37#0#
Weak signal alert by SMS – on
(requires enough signal to send an SMS) #37#1#
Forward SMS from unknown numbers to Master – ON #50#0#
Forward SMS from unknown numbers to Master – off #50#1#
Auto disarm after repeated alarms – OFF #55#0#
Auto disarm after n alarms – on #55#n#
ADVANCED SETTINGS
Day: 0 - Every day; 1 - Mon; 2 - Tue; 3 - Wed; 4 - Thu; 5 - Fri; 6 - Sat; 7 - Sun; 8 - Mon-Fri; 9 -
Weekend (Sat+Sun)
Check Email parameters #26#
Configure Email sending parameters (Gmail) #62#gmail#EmailAddress#Password#
Configure Email sending parameters #62#outlook#EmailAddress#Password#
(Outlook.com, otmail)
Configure Email sending parameters (other) #26#SenderAddress#password#STMPserver#
SMTP port#SSL#TLS#
CONFIGURE EMAIL SERVICE
MMS: Get current settings #25#
MMS: Configure parameters #25#MMSC#GatewayIP#WAPGatewayPort#
TTPGatewayPort#APN#APNusername#APNpassword#MMS#
Internet: Get current settings #24#
Internet: Configure parameters #24#APN# APNusername#APNpassword#MCC#MNC#
DataProxyIP#DataProxyPort#DEFAULT#
Reset MMS and Internet #54#
settings to default
Remote restart (reboot) #42#password#
Factory reset (wipes all settings and data #19#Password#
except wireless sensors and remotes).
RESET
Note: Internet service must also be configured to be able to send Email.
CONFIGURE MMS AND INTERNET SERVICE
YOYOCam automatically configures MMS and Internet settings for most networks in Scandinavia,
Germany, France, Italy and Spain. Settings for other networks can be configured
manually – see the User Guide.
Factory Reset

The status indicator is off
The back-up battery is flat or not connected and there is no external power.
•Check the battery connection and connect power
The status indicator stays on slow red blink
The SIM-card in YOYOCam has the PIN-lock enabled.
• Place the SIM card in a mobile phone to check and if necessary switch off PIN-lock
YOYOCam is out of reach for mobile network coverage.
• Try YOYOCam in different positions for better signal strength, or use a high-gain external
antenna with extension cable.
There is no SIM-card or it is not properly inserted.
• Check that the SIM card is inserted according to the instructions in STEP 1.
The SIM-card is inactive (expired, locked, not yet activated …).
•Check the SIM card in a mobile phone and contact your mobile operator if necessary
The status indicator is on green blink but YOYCam responds that a password is
required or that you are not valid user
YOYOCam has not yet got a registered Master.
• See STEP3 Setup YOYOCam G33
You are not the registered Master or a registered User.
• See
Using YOYOCam G33 to set up Users or change the Master
SMS-messages but no MMS or Email or images are received from YOYOCam.
YOYOCam was disarmed (by SMS, Remote orAPP) too quickly after detection / SMS notification
and the MMS or Email transmission was interrupted.
•Allow more time (until the status indicator has stopped blinking) before disarming
The SIM-card does not have MMS service activated at delivery.
• Easily done by sending an activation-SMS from a regular mobile phone with the
SIM-card inserted.
• Consult the homepage or contact your mobile operator.
The SIM-card is from a mobile operator for which YOYOCam does not know the settings.
•Get current MMS settings with #25#
•Set up MMS manually. See Mobile Network Settings section of the User Guide.
YOYOCam has been set up with manual MMS settings but they are wrong
•Get current settings by sending #25# to your YOYOCam’s mobile number. Compare with
the settings required for your mobile operator.
•Use #25# with parameters to correct the settings
Poor GSM/3G coverage. Signal strength is enough for SMS, but not for MMS, or Email.
• Relocate YOYOCam to a place with better coverage
• Try a SIM-card from another mobile operator
•Use a high-gain external antenna with extension cable
Your mobile operator’s MMS service cannot handle large images
• Reduce image size, for example send #22#2# to reduce it to 640x480 pixels
YOYOCam G33 Troubleshooting Guide
Email messages are not being received from YOYOCam
Email requires additional settings and mobile Internet service.
• (has never worked) Check that the Email account and server settings are correct
• Ensure that Email addresses are no longer than 33 characters
• Check that the SIM card has Mobile Internet service (put SIM in a smartphone and check web
browsing works)
• Check that the Mobile Internet settings are correct
Master receives SMS “External power lost...” followed by a new SMS
“External power, resumed”
AC power was temporarily cut. This can sometimes be caused by electrical machinery or heating
switching on or off, and getting detected by YOYOCam.
• This has no functional impact on YOYOCam. The built-in back-up battery keeps it running.
• The SMS power notifications can be switched off by sending #35#0# to your YOYOCam’s
mobile number.
Master receives SMS saying that an incoming message is being forwarded.
Incoming SMS from unregistered users are forwarded to the Master. This is a security precaution
in case someone is trying to access YOYOCam. This function is also useful if operators notify when
the credit is low.
The forwarding function can be turned off by sending #50#0# to your YOYOCam’s mobile number.
www.yoyomotion.com
© Copyright, March 2015 Yoyomotion AB. All rights reserved. Subject to change without notice.
App Store is a trademark of Apple Inc. All other trademarks are the property of their respective owners.
Important Information
Please read this information before using your YOYOCam.
S
Sa af fe et ty y a an nd d U Us sa ag ge e G Gu ui id de el li in ne es s
•Read the terms and conditions for your SIM card and mobile operator service.
•When inserting or removing the SIM card, do not touch the gold connectors.
• Use only the approved YOYOMotion AC power adaptor for YOYOCam G33.
• Treat your YOYOCam carefully; store it safely and do not drop or throw it.
• Do not expose your YOYOCam to dust, liquid, moisture or humidity.
•Do not use or store your YOYOCam at extreme high or low temperatures.
•Do not expose your YOYOCam to naked flames, lit tobacco products or other
heat sources.
•Do not use your YOYOCam in hospitals or near medical equipment.
•If you have personal medical devices such as a pacemaker, consult your physician and the
manufacturer for advice.
• Do not use your YOYOCam in aircraft or in any place where use of radio transmitters is
prohibited.
•Do not use your YOYOCam in places where a potentially explosive atmosphere is present.
•Do not use YOYOCam in proximity to car airbags.
• Do not attempt to take your YOYOCam apart; there are no user-serviceable components
inside the product.
• Do not allow children to play with your YOYOCam; small parts such as SIM cards could be
detached and represent a choking hazard.
•For optimum performance do not cover your YOYOCam; position it with good access to
the mobile signal.
• You should not rely on any voice call capability that your YOYOCam provides for
emergency or essential communications.
Battery
• Battery performance (device runtime) depends on signal strength, temperature, usage pattern
and other factors.
•The battery may have temporarily reduced capacity when new or after a prolonged period
without use.
• Turn off the device and unplug the power adaptor before removing or inserting the battery.
• Do not allow the battery contacts to touch any metal object or other conductor.
•Use only the supplied battery or accessory/service replacement battery from YOYOMotion.
Disposal and Recycling
• Do not dispose of your YOYOCam with normal household waste.
• Dispose of your YOYOCam at an appropriate collection point for electronic equipment.
• For more information, contact your local authority, your household waste collection depot
or the retailer where you bought your YOYOCam.
EU Regulatory Conformance
English: We fulfil the requirements of the R&TTE Directive (99/5/EC). Český: Výrobek
spleiuje požadavky smärnice R&TTE (99/5/EC). Dansk: Vi opfylder kravene i
R&TTE-direktivet (99/5/EC). Deutsch: Die Anforderungen der Richtlinie für Funk- und
Fernmeldegeräte (99/5/EG) werden erfüllt. Español: Cumplimos los requisitos de la
Directiva R&TTE (99/5/EC). Français: Ce produit est conforme à la directive R&TTE
(99/5/EC). Hrvatski: Mi ispunjavamo zahtjeve R&TTE Direktive (99/5/EC). Italiano: Il
prodotto soddisfa i requisiti della Direttiva R&TTE (99/5/EC). Magyar: Teljesítjük az R&TTE
irányelv (99/5/EC) követelményeit. Nederlands: We voldoen aan de vereisten die in de
R&TTE-richtlijn (99/5/EG) worden gesteld. Norsk: Vi oppfyller kravene i R&TTE-direktivet
(99/5/EC). Polski: Spełniamy wymagania dyrektywy R&TTE (99/5/WE). Português: São
cumpridos os requisitos da Directiva R&TTE (99/5/EC). PB Atendemos aos requisitos da
Diretriz R&TTE (99/5/EC). Română: Îndeplinim cerinţele directivei R&TTE (99/5/EC).
Slovenčina: Výrobok spĺňa požiadavky smernice R&TTE (99/5/EC). Suomi: Täytämme
radio- ja telepäätelaitedirektiivin (99/5/EY) asettamat vaatimukset. Svenska: Vi uppfyller
kraven i R&TTE-direktivet (99/5/EC). Ελληνικά: Πληρούµε τις απαιτήσεις της Οδηγίας
R&TTE (99/5/ΕΚ).