YOYOCam G3 User manual

QUICK START GUIDE
YOYOCam G3
GSM Remote Surveillance Camera
www.yoyomotion.com

YOYOCam G3 Features
Insert a SIM card, perform a few simple configuration steps and YOYOCam is ready to guard your property.
Infrared body detector and camera-
based movement detection
Infrared LED lights enable the camera to
capture images in the dark
Alarm by SMS (text), MMS and Email
(including images)
Dial YOYOCam and listen in
Receive images at pre-set intervals
according to a schedule
Simple configuration via SMS
commands; request images by SMS

Get to know YOYOCam G3
Power
switch
Infrared body
detector
Infrared LED lights
Camera
Microphone
Mount/tripod
screw
Fold-out
stand
Battery
compartment
cover
Power cable
holes
Status indicator
GSM antenna
Tempreture
sensor
ON
OFF
Antenna
connector

STEP 1. Prepare YOYOCam G3
1. An antenna is included and ready-mounted at delivery. To remove it, gently unscrew the nut by hand. To attach
it again or use a different antenna, align the plug with the antenna connector and screw it on gently by hand until
it is finger tight. Do not use tools.
2. Slide the battery compartment cover downwards.
3. Lift the battery cover away from the device.
4. Move the battery out of the way as shown.
•WARNING: Always be sure to switch off YOYOCam and disconnect the power before inserting or removing
the SIM card. Do not touch the gold contacts of the SIM Card.
•NOTE: The SIM PIN must be disabled. Use an ordinary mobile phone to check and, if necessary, turn off
SIM Lock.
•NOTE: Check that the SIM card has credit and is enabled for MMS.
5. Unlock and open the SIM card holder by sliding the clip upwards and then lifting it. Place the SIM card in the
holder as shown, gold contacts on the underside. Lower the retaining clip and lock it by sliding it downwards.
6. Insert the power connector and lead the power cable out to the left or right, as required.
7. Replace the battery and battery compartment cover.
Battery
1. 2. 3.
4. 5. 6.
OPEN
LOCK
SIM card
holder

1. Mount the bracket on the wall, ceiling or other surface as required.
2. Attach YOYOCam to the threaded tip of the bracket.
3. Screw the round lock-nut towards YOYOCam to secure YOYOCam on the mount.
4. Loosen the screw so that the angle can be adjusted.
5. Tighten the screw to fix YOYOCam in the desired position.
STEP 2. Mount YOYOCam G3
Note: The mount screw-thread is standard photographic size, so YOYOCam can, for example, be mounted
on a camera tripod.
Note: For best results, avoid pointing YOYOCam at bright lights or windows. See the User Guide for more tips.
BUILT IN STAND
Un-clip the stand and rotate backwards.
MOUNTING BRACKET
ON
OFF
ON
OFF

YOYOCam G3 Status Indicator
LED Status
Searching for network / SIM PIN lock enabled
Alarm triggered
No SIM card / System error / charging (power switch off)
Loading wireless remote sensor
Armed
Disarmed / Waiting for Master to register
Sending messages / Ongoing voice call
Factory reset / Loading wireless remote sensor
Key
Fast flash (two flashes per second)
Slow flash (one flash per second)
Two second flash
Note: Send #143#0# to disable status indicator LED, #143#1# to enable it (default).
STEP 3. Set Up YOYOCam G3
1. Plug the power adaptor in to a wall outlet or socket strip.
2. Slide the power switch to the ON position to turn on YOYOCam
3. After approximately 40 seconds, YOYOCam bleeps to indicate
that the GSM network has been found.
4. From your mobile phone, send an SMS with text
#00# to the mobile
number of YOYOCam’s SIM card. YOYOCam confirms your phone as
Master by SMS, meaning that you have full control over YOYOCam.
5. The SMS responses are in Swedish when a Swedish SIM is inserted,
otherwise English. Send #127#1# to switch to English.
6. Network MMS settings are configured automatically for the major
networks. If your network operator is in the table to the right, you
must now send the command indicated in order to configure MMS.
7. Arm YOYOCam
• Send an SMS with text
#01# to arm YOYOCam
• Send an SMS with text #02# to disarm YOYOCam
YOYOCam is now operational.
When armed, YOYOCam will raise the alarm when a sensor detects
an event. By default, the built-in infrared body sensor is enabled and
camera movement detection is disabled. When the alarm is raised,
YOYOCam sends an SMS to the Master followed by an MMS with
images. Other options include voice call and E-Mail alarms. Detector,
image and alarm settings can be configured – see Using YOYOCam G3
and Complete Command List.
Network Command to send
Operator
ACN #145#ACN#
Cell Mobile SE #145#CELLMOBILE#
Chess NO #145#C ESSNO#
Glocalnet #145#GLOCALNET#
alebop #145# ALEBOP#
Parlino #145#PARLINO#
Superstar #145#SUPERSTAR#
TDC Song NO #145#TDCNO#
TDC Song SE #145#TDCSE#
Telmore DK #145#TELMORE#
Universal #145#UNIVERSAL#
Ventelo NO #145#VENTELONO#
Ventelo SE #145#VENTELOSE#

Using YOYOCam G3
Users interact with YOYOCam using SMS commands and voice calls.
MASTER & USER
Up to 10 Users set up by the Master can access YOYOCam. Master and Users can send these commands:
Master & Users can also call YOYOCam and listen in via the built-in microphone.
Text to send What it does
#00# (after factory reset) sender becomes Master
#14#NewMasterNumber# Change from present Master number to NewMasterNumber
#04#OldPassword#NewPassword# Change the Guest password (default is 1234)
#06#UserNumber# Add a User.
#113#UserNumber# Delete a User
#106#EmergencyNumber# Add Emergency Number (called when emergency button pressed on remote)
#107#EmergencyNumber# Delete Emergency Number
#127#LanguageCode# Set Language. 0=Swedish (default); 1 = English
Text to send What it does
#01# Arm YOYOCam (if an event is detected, alarm is triggered)
#02# Disarm YOYOCam (events will be ignored)
#03# Take one image and send it to the requesting user
#03#Quantity# Take a number (Quantity 1-8) of images and send to requestor
#07# Check the settings and status (summary list by SMS)
#09# or #09#1# Get the command list (#09# for SMS, #09#1# for MMS response)
#32#Size# Set image size: 1: 160x128; 2: 320x240 (default); 3: 640x480
#33#Quantity# Set quantity of images to take when triggered: 1-8 (default 5; Note 1)
#118#0# or #118#1# Disable (0) infrared body detection; enable (1) (default)
#22#0# or #22#1# Disable (0) camera based motion detection (default); enable (1)
#39#0# Call mode – When Emergency button pressed, numbers are dialed
#39#1# SMS/MMS mode – when Emergency button is pressed, YOYOCam sends SMS and MMS.
#143#0# or #143#1# Disable (0) indicator LED; enable (1) (default)
For example, send #04#1234#6789# to change password to 6789. Send #06#0702222222# to add 0702222222
as a user.
YOYOCam has 3 user categories:
1- One “MASTER” who can perform all operations and receive all alarm messages.
2-Upto10“USERs” who can access all main functions but can not perform configuration commands.
3 - Unlimited number of “GUESTs” who only can request images.
NOTE: All need to have “visible” phone numbers and need to know YOYOCam’s mobile phone number.
Turn on and off the alarm function of YOYOCam:
• send SMS with text #01# to arm, or send #02# to disarm
• or press the “lock” button of the remote control to arm, and the “unlock” button to disarm.
Capture and send one or more images:
• send SMS with text #03# and receive one image in return
• or send SMS with text #30#NumberOrEmail#ImageQuantity# to send image(s) to someone else.
MASTER
There is one Master user who has complete control over YOYOCam. Master-only commands:

Download the User Guide & Do more with YOYOCam G3
For more information, download the full user guide from www.yoyomotion.com/camera.html and you can also find
out how to:
• Set an automatic arm/disarm schedule based on day and time.
• Set YOYOCam to automatically take and send images according to a day and time schedule.
• Add up to 15 wireless sensors such as temperature sensors, smoke detectors etc.
• Change advanced settings including image brightness, alarm notification method, MMS parameters.
Factory Reset
If the Master phone is lost or you want to set up YOYOCam again from the beginning, you can use Factory Reset to
set all settings and parameters back to the factory default. Following Factory Reset you will need to re-pair the
remote controls and any remote sensors, re-enter any mobile network (MMS) settings and reconfigure all users etc.
To perform Factory Reset:
1. Switch Off YOYOCam and wait at least 20 seconds.
2. Press and hold the Reset key.
3. Switch on YOYOCam while the Reset key is still pressed.
4. After approx. 10 seconds, YOYOCam bleeps twice and the indicator LED goes green and then flashes
red
5. You may now release the Reset key.
GUEST
Guest users are people who do not normally need access, but might be asked to check the protected area because
they are nearby, for example. Guest users do not need to be pre-defined to YOYOCam, but do require the PIN.
Guest commands:
Text to send What it does
#03#Password# Take one image and send it to the requesting guest
#03#Password#Quantity# Take a number (Quantity 1-8) of images (Note 1)
#30#Password#To#Quantity# Take a number (Quantity 1-8) of images and send to a phone or E-mail
address (To is the mobile number or E-Mail address; Note 1)
Note 1: Maximum Quantity is limited to 2 when image size is set to 3.
Reset
key

www.yoyomotion.com
© Copyright, 2012 YOYOMotion AB. All rights reserved.
Important Information
Please read this information before using your YOYOCam.
SSaaffeettyy aanndd UUssaaggee GGuuiiddeelliinneess
•Read the terms and conditions for your SIM card and mobile operator service.
• When inserting or removing the SIM card, do not touch the gold connectors.
• Use only the approved YOYOMotion AC power adaptor for YOYOCam G3.
• Treat your YOYOCam carefully; store it safely and do not drop or throw it.
• Do not expose your YOYOCam to dust, liquid, moisture or humidity.
• Do not use or store your YOYOCam at extreme high or low temperatures.
• Do not expose your YOYOCam to naked flames, lit tobacco products or other heat sources.
• Do not use your YOYOCam in hospitals or near medical equipment.
• If you have personal medical devices such as a pacemaker, consult your physician and the manufacturer for advice.
• Do not use your YOYOCam in aircraft or in any place where use of radio transmitters is prohibited.
• Do not use your YOYOCam in places where a potentially explosive atmosphere is present.
• Do not use YOYOCam in proximity to car airbags.
• Do not attempt to take your YOYOCam apart; there are no user-serviceable components inside the product.
• Do not allow children to play with your YOYOCam; small parts such as SIM cards could be detached and
represent a choking hazard.
• For optimum performance do not cover your YOYOCam; position it with good access to the mobile signal.
• You should not rely on any voice call capability that your YOYOCam provides for emergency or essential
communications.
Battery
• Battery performance (device runtime) depends on signal strength, temperature, usage pattern and other factors.
• The battery may have temporarily reduced capacity when new or after a prolonged period without use.
• Turn off the device and unplug the power adaptor before removing or inserting the battery.
• Do not allow the battery contacts to touch any metal object.
• Use only the supplied battery or accessory/service replacement battery from YOYOMotion.
Disposal and Recycling
• Do not dispose of your YOYOCam with normal household waste.
• Dispose of your YOYOCam at an appropriate collection point for electronic equipment.
• For more information, contact your local authority, your household waste collection depot or the retailer where
you bought your YOYOCam.
EU Regulatory Conformance
English: We fulfil the requirements of the R&TTE Directive (99/5/EC). Český: Výrobek spleiuje požadavky
smärnice R&TTE (99/5/EC). Dansk: Vi opfylder kravene i R&TTE-direktivet (99/5/EC). Deutsch: Die
Anforderungen der Richtlinie für Funk- und Fernmeldegeräte (99/5/EG) werden erfüllt. Español: Cumplimos
los requisitos de la Directiva R&TTE (99/5/EC). Français: Ce produit est conforme à la directive R&TTE
(99/5/EC). Hrvatski: Mi ispunjavamo zahtjeve R&TTE Direktive (99/5/EC). Italiano: Il prodotto soddisfa i
requisiti della Direttiva R&TTE (99/5/EC). Magyar: Teljesítjük az R&TTE irányelv (99/5/EC) követelményeit.
Nederlands: We voldoen aan de vereisten die in de R&TTE-richtlijn (99/5/EG) worden gesteld. Norsk: Vi
oppfyller kravene i R&TTE-direktivet (99/5/EC). Polski: Spełniamy wymagania dyrektywy R&TTE (99/5/WE).
Português: São cumpridos os requisitos da Directiva R&TTE (99/5/EC). PB Atendemos aos requisitos da
Diretriz R&TTE (99/5/EC). Română: Îndeplinim cerinţele directivei R&TTE (99/5/EC). Slovenčina: Výrobok
spĺňa požiadavky smernice R&TTE (99/5/EC). Suomi: Täytämme radio- ja telepäätelaitedirektiivin (99/5/EY)
asettamat vaatimukset. Svenska: Vi uppfyller kraven i R&TTE-direktivet (99/5/EC). Ελληνικά: Πληρούµε τις
απαιτήσεις της Οδηγίας R&TTE (99/5/ΕΚ).

Remote Control
Press to arm YOYOCam.
Press to disarm YOYOCam.
When the Emergency button is pressed, YOYOCam acknowledges with a bleep. By default, YOYOCam calls the
Master and each added Emergency number in turn until someone answers, at which point that person can hear the
audio from YOYOCam. YOYOCam tries each number up to three times before giving up. The Status Indicator LED
displays ongoing voice call.
Note: If YOYOCam is set to call a landline, check that hanging up the landline clears the call; some telephone
networks do not clear the call when the called end hangs up, making it impossible to dial a new call. It is
recommended that emergency calls are made to mobile numbers.
Alternatively, send
#39#1# to the mobile number of YOYOCam to set SMS/MMS mode. When the Emergency
button is pressed YOYOCam acknowledges with a bleep, and sends an SMS alert followed by an MMS with an
image to the Master and each added Emergency number.
Note: YOYOCam responds to the Emergency button in both Armed and Unarmed states. If YOYOCam is busy,
for example sending images, the ongoing operation is cancelled in order to action the Emergency alarm.
Pairing your YOYOCam with a Remote Control
The supplied Remote Controls are individually paired with YOYOCam at delivery. They can be paired manually e.g.
after a factory reset of YOYOCam or to use one Remote Control for several YOYOCams. Up to five remotes can be
used with each YOYOCam; two are supplied.
1. Ensure that YOYOCam is on the GSM network during this procedure: Status Indicator or .
2. Make a short (less than one second) press and release of the RESET key. YOYOCam bleeps and LED
flashes orange indicating pairing mode.
3. Press any button on the remote control. YOYOCam bleeps and LED turns green for 2 seconds then
returns to orange flashing ready to pair another remote control.
4. Press RESET to exit pairing mode. In any case pairing mode times out after 15 seconds.
Cover slides
open & closed
Arm
YOYOCam
Emergency
button
Disarm
YOYOCam
Indicator LED (lights
when any button
pressed to indicate
transmission