Yuel Beast Designs ATLAS Series User manual

CALYPSO
Calypso User guide Version 8

The performance-first design values of the ATLAS series, in a
smaller ITX footprint. The CALYPSO chassis gives you all the
watercooling potential needed for the current AND next
generation of hardware.
No longer choose between performance & aesthetics. Build up an
AIO, single custom loop, dual loop or hybrid to support even the
most demanding components.

Calypso Overall
Dimensions
338mm | 13.3"
450 mm | 17.75"
208mm | 8"
NO PSU

Calypso ATX
Assembly & Dimensions
Calypso SFX
Assembly & Dimensions
260mm | 11"
242mm | 9.5"
208mm | 8"

Calypso PSU Types
Calypso ATX PSU
Calypso SFX PSU
For ATX PSU
Mounting.
Supports two 2.5"
drive mounted either
horizontally or
vertically
For SFX PSU
Mountning.
Supports two 2.5"
drive mounted
horizontally

Calypso GPU
Disambiguation
Standard GPU Bracket
Adapter GPU Bracket & Armature
The Standard GPU Bracket supports regular GPU Mounting
for graphics cards up to 336mm Long
In order to recieive a regular Armature, an enhanced GPU
bracket must be used. This GPU bracket provides additional
graphics card clearance and supports lengths up to 360mm
Standard Armature
Enhanced GPU
Adapter Bracket
Standard
GPU Bracket

Calypso GPU
Mounting
Change your GPU mounting position based
on the number of PCIE slots your graphics
card occupies. The standard GPU Bracket
(Shown above) can accommodate up to 3
GPU positions (.8" movement).
The Adapter GPU bracket has even more
flexibility than the standard bracket and can
mount in 2X as many positions.

The Standard GPU Bracket is shown in its second of three
possible mounting positions. The distance from edge of GPU
Bracket to Radiator Panel varies based on where you decide
to mount the GPU bracket.
1'st Position (For single Slot cards) = 46mm
2nd Position = 26mm
3rd Position = 5mm
Standard gpu
Mounting clearance

The adapter GPU Bracket & Armature are shown in its closest
of seven mounting positions. The distance from edge of the
Armature to Radiator Panel varies based on where you
decide to mount the GPU bracket.
1'st Position = 61mm
2nd Position = 51mm
3rd Position = 41mm
4rth Position = 31mm
5th Position = 20mm
6th Position = 10mm
7th Position = .5mm
adapter & Armature
gpu Mounting clearance

adapter & Armature
gpu limitations
One of the few limitations of the Armature & GPU Adapter bracket is a
setup in which the wings are attached above and below the
motherboard while using a horizontal motherboard layout (The
standard GPU Bracket works fine in this and any orientation). The built
in solution to this is simply not using the raidator bracket for the side
with the GPU. Alternatively, you can also use unthreaded #6 standoffs
to move the radiator bracket farther away from the Armature &
Adapter GPU bracket.

Calypso Wing
The Calypso Wing allows for 240 & 280 radiator
mounting, with headroom clearance of 44mm
(240mm rad) and 24mm (280) respectively.
Additionally the 240mm radiator can jog 5mm, and
280mm radiator 9mm in either direction from
center.
328mm ID Dimension to flanges
Approximately 320mm to radiator
bracket attachment hardware

Calypso Radiator
Brackets
Hybrid Radiator
Bracket
Pump Radiator
Bracket
The Hybrid
radiator
brackets
unique design
allows for the
passthrough of
fittings and
bulkheads on
most radiators
The Pump
Radiator
bracket allow
for the
mounting of
any pump
matching a
40mm or
60mm
mounting
pattern

Calypso Radiator
Bracket mounting
Each Radiator Bracket supports 120mm, 140mm, 240mm,
280mm, and 360mm radiator pattern. A 360mm fan pattern
is joggable 14mm from center in either direction.
26mm
120
mm
446mm ID between Wings
419mm ID between hardware
412mm between Wing Flanges
All dimensions +/- 1mm
360mm Fan pattern on Center

Calypso Assembly
10-32 SHMS & Washer
for Wings
6-32 SHMS for
Motherboard
10-32 Hex Nut
for Wings
Wing
Motherboard Plate
Standard GPU
Bracket

Calypso Assembly
Continued
Note GPU Bracket
installtion is on this side of
the motherboard panel
I personally prefer the
motherboard plate to be
installed ontop of the
wings, but there is no right
or wrong way to install this
component
When assembling CALYPSO, it is important to not fully tighten all the components
until all peices are assembled in their relative positions. Only after this should you
go and tighten everything down with the aid of tools.

Calypso Assembly
Continued
10-32 SHMS / Washer
for SFX & ATX PSU
Hole for Power button
or Pass-through
Clearance holes for the 6-32
SHMS, Washer, & Hex nut for
Radiator Bracket attachment.
Each Radiator bracket has four
attachment points, two on each
wing

Calypso Assembly
Continued
Stabalizer brackets, prevents tipping in
alternative orientations

Troubleshooting and Notes to user
Each Calypso Package comes with a bag labeled
"Troubleshooting", this bag contains a 6-32 & 10-32 Type F
Screws. These screws are for clearing threads that might have
been compromised during powdercoating.
If you encounter a thread that is very tight, or a screw that
will not screw in, use the appropriate type F screw as a
makeshift thread tap.
Slowly tighten the screw one or two turns, then back it
compeltely out. This will remove any paint or debris in the
threaded hole without damanging the threads. Repeat the
process until the screw easily goes into the hole and the
thread looks clear.
Washers are recommended, but completely optional and
partially aesthetic. Please DO NOT use a washer on your
motherboard as this will most likely cause damage.
Type F Screw

Please visit our website for our current return policy, terms of
service, privacy policy, and other important information.
www.yuelbeast.com
[email protected]
© Yuel Beast Designs, 2022
Calypso User guide Version 8
Updated 11/2/22