Z-SHADE 10ft. Octagon Cantilever Patio Umbrella User manual

USER MANUAL
10ft. Octagon Cantilever
Patio Umbrella
©2020 Z-Shade Co. Ltd. All Rights Reserved. 91820
• Close and store the umbrella in windy conditions or when a storm approaches.
Never allow the umbrella to flap in the wind; this could damage the canopy. If damage occurs, this is not covered
by the warranty.
• Do not leave open umbrella unattended. If damage occurs, this is not covered by the warranty.
• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the umbrella. This is important to
prevent injury or material damage.
• When not in use, close and cover umbrella with a
protective cover (not included).
• Allow a wet canopy to dry while in open position,
but do not leave unattended.
• If necessary, clean the fabric with lukewarm water,
mild detergent, and a sponge.
• Wipe sliding marks on the aluminum poles with a
damp cloth.
Winter Storage:
• Store in a dry place.
After the Winter:
• Check the condition and function of the umbrella.
Z-Shade Co. Ltd.
(855) 4 Z-SHADE
[phone]
www.zshadeusa.com
SAFETY PRECAUTIONS
CARE AND MAINTENANCE
WARRANTY
Guarantee:
Z-Shade Co., Ltd. products being used in residential use and
applications only are guaranteed to be free from defects in original
material and workmanship.
Note: Z-Shade Co., Ltd. items are not warranted for commercial
applications.
Limited Warranty (Frames and Accessories): One (1) year
Includes: Frame, ribs, finial, tilt, cord, crank handle, housing,
canopy, and rib pocket seams. If a defect in the original material or
workmanship appears during the warranty period on any Z-Shade
product; Z-Shade Co., Ltd., at its option will replace the product or
parts without charge. Warranty Claim’s must be faxed or emailed in
(Claims over the phone will not be accepted.); please FAX your claim
to (951)-779-8990
Attn.: Customer Service or email to: [e-mail]
Fabric Limited Warranty:
The following fabrics have a limited warranty against fading for:
3 months - Polyester
The Limited Warranty only applies to Z-Shade product purchased
directly from Z-Shade or an authorized Z-Shade retail Dealer, as
defined in our Terms and Conditions; the Limited Warranty is not
transferable. Should the Purchaser or Owner sell the Z-Shade product
to another party, the warranty will not transfer to the new owner.
What Is NOT Covered:
Failure caused by unreasonable or abusive use, or failure caused by
neglect of reasonable and necessary care are not covered by this
warranty. Additionally, acts of nature (including but not limited to wind,
hurricanes, tornadoes, and storms) are not covered by this warranty.
This warranty covers return freight of any warranted product only for the
first year. This warranty gives you specific legal rights and you may have
other rights which vary from state to state. Closeout and promotional
items sold by the dealer as is are not covered by this warranty.
Wind Damage:
Z-Shade highly recommends that no umbrella, regardless of size
or weight, ever be left unattended in the open position. In windy
conditions, it is further recommended that umbrellas be closed,
removed from their base, and stored, or laid horizontally. This will
reduce the risk of damage to your umbrella, furniture, and other
belongings or property. To ensure stability of your umbrella, please
observe proper placement, and use sufficient weight (base).
Irregularities in Production Process:
The possibility of “Irregularities” in the product surface may occur
during the production process. However, these irregularities do not
reduce the quality of the product. Z-Shade monitors every stage of
production to ensure a clean and consistent appearance on every part.
Rust:
Rust is a natural part of the aging process of all Steel or Iron based
materials and is therefore NOT considered a defect. Z-Shade bases
are designed to require minimum maintenance. Bases should be kept
clean. Do not let dirt build up on the bases. Cleaning with mild soap
and water, and seasonal touch-up of any scratches, chips or occasional
rust seepage from crevices or hidden, un-finishable surfaces inherent
in some designs is all that is required. Never leave bases standing in
water. To keep your bases looking their best, you may wish to store
them when not in use for an extended period of time.
Seaside and Indoor Pool Usage:
CAUTION: Seaside and inside pool use, salt & chlorides can
accumulate on the powder coat finish, leading to finish failure. Failure
or neglect to make needed cleanings may cause paint to blister, and
such failure will void limited warranty.
This warranty is provided in lieu of all other warranties, expressed or implied.

CHECKLIST
A
SSEMBLE FRAME TO C ROSS BARS
1
A
SSEMBLE RESIN BASE WEIGHTS
2
OPENING & TILT ING UMBRELLA
3
ROTATING UMBRELLA
4
CLOSING UMBRELLA
5
A
E
D
F
B
A B
C
Screws (4)
Washers (4)
Allen
Wrench (1)
A - Canopy
B - Frame
C - Slider Handle
D - Rotation Knob
E - Cross Bars (2)
F - Resin Base Weight Containers (4)
Thank you for your purchase of Z-Shade’s AG5C Cantilever Umbrella.
Please remove all contents from the package, inspect and review checklist.
CAUTION: To reduce personal injury and damage to your AG5C, read and follow this assembly and operation guide.
We recommend a two-person team for assembly and disassembly. Save this information for future reference.
STEP 1 - Assemble the cross bar stand
by connecting both sections in a cross
(Fig. 1). Attach the frame to the cross bar
stand using the four (4) screws and
washers provided (Fig. 2). Use allen
wrench (provided) to secure frame.
IMPORTANT: Cross bar stand will not
support umbrella without proper weights.
Using the stand without weights will
damage your umbrella.
Resin Base Weight Containers
Cross Bar Stand will not support umbrella without proper weight. Using
the cross bar stand without weight will damage your umbrella and may
cause injury.
DO NOT OPEN UMBRELLA UNTIL WEIGHTS ARE SECURED.
• Prior to assembly it is important to decide on the location of the
umbrella.
• Allow ample height to avoid damage to your umbrella during assembly
and usage.
• Choose a location that is level and sturdy.
• Avoid any sloping or soft ground.
STEP 2 - Remove 4 resin base weights from packaging and lay on soft
surface (Fig. 3).
• Remove caps from each resin base weight by turning counter clockwise
(Fig. 4) to fill with all-purpose sand (Fig. 5).
• Remove/clean any excess sand from base weight cap and threads.
Secure cap on all filled containers by turning cap clockwise.
Next, begin to place each resin base weight onto Cross Bar Stand (Fig. 6).
Hook each section together so the resin base weights are secured in place
(Fig. 7). Begin with middle sections first and work your way out (Fig. 8).
Note: Each resin base weight holds up to 55 lbs. of sand, 220 lbs. for all 4.
(Fig. 3)
(Fig. 1) (Fig. 2)
(Fig. 6) (Fig. 7)
(Fig. 8)
(Fig. 9)
(Fig. 10)
(Fig. 11)(Fig. 12)
(Fi
g
. 12)
(Fig. 4) (Fig. 5)
NOTE: Two persons may be
needed for the following action.
STEP 3 - Before opening the umbrella, release the fabric band and allow the umbrella to unfurl.
There are 4 holes on the frame, when you open the umbrella, raise the slider handle to the third (3) hole (counted from the bottom), then
release the slider handle. Slowly turn the crank handle in a clockwise direction until the canopy is fully opened (Fig. 9), then you can raise the
slide handle to the highest hole setting (Fig. 10); if the canopy does not begin to open, check that the umbrella ribs are not tangled.
DO NOT FORCE THE CRANK HANDLE. Now the umbrella is ready to use.
STEP 4 - The umbrella will rotate 360° by pulling out the rotation knob and turning the knob 180 ° (Fig. 11), reset the rotation knob when
the umbrella is at your desired orientation (Fig. 12).
STEP 5 - To close the umbrella, begin by turning the crank handle counter-clockwise (Fig. 12) while simultaneously lowering
the slider handle until the canopy is fully closed. Use the fabric band to secure the umbrella frame to side pole.