ZACHVO ZA-WPH-1 User manual

ZACHVO®
INSTRUCTION MANUAL
Model no.: ZA-WPH-1
110-120V 1500W
E-Mail:[email protected]
ASSEMBLE & OPERATION INSTRUCTION
Please read carefully and Save this instruction for future reference

Introduction
The infrared heater contains an gold halogen lamp formed reflector heating system that provides even heat distribution.
The infrared heater saves 30%-40% of electricity in comparison to traditional heaters. The infrared heater is commonly used for indoor or
outdoor spot heating. Perfect for garages, outdoor patios, indoor pools or workshops.
Warning
READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation, maintenance and operation of the
heater can be dangerous. Observing the following procedures will reduce the risk of fire, electric shock, injury to person and keep
installation time to a minimums. Save these instructions for future used.
1. Read all instruction before using this heater.
2. Remove the unit form it’s packaging and check to make sureit is in good condition before using.
3. Do not let children play with parts of package (such as plasticbags)
4.Check the household voltage to ensure it matches the heater’s rated specification.
5.Check the power cord and plug carefully before used, to make sure that they are notdamaged
6.Before unplugging the power cord, be sure to turn off the power, when energizing the unit, be sure your hands are day to
prevent form electric shock.
7.Do not use flammable objects near or point the heater like furniture, pillows. Bedding, paper, cloths and curtains at least 3 feet
( 1meter ) form the front of the heater and keep them always the sides and rear.
8. Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid
9. To protect against electric shock, do not immerse cord or plug in water or any otherliquid.
10.Do not insert or allow foreign objects to enter any ventilation or exhaust opening , as this may cause an electric shock, fire or
damage to the heater.
11. Always unplug the heater when not in use.
12. Do not allow cord to overhang the counter top where it can be easily pulled bychildren.
13. Do not put fingers or foreign objects into the grill while in operation .
14. Do not leave the appliance unattended when in use.
15. This heater is not intended for use in bathrooms, laundry and similar indoor locations, never located heater where it may fall
into a bathtub or other water container.
16. No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or
mishandling.
17. This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities or
lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children ad vulnerable people should be supervised to ensure they do not play with the
appliance.
18. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
19. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage.
Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation.
20. Parts of the heater may exceed 200℃, Contact with the heating tube, reflector, or metal parts near the heating tube, may
cause severe BURNS . To avoid burns, do not let bare skin touch hotsurface.
21.ALWAYS allow heating element to cool at least 10 minutes before touching the heating tube or adjacent part
22.This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local
municipality for the nearest collection point.

WARNING : NEVER place hands under the heating elements.
Introduction
The halogen heater produce instant and comfortable heat like the sun. These robust and weatherproof heaters are
designed for domestic and commercial heating applications within outdoor areas, it is for outdoor use only.
Model
ZA-WPH-1
Voltage(V)
110-120V AC
Wattage(W)
1500W
Hertz(Hz)
60
Dimensions W×H×D(inches)
20.02*4.13*2.83 inches
Weight(lbs)
3.7 lbs
This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 68.1. An adapter as shown at C is
available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending
from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter
should not be used if a three-slot grounded receptacle is available.

ASSEMBLY INSTRUCTIONS

Tools Needed:
* Pencil *Hammer *Level *Screw Driver *Power Drill and drill bits
A wall mounting bracket is provide with the heater which has been specifically designed to allow this product to be fitted to a wall or ceiling
before drilling the holders for the wall/ceiling is solid and that there are no hidden water pipes or electric wires.The heater must be installed
no less than 16’’ form side walls and no less than 6”’ off the floor.
Important: Ensure that the supply cables is well mounted and that it does not come into contact with reflector of the heater or that is does
not trail into heated area, the supply cable can be fixed to them metal mounting bracket behind heater with plastic zip ties

The heater must be installed at least 1.8 m above the floor

REMOTE CONTROL INSTRUCTION
OPERATING
Product Key Function:
1. Turn ON/OFF the power
2. Press key function: press the button, then press the heat levels (L1-L2-standby - off)
Noted: All SUNDEAR heaters and their remote controls have the same frequency, so it is possible to
control several heaters with just one remote.
PUSH BUTTON: on the right of heater, it could be manual operated without remote control.
Inserting Batteries (not included)
Insert 2 AAA/ Alkaline type batteries into your remote control
1. Flip the backside of your remote control and pull out battery cover. Insert the batteries in accordance
with the instructions and polarity the batteries.
2. Change the batteries in the same way depicted above.
FUNCTION & OPERATION
1. PLUG the unit into a plug socket, make sure the power supply is the same as rated
2. PRESS the power button on the right side of heater
3. TURN ON the heater by remote control, or off the heater
4. DOWN & UP BUTTON, setting the power level
CLEANING AND MAINTENANCE
Regular and careful cleaning helps your infrared heater operate efficiently for many trouble free years. To clean your heater
follow steps below
Unplug the power cord for your safety before cleaning your appliance.
1. Make sure the heater is cool before continuing
2. To keep the heater clean, the outer shell maybe cleaned with a soft, damp cloth. You may use a mild detergent if necessary.
After cleaning, dry the unit with a soft cloth. (CAUTION: DO NOT let liquids enter the heater)
3. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage
or deterioration to the surface of the heater.
4. DO NOT immerse the heater in water
5. Wait until the heater is completely dry before use.
Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build up. Use packaging carton to store.
Remote Control Function
Button
Function (Heater On)
Function (Heater Off)
LEDDisplayon
Heater
O
Turns heater on or off
I
Power setting
Turns heater on to
Level1(50%*power)
II
Power setting
Turns heater on to
Level 2 (100%*power)

Troubleshooting
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the main fuse is working
3.Light display, but no heat: Bulb is damaged. Arrange for replacement bulb with local Dealer