Zanussi ZPB 1260 User manual

BUILT-IN OVEN
ZPB 1260
INSTRUCTION BOOKLET

2
ENGLISH
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italy)
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
Important Safety Information
During use
• Duringusetheappliancebecomeshot.Careshouldbe
taken to avoid touching heating elements inside the
oven.
• This appliance has been designed for cooking edible
foodstuff only and must not be used for any other
purposes.
• Ensure that all control knobs are in the OFF position
when not in use.
• Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables are
notincontactwithit and keep themfarenoughfromthe
heated parts of this appliance.
•If the appliance is out of order, disconnect it from the
electric supply.
•Donotleaveuntensilscontainingfoodstuffs,e.g.fat,oil
oranyinflammableproduct in or ontheappliance.This
could cause damage in case the appliance is
inadvertentlyswitchedon.
• Always place the dripping pan in position to collect fat
when using the grill or when cooking meat. Pour a little
water into the dripping pan to avoid smoke and
unpleasant smells.
• Alwaysuseovenglovestoremovepansfromtheoven.
• Forhygieneand safety reasons,this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
• Disconnect the appliance from the electrical supply,
beforecarryingoutanycleaning or manteinance work.
•Some parts of the appliance are covered by a shock-
proof plastic film. Remove this film before using the
oven.
•Always stand back from the oven when opening
the oven door during cooking or at the end of it to
allow any build up of steam or heat to release.
• Never use steam or steam machines to clean the
appliance.
• We recommend that you supervise each step of the
pyrolytic cleaning cycle. A power failure could cause a
temperatureincreaseofthe surround orcabinetwhich
could result in a fire.
It is important that the oven door, the door gasket, the
oven light and the cavity are in good condition to avoid
a fire.
Abuild-upoffat or other foodstuffcouldgenerate white
smoke, irritating for your eyes and the respiratory
system. We recommend that you stop the cleaning
cycle using the ON/OFF button to cool down the oven
cavity. Do not disconnect the appliance from the
electric supply. When the oven has cooled down
remove the food residue with a wet sponge.
• The manufacturer disclaims any responsability
should all the safety measures not be carried out.
Child Safety
• This appliance has been designed to be operated by
adultsandchildren under supervision.Youngchildren
must not be allowed to tamper with the controls or
play near or with the oven.
• Accessible parts of this appliance may become hot
when it is in use. Children should be kept away until
it has cooled.
Installation
• It is mandatory that all operations required for the
installationare carriedout by a qualified or competent
person, in accordance with existing rules and
regulations.
• It is dangerous to alter the specification in any way.
• Once you have removed all packaging from the
appliance, ensure that it is not damaged and the
electriccableisinperfectcondition.Otherwise,contact
your dealer before proceeding with the installation.
Service
• Underno circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
• After installation, please dispose of the packaging
with due regard to safety and the environment.
• Whendisposingofan old appliance, makeitunusable,
by cutting off the cable. Remove any door catches,
to prevent small children being trapped inside.

3
Contents
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683
(LowVoltageDirective);
* 93/68 (GeneralDirectives);
* 89/336 (Electromagnetical
Compatibility Directive) .
andsubsequent modifications
Guide to use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental Information
))
))
)
It is most important that this instruction book
should be retained with the appliance for
future reference. Should the appliance be
sold or transferred, always ensure that the
book is left with the appliance in order that the
new owner can get to know the functions of
the appliance and the relevant warnings.
For the User
Important Safety Information 2
Description of the Oven 4
Control Panel 5
When the Oven is First Installed 6
Before the First Use of the Oven 6
Using the Oven 7
Programming the Oven 8
Safety and Energy Saving Functions 10
Hints and Tips 12
Cooking Tables 13
Cleaning the Oven 15
Pyrolitic Cleaning 15
Replacing the Oven Light 17
Cleaning the Oven Door 18
Something not Working 20
Service and Spare Parts 20
Customer Care Department 21
Guarantee Conditions 21
For the Installer
Installation 22
Technical Data 22
Electrical Connection 22
Building In 23

4
Description of the Oven
OvenLight
Grill Element
Fan
Rating
Plate
Control
Panel
Oven accessories
Oven shelf (x 2)
Removable
handle
Grill / Roasting pan
Grill Pan Grid

5
Control Panel
Push Buttons
1. - ON / OFF
2. - Cooking Functions Control
3. - Fast Heat Up Function
4. - Pyrolitic Function
5. - Decreasing Control (Time or Temperature)
6. - Increasing Control (Time or Temperature)
7. - Time Function
"On/Off" Push Button
The oven must be switched on before setting any cooking
function or programme. When button is pressed, the
oven symbol will come on the display and the oven light
will switch on (Fig. 1).
To switch off the oven, you can press button at any
time. Any cooking function or programme will stop, the
oven light will switch off and the time display will show
the time of day only.
All the oven functions are controlled by an electronic
programmer.
You can select any combination of cooking function,
cooking temperature and automatic timing.
In the event of a power failure, the programmer will
keep all the settings (time of day, programme
setting or programme in operation) for about 3
minutes. If power is not restored within 3 minutes,
all the settings will be cancelled. When the power
is restored, the numbers in the display will flash,
and the clock/timer has to be reset.
Special functions
The following functions can be activated by pressing two
buttons at the same time:
- Child lock: press button and button “ “.
- Beep on touch: press button and button “ “.
- Demo mode: press button
B
and button “ “.
For further details, see chapter “Safety and Energy Sav-
ing functions”.
CookingFunctions
display
Time
display
Temperature
display
12 34 5 67
Fig. 1
Cooling fan
The cooling fan operates during cooking. Air is expelled
through vents between the oven door and the control panel,
as shown in the diagram.
The cooling fan may run on after the oven is switched off
to keep the controls cool. This is quite normal.
The Safety Thermostat
This oven is provided with a safety thermostat. In case of
malfunctioning of the main thermostat, and consequent
over-heating, the safety device will stop the power supply
to the appliance. If this happens, call your local Service
Force Centre. Under no circumstances should you
attempt to repair the appliance yourself.

6
To set the correct time of day :
1. press timefunction button and, while the symbol
is flashing, set the correct time of day by
pressing buttons “ “ or “ “ (Fig. 2) .
The time arrow symbol will disappear about 5
seconds after the correct time is displayed.
2. if the symbol is not flashing anymore, press time
function button twice.
Then, proceed as described in point 1.
It is possible to set the time of day only when
the oven is off.
When the oven is first connected to the electrical
supply, the display will automatically show 12:00 and
the symbol will flash.
Ensure the correct time of day is set before using the
oven.
Before the First Use of the Oven
Remove all packaging, both inside and outside
the oven, before using the oven.
The oven will work only if the time of day has
been set.
Before first use, the oven should be heated without
food.
During this time, an unpleasant odour may be
emitted. This is absolutely normal, and is
caused by residues of manufacturing.
1. set the time of day with the electronic programmer
(see paragraph "To set the correct time of day").
2. press button to switch on the oven.
3. press button twice and select the "Conventional
Cooking" function (Fig. 3).
4. set the temperature to 250°C using the increasing
push button “ “.
5. Allow the oven to run empty for approximately 45
minutes.
6. open a window for ventilation.
This procedure should be repeated with the "Full Grill"
function for approximately 5-10 minutes.
Once this operation is carried out, let the oven
cool down, then clean the oven cavity with a
soft cloth soaked in warm water to which a little
mild washing-up liquid has been added.
Before cooking for the first time, carefully wash
the oven accessories.
To open the oven door, always hold the
handle in the centre (Fig. 4).
Fig. 2
Fig. 3
Fig. 4
When the oven is first installed

7
How to select a Cooking
Function
1. Switch on the oven by pressing the button.
2. Press button to select the required oven function.
Each time button is pressed, a cooking symbol
will appear in the display and the corresponding
cooking function number will appear to the left of the
currently selected cooking function symbol (Fig. 6).
3. If the pre-set temperature is not suitable, press button
“ “ or “ “ to adjust the temperature in 5 degree
steps.
- as soon as the oven heats up, the thermometer
symbol rises slowly , indicating the degree to which
the oven is currently heated;
When the required temperature is reached, an
acoustic alarm will sound for a short time and the
thermometer symbol will light permanently.
How to set the temperature and
cooking time
1. Press button “ “ and “ “ to increase or decrease
the pre-set temperature while the “°” symbol is flashing
(Fig. 7).
2. Press button “ “ and “ “ to increase or decrease
the pre-set cooking time while the symbol is
flashing.
Fig. 7
Fig. 6
Shelf Positions
The oven shelves can be placed at different heights to
obtain better cooking results.
The levels are shown in Fig. 5.
Using the Oven
4
3
2
1
• Always use oven gloves to remove and replace food
in the oven.
• Always ensure that you are using oven proof baking
trays, oven dishes, etc.
• Do not place baking trays, cake tins or aluminium foil
directly on the base of the oven. This could cause a
heatbuild-upwhichcouldaffecttheperformanceofthe
ovenand damage the oven enamel.
• Carefully supervise cooking with fat or oil, since
these types of foodstuff can result in a fire, if over-
heated.For the samereason, be carefulwhen placing
orremoving food in the oven, not to let anyfat or oil fall
on the oven base. If this happens, carefully clean the
oven to avoid unpleasant smells or smoke.
Always cook with the oven door
closed.
Fig. 5

8
Fan cooking - This setting allows you to roast
or roast and bake simultaneously using any
shelf, without flavour transference. Pre-set
temperature:175 °C.
Conventional cooking - The heat comes
fromboththetopandbottomelement, ensuring
even heating inside the oven. Pre-set
temperature: 200 °C. The maximum setting
temperature is 285 °C.
Full Grill - The full grill element will be on.
Recommended for large quantities. Pre-set
temperature:250 °C.
Grill - can be used for grilling small quantities.
Pre-set temperature: 250 °C.
Thermal Grilling - This function offers an
alternative method of cooking food items,
normallyassociated with conventional grilling.
The grill element and the oven fan operate
together, circulating hot air around the food.
Pre-settemperature: 180 °C.
Select a maximum temperature of 200 °C.
Pizza Oven - The bottom element provides
direct heat to the base of pizzas, quiches or
pies, while the fan ensures air is circulated to
cook the pizza toppings or pie fillings.
Pre-settemperature:175 °C.
Bottom heating element - The heat comes
from the bottom of the oven only, to allow you
to finishyour dishes.Pre-set temperature: 250
°C.
Top heating element - The heat comes from
the top of the oven only, to allow to you finish
your dishes. Pre-set temperature: 250 °C.
Defrosting – The oven fan operates without
heat and circulates the air, at room temperature,
inside the oven. This function is particularly
suitable for defrosting delicate food which could
be damaged by heat, e.g. cream filled gateaux,
iced cakes, pastries, bread and other yeast
products.
Pyrolytic cleaning - This function allows you
to clean thoroughly the oven cavity.
Programming the Oven
How to set the minute minder
1. Press time function button to select the Minute
Minder Function. The relevant symbol will flash and
the control panel will display "0.00" (Fig. 8).
2. Press button “ “ to select the required time. Maximum
time is 23 hours 59 minutes.After the setting is carried
out, the Minute Minder will wait 3 seconds and then
start running.
3. When the programmed time has elapsed, an acoustic
alarm will be heard.
4. To switch off the acoustic alarm, press any button.
The oven will NOT switch off if in use.
The Minute Minder function can also be used
when the oven is off.
To use or to change the Minute Minder setting:
press time function button until the symbols and
flash.
It is now possible to change the Minute Minder setting by
pressing button “ “ or “ “.
To cancel the Minute Minder:
press time function button until the symbols and
flash.
Press button “ “ to decrease the time until "0.00" shows
in the display (Fig. 9).
The following list displays in sequence all the cooking
functionsavailable.
1
2
3
4
5
6
7
8
9
10
Cooking Functions
Fig. 8
Fig. 9

9
To programme the Oven to switch
on and off
1. Carry out the "Cooking Duration" setting as
described in the relevant chapter.
2. Press time function button until the "End of
Cooking" function is selected and the relevant
symbol flashes. The control panel will display the
end of cooking time (that is, the actual time +
cooking duration time) (Fig. 13).
3. Press button “ “ to select the required end of
cooking time.
4. After the setting is carried out, the programmer will
wait 3 seconds and then start running.
5. The oven will switch on and off automatically. The
end of cooking will be marked by an acoustic alarm.
6. To switch off the acoustic alarm, press any button.
To cancel the programme, simply cancel the
Cooking Duration Time.
To programme the Oven to
switch off
1. Switch the oven on, place food in the oven, select
a cooking function and adjust the cooking tempe-
rature, if required.
2. Press time function button to select the
"Cooking Duration" function. The "Cooking Duration"
symbol will flash and the control panel will
display "0.00" (Fig. 10).
3. While the symbol is flashing, press button “ “
to select the required time. Maximum time is 23
hours 59 minutes. The programmer will wait 3
seconds and then start running.
4. When cooking time is over, the oven will be switched
off automatically and an acoustic alarm will be heard
while the control panel will display "0.00".
5. To switch off the acoustic alarm, press button .
If you press any other button the alarm will stop
(Fig. 11). Then, you need to reset the programmer
display by pressing button .
The control panel will display the time of day and the
Cooking Duration symbol will go out.
To cancel the Cooking Duration Time:
— press time function button until the symbol
flashes.
— press button “ “ to decrease the time until the
display shows "0.00" (Fig. 12).
Fig. 10
Fig. 12
Fig. 11
Fig. 13

10
"Fast Heat Up" function (Booster)
After a cooking function has been selected and the
temperature has been adjusted, the cavity will gradually
heat up until the selected temperature is reached. This
will take from 10 to 15 minutes, depending on selected
function and temperature.
If it is necessary to reach the required temperature in a
shorter time, the fast heat up function can be used.
1. Switch the oven on by pressing button .
2. Set the required cooking function and temperature as
explained in the previous pages.
3. Set the temperature by pressing button “ “ or “ “.
The temperature will appear in the display.
4. Press button . The temperature display will show
"FHU" (Fig. 16).
5. Press button and the symbol “°” will flash for
approximately 10 seconds. Now it is possible to
select the required temperature by pressing button
“ “ or “ “.
6. When the required temperature is reached, an acoustic
alarm will sound for a short time, and the temperature
display will revert to the set temperature.
This function can be used with any cooking function or
temperature.
Safety and Energy Saving Functions
Safety Cut-Off Function
The oven will switch off automatically if any change of
setting is made, according to the table below (Fig. 14).
If temperature setting is: the oven will switch off:
250°C after 1 1/2hours
from 200 up to 245°C after 5,5 hours
from 120 up to 195°C after 8,5 hours
less than 120°C after 12 hours
Fig. 14
Fig. 15
Fig. 16
Child Safety Function
To avoid children switching on the oven, it is possible
to lock the oven controls.
1. Turn off the oven by pressing button .
2. Press buttons and “ “ at the same time and
keep them pressed for about 3 seconds. An
acoustic signal will be emitted and the indication
‘SAFE’ will appear in the display (Fig. 15).
3. The oven is now locked. Neither oven functions
nor temperatures can be selected.
To unlock the oven:
Press buttons and “ “ at the same time and keep
them pressed for about 3 seconds. An acoustic signal
will be emitted and the indication ‘SAFE’ will go off.
The oven can now be operated.
Residual Heat Function
When a Cooking Duration time is set, the oven will
automatically switch off a few minutes before the end of
the programmed time, and use the residual heat to finish
your dishes without energy consumption. All current
settings will be displayed until the Cooking Duration time
is over.
This function will not operate when the Cooking Duration
time is less than 15 minutes.

11
Error code
The electronic programmer does a continuous diag-
nostic check of the system. If some parameters are
not correct, the control unit will stop the activated func-
tions and the corresponding error code (letter “E” fol-
lowed by number digits) will be displayed.
For further details, refer to chapter “Something not
working” on page 20.
Demo mode
This mode is intended to be used in the shops to dem-
onstrate the oven functionality without any power con-
sumption except the oven lamp. To activate this func-
tion the appliance should be in stand-by mode.
— Press button and “ “ for approximately 2 sec-
onds (Fig. 17). An acoustic alarm will sound for a
short time .
— Press button and the “ id ” indication will appear
in the display.
All oven functions can be selected.
The thermometer symbol will not flash anymore and
“ id ” indication will be replaced by number digits.
Follow the above described procedure to disable
the demo mode.
Fig. 17

12
Hints and Tips on Cooking Fish
and Meat
Youcanplacemeat in ovenproofdishes, or directly onthe
oven shelf. In this case, remember to place the drip tray
in the first position from the bottom with some water in it.
Thedripping pan will avoid the falling of melted fat on the
ovenbase.
White meat, poultry and fish in general, need to be
cooked at a medium temperature (between 150 and 175
°C).If you need to cook redmeat (slightlybrowned on the
outside and more gently cooked in the inside), a higher
temperature(between 200 and 250 °C) for ashort time is
recommended.
Hints and Tips on baking
Cakes usually need to be cooked at a medium tempera-
ture (between 150 and 200 °C).
A short oven pre-heating (about 10 minutes) is
recommeded when cooking cakes or baking. Once the
cooking has been started, keep the oven door closed
duringall the cooking time, and check thecooking results
through the oven door glass.
When food is heated, it produces steam in the
same way as a boiling kettle does. When
steam comes in contact of the oven door
glass, it will condense and produce water
droplets.
To reduce condensation, ensure the oven is
well heated before placing food in the oven
cavity. A short oven pre-heating (about 10
minutes) will then be necessary before any
cooking.
We recommend you to wipe away
condensation after each use of the appliance.
Hints and Tips
Always cook with the oven door closed.
The oven is supplied with an exclusive system which
produces a natural circulation of air and the constant
recycling of steam. This system makes it possible to
cook in a steamy environment and keep the dishes soft
inside and crusty outside. Moreover, the cooking time
and energy consumption are reduced to a minimum.
During cooking steam may be produced which can be
released when opening the oven door. This is absolutely
normal.
However, always stand back from the oven
when opening the oven door during cooking
or at the end of it to allow any build up of
steam or heat to release.
Hints and Tips on grilling
If you need to grill meat or fish, place them directly on the
shelf after spreading a little oil on them.
Inthe grill function,heat comes onlyfrom the topelement.
Therefore,youneedtoadjustthecookinglevel depending
on meat or fish's thickness.
Always remember to place the dripping pan in the lower
position with some water in it.
When using the Thermal Grill Function, select
a maximum temperature of 200°C
Warning! - Do not place objects on the bottom of
the oven and do not cover it with aluminium foil
while cooking, as you can damage the enamelled
surfaces and the food you are cooking.
Always place pans, heat-resisting pans and
aluminium foils on the oven shelves.
Warning! - Be careful when you insert and extract
the grid and the drip tray from the oven in order
not to damage the enamelled surfaces of the oven
cavity.
Cooking times
Cooking times vary according to the type of food to be
cooked, its consistency, and volume.We suggest that
you take particular note of your first cooking experiments
with the oven, since operating in the same conditions for
the same dishes you will of course obtain similar results.
Only experience will enable you to make the appropriate
changes to values given on charts.

13
CAKES
Whisked recipes 2 170 2 160 45 ~ 60 In cake mould on the shelf
Shortbread dough 2 170 2 (1 and 3)* 160 20 ~ 30 In cake mould on the shelf
Butter-milk cheese cake 1 160 2 150 60 ~ 80 In cake mould on the shelf
Apple cake 1 180 2 (1 and 3)* 170 40 ~ 60 In cake mould on the shelf
Strudel 2 175 2 150 60 ~ 80 In cake tin on the shelf
Jam-tart 2 175 2 (1 and 3)* 160 30 ~ 40 In cake mould on the shelf
Fruit cake 1 175 1 160 45 ~ 60 In cake mould
Sponge cake 1 175 2 160 30 ~ 40 In cake mould on the shelf
Christmas cake 1 170 1 160 40 ~ 60 In cake mould on the shelf
Plum cake 1 170 1 160 50 ~ 60 In cake mould on the shelf
PASTRIES
Small cakes 2 170 2 (1 and 3)* 160 25 ~ 35 In baking tray
Biscuits 3 190 3 170 15 ~ 25 In baking tray
Meringues 2 100 2 100 90 ~ 120 In baking tray
Buns 2 190 2 180 12 ~ 20 In baking tray
Pastry: Choux 2 200 2 (1 and 3)* 190 15 ~ 25 In baking tray
BREAD AND PIZZA
1000 White bread 1 190 2 180 40 ~ 60 2 pieces in baking tray
500 Rye bread 1 190 1 180 30 ~ 45 In bread pan on the grid
500 Bread rolls 2 200 2 175 20 ~ 35 6-8 rolls in baking tray
250 Pizza 1 200 2 (1 and 3)* 190 15 ~ 30 On baking tray on the grid
FLANS
Pasta flan 2 200 2 (1 and 3)* 175 40 ~ 50 In mould on the shelf
Vegetable flan 2 200 2 (1 and 3)* 175 45 ~ 60 In mould on the shelf
Quiches 1 200 2 (1 and 3)* 180 35 ~ 45 In mould on the shelf
Lasagne 2 180 2 160 45 ~ 65 In mould on the shelf
Cannelloni 2 200 2 175 40 ~ 55 In mould on the shelf
MEAT
1000 Beef 2 190 2 175 50 ~ 70 On shelf and dripping pan
1200 Pork 2 180 2 175 100 ~ 130 On shelf and dripping pan
1000 Veal 2 190 2 175 90 ~ 120 On shelf and dripping pan
1500 English roast beef
1500 rare 2 210 2 200 50 ~ 60 On grid and dripping pan
1500 medium 2 210 2 200 60 ~ 70 On grid and dripping pan
1500 well done 2 210 2 200 70 ~ 80 On grid and dripping pan
2000 Shoulder of pork 2 180 2 170 120 ~ 150 With rind-in dripping pan
1200 Shin of pork 2 180 2 160 100 ~ 120 2 pieces-in dripping pan
1200 Lamb 2 190 2 175 110 ~ 130 Leg-in dripping pan
1000 Chicken 2 190 2 175 60 ~ 80 Whole-in dripping pan
4000 Turkey 2 180 2 160 210 ~ 240 Whole-in dripping pan
1500 Duck 2 175 2 160 120 ~ 150 Whole-in dripping pan
3000 Goose 2 175 2 160 150 ~ 200 Whole-in dripping pan
1200 Rabbit 2 190 2 175 60 ~ 80 Cut in pieces
1500 Hare 2 190 2 175 150 ~ 200 Cut in pieces
800 Pheasant 2 190 2 175 90 ~ 120 Whole
FISH
1200 Trout/Sea bream 2 190 2 (1 and 3)* 175 30 ~ 40 3-4 fishes
1500 Tuna fish/Salmon 2 190 2 (1 and 3)* 175 25 ~ 35 4-6 fillets
Cooking Tables
Traditional Cooking
Weight (gr.)
TYPE OF DISH
Fan Oven
NOTES
Cooking
time
minutes
temp.
°C temp.
°C
Traditional cooking and fan ducted cooking
Cooking times do not include pre-heating time.
A short oven pre-heating (about 10 minutes) is necessary before any cooking.
(*) If you need to cook more than one dish at the same time, we recommend you to place them on the levels quoted between
brackets.
If you wish to cook more than one dish at the same time, we suggest that you change the cooking levels of your dishes during the
last 5-10 minutes in order to obtain a more uniform colour of your dishes.
Level
4
3
2
1
Level
4
3
2
1

14
700 Pizza, large 1 200 15 ~ 25 in baking tray
500 Pizza, small 1 200 10 ~ 20 in mould on the shelf
500 Flat cake 1 200 15 ~ 25 in baking tray
TYPE OF DISH Quantity Temperature Time in minutes
(gr.) °C lower upper
side side
Rolled joints (turkey) 1000 3 200 30 ~ 40 20 ~ 30
Chicken (cut in two) 1000 3 200 25 ~ 30 20 ~ 30
Chicken legs — 3 200 15 ~ 20 15 ~ 18
Quail 500 2 200 25 ~ 30 20 ~ 25
Vegetable gratin — 3 200 20 ~ 25 —
St. Jacques shells — 3 200 15 ~ 20 —
Mackerel — 3 200 15 ~ 20 10 ~ 15
Fish slices 800 3 200 12 ~ 15 8 ~ 10
Fillet steaks 4 800 3 250 12 ~ 15 12 ~ 14
Beef-steaks 4 600 3 250 10 ~ 12 6 ~ 8
Sausages 8 — 3 250 12 ~ 15 10 ~ 12
Pork chops 4 600 3 250 12 ~ 16 12 ~ 14
Chicken (cut in two) 2 1000 3 250 30 ~ 35 25 ~ 30
Kebabs 4 — 3 250 10 ~ 15 10 ~ 12
Chicken (breast) 4 400 3 250 12 ~ 15 12 ~ 14
Hamburger 6 600 3 250 10 ~ 15 8 ~ 10
Fish (fillets) 4 400 3 250 12 ~ 14 10 ~ 12
Sandwiches 4-6 — 3 250 3 ~ 7 —
Toast 4-6 — 3 250 2 ~ 4 2 ~ 3
Grilling -
Upper
side
°C
Temperature
Pieces Weight
Quantity Cooking time
(minutes)
Lower
side
TYPE OF DISH
Thermal grilling
The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the
temperatures to suit individual preferences and requirements.
Weight (gr.)
TYPE OF DISH
Cooking
time
minutes
NOTES
"Pizza" function
Level
4
3
2
1
When using the thermal grill cooking function, select a maximum temperature of 200°C.
Cooking times do not include pre-heating time.
A short oven pre-heating (about 10 minutes) is necessary before any cooking.
Level
4
3
2
1
°C
Temperature
Level
4
3
2
1

15
Before cleaning always allow the cooling fan to
cool the oven down before switching off at the
electricity supply.
This appliance cannot be cleaned with steam or
with a steam cleaning machine.
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing-up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
• Household detergent and bleaches
• Impregnated pads unsuitable for non-stick
saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily soiled
it is recommended that a cleaning product such as Hob
Brite is used. Do not use paint scrapers to remove
soilage.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not
observed the glass panel may shatter.
If the door glass panel becomes chipped or
has deep scratches, the glass will be weakened
and must be replaced to prevent the possibility
of the panel shattering. Contact your local
Service Force Centre who will be pleased to
advise further.
Cleaning the Oven
Oven Shelves
Tocleanthe oven shelves,soak in warmsoapy water and
remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
Pyrolytic cleaning
Theoven cavity is coated with a specialenamel resistant
to high temperatures.
During the pyrolytic cleaning operation, the temperature
insidethe oven can reach about500 °Cthus burning food
residuals.
Foryour security, during the pyrolityccleaning operation,
theoven door automatically locks when the temperature
inside the oven approaches about 300 °C.
Upon completion of the cleaning operation, the
oven door will be locked until the oven cavity has
cooled down.
The cooling fan operates during cooking until the oven
has cooled down. After cooking, it is advisable to remove
all the food residues with a wet sponge.
However, from time to time, it will be necessary to do a
morecompleteand thorough cleaning,usingthe pyrolytic
cleaning function. You can select two different levels of
pyrolytic cleaning depending on how dirty the oven is.
Ifthe oven cavityis not very dirty, werecommend that you
select the pyrolytic 1 function (P I) on the programmer
display.
It is advisable to wipe the oven over with a soft sponge
soakedin warm water after each pyrolytic cleaning cycle
is carried out.
If the oven cavity is very dirty, we advise you to select the
pyrolytic 2 function (P 2) on the programmer display.
During the pyrolytic cleaning function, it is not possible to
usethe oven for 2 hours when selecting the Pyr 1 function
and up to 2 1/2 hours when the Pyr 2 function is active.

16
How to use the pyrolytic cleaning
function
Before activating the pyrolytic cleaning function,
remove any excessive spillage and make sure
that the oven is empty. Do not leave anything
inside it (e.g. pans, grids, baking tray, dripping
pan, etc.) as this could heavily damage them.
Ensure that the oven door is closed before
activating the pyrolytic cleaning function.
When the pyrolytic cleaning function is on, it is
advisable not to use the hob as this could cause
overheating and damage the appliance.
During the pyrolytic cleaning cycle the oven door
becomes hot. Children should be kept away until
it has cooled.
Choose this function to clean the oven by pyrolysis.
The following pyro levels are available:
Pyrolytic 1 (P I) time : 2 h = 30 min heat-up +1 h at
480°C + 30 min cooling down.
Pyrolytic 2 (P 2) time : 2 h 30 min. = 30 min heat-up +1
h 30 min at 480°C + 30 min cooling down.
The pyro duration time cannot be changed.
To activate the pyrolytic cleaning function proceed as
follows:
1. Press button to switch on the oven. Press the
button as often as necessary, until the “Pyro“
function symbol (level 1 - P I) will appear on the
display (Fig. 18).
2. The Cooking Duration symbol will flash for 5
seconds; during this time push ' ' or ' ' buttons to
select the pyrolytic 1 (P I) or pyrolytic 2 (P 2) function
(Fig. 19).
3. Once you have chosen the desired pyrolytic function,
the “Pyro” writing will flash on the display waiting for
confirmation to start the pyro cleaning function . If
'' or ' ' buttons are pushed, the Cooking Duration
symbol will flash again to allow you to change
the pyro selection (P I or P 2) (Fig. 19).
4. To confirm which pyrolytic function you desire, press
button , the “Pyro” text will stop flashing and the
pyrolytic cleaning cycle starts (Fig. 20).
5. After some time, the door lock will be activated and
the related symbol will be displayed (Fig. 21). At
this time the button is no more active.
At the end of the pyrolitic cleaning process, the display
shows the time of day. The oven door is locked.
Once the oven has cooled down, an acoustic signal will
be emitted and the door will unlock.
To stop the pyrolytic cleaning cycle at any time, press
button .
NOTE: The time indication is comprehensive of the
cooling down time.
Fig. 18
Fig. 19
Fig. 20
Fig. 21
If you select a cooking function while the pyrolytic
function is active, the cleaning cycle will be inter-
rupted.
If the oven door lock is activated, it is impossible
to select any cooking function until the door lock
is off.

17
To programme the pyrolytic
cleaning cycle (delayed start,
automatic stop)
If you wish, you can programme the start and end time
of the pyrolytic cleaning cycle.
1. Press button to switch on the oven. Press the
button as often as necessary, until the “Pyro“
function symbol (level 1 - P I) appears in the
display.
2. The Cooking Duration symbol will flash for 5 sec-
onds; during this time push ' ' or ' ' button to se-
lect the pyrolytic 1 (P I) or pyrolytic 2 (P 2) function.
3. Once you have chosen the desired pyrolytic func-
tion, “Pyro” will flash in the display waiting for confir-
mation to start the pyro cleaning function.
At this time, push the time function button
(Fig. 22). The time indication will appear in the
dispaly, the "End of Cooking" symbol and
will flash on the display.
Push ' ' or ' ' buttons to select the required end of
cycle time. Once you have selected the ending time
of the pyrolytic cleaning cycle, press button to
activate the function.
4. After some time, the door lock will be activated and
the related symbol will be displayed.
At the end of the pyrolitic cleaning process, the display
shows the time of day. The oven door is locked.
Once the oven has cooled down, an acoustic signal will
be emitted and the door will unlock.
To stop the pyrolytic cleaning cycle at any time, press
button .
Fig. 22
Replacing the Oven Light (Fig. 25)
If the oven bulb needs replacing, it must comply with the
following specifications:
- Power: 40 W,
- Voltage: 230 V (50 Hz),
- Temperature Rating of 300 °C,
- Thread type: E14.
These bulbs are available from your local Service Force
Centre.
To replace the faulty bulb (Fig. 23):
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace with the new one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
Fig. 23
))
))
)

18
Cleaning The Oven Door
The oven door is made up of four glasses.
It is possible to remove them for easier cleaning.
Warning - The oven door may bang shut if you try
to extract the inner glasses when the oven door
is still fitted to the oven.
Before cleaning the oven door, we recommend you to
remove it from the oven.
Proceed as follows:
1. open the oven door completely and locate the two
hinges which link the door to the oven;
2. unlock and turn the small levers located on the two
hinges;
3. handle the door by its left- and right-hand sides,
then slowly turn it towards the oven until it is half-
closed;at this point, gently pull the ovendoor away
fromthe oven frame;
5. extract the inner glass support; 6. gentlyextract the three inner glasses, starting with
the uppermost one first.
4. placetheovendooron a solid surface,beingcareful
to avoid the glass becoming scratched. Then
remove the two screws located on the sides of the
ovendoor;

19
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not observed
the glass panels may shatter.
If the door glass panels become chipped or have
deep scratches, the glasses will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Force
Centre who will be pleased to advise further.
Clean the oven door glass with warm water and a softh
cloth only. Never use harsh abrasives as they could
damage the special heat-resistant surface of the inner
glasses.
Once the cleaning is carried out, refit the oven door,
followingthe procedurein reverse.
The two glasses in the middle are special glasses
that have been treated to resist heat. They are
marked with a small dot located on a corner and a
black frame respectively.
It is important that, when refitting the oven door,
the inner glasses are fixed in the right position.
To check if this operation has been carried out
correctly, when inserting the glass, make sure that
the surface of the glass marked with a black frame
looks downwards and that the dot is located on the
upper left corner of the glass (Fig 24). Fig. 24

20
Something not working
SYMPTOM
The oven does not come on.
The oven light does not come on.
It takes too long to finish the dishes, or they are
cooked too fast.
Steam and condensation settle on the food and the
oven cavity.
The timer does not work.
The oven fan is noisy.
Error code "E40" appears on the control panel.
An error code other than "E40" appears on the
control panel.
The display shows "12.00".
SOLUTION
Press the OVEN ON button, then select a cooking
function.
Check the fuse and ensure the socket switch or the
switch from the mains supply to the oven are ON.
Switch on the oven using push button .
Check the light bulb, and replace it if necessary (see
"Replacing the Oven Light")
The temperature may need adjusting
Refer to the cooking function sections and to any
cooking chart provided
Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
Check the instructions for the timer.
Check that shelves and bakeware are not vibrating in
contact with the oven back panel.
Switch the appliance off and leave it to cool down.
Push button ON / OFF to switch on the appliance.
Take note of the error code and contact an authorised
Service Centre.
Set the time of day (see chapter "How the set the time
of day").
If the appliance is not working correctly, please carry out the following checks, before contacting your local
Service Centre.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not Work-
ing.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date