Zeiss DTC-A User manual
16 17
EN SAFETY INSTRUCTIONS
• Please note the safety instructions of your
attachment.
• Before use, check that the attachment and the
adapter are securely tted on the riescope.
• If used with a riescope: Improper or inaccurate
mounting of the attachment and the adapter
on the riescope may result in a shift in the
point of impact, which may aect accuracy.
• The adapter must no longer be used if it shows
signs of damage.
• Ensure that there is a distance of at least 5mm
between the adapter and the gun barrel.
• Do not place the adapter in the hands of small
children. Incorrect handling can cause small
parts to come loose which may be swallowed.
EN ZEISS DTC-A & DTC-R |
Manual&Safety Instructions
EN MANUAL
Overview
AB
CE
DF
H
I
G
Components
A Thermal imaging attachment
B Retaining ring
C DTC-R M52
D Set screw
E Locking lever
F Locking screw
G Riescope
H DTC-A
I Shutter
18 19
Scope of supply
Product Order no. Scope of supply
DTC-A 48 528332 DTC-A
Hexagonal screw 2mm
Hexagonal screw 4mm
DTC-A 56 528333
DTC-A 62 528334
Preparation before mounting
Note: Tighten the set screw with a torque of max. 1.9Nm.
(2)
(1)
(3)
(5)
(4)
To connect your DTC-A with the riescope, slide
it onto the riescope(1) and close the locking
lever(2).
If the connection is too loose or too tight,
loosen the locking screw(3), adjust the set
screw accordingly(4), and retighten the locking
screw(5).
The locking lever is set properly if the mounted
adapter cannot be moved.
20 21
Mounting DTC-R M52 and DTC-A
(2)
(1)
(3)
To mount the DTC-R M52, turn the retaining
ring(1) clockwise as far as it will go. Place
the DTC-R M52 onto the thermal imaging
attachment(2) and turn it clockwise(3) until it
stops. Turn the marking of the DTC-R M52 back to
the position shown in the image. The DTC-R M52
can still be turned freely.
(2)
(1)
Plug the DTC-A and the DTC-R M52 together at
the marking(1) and turn the shutter(2) hand-tight
(approx. 20°) counterclockwise.
Turn the retaining ring counterclockwise as far as
it will go. Fix the retaining ring with one hand. Use
your free hand to grasp the connected DTC-R M52
and DTC-A and turn them as tightly as possible
clockwise towards the retaining ring.
22 23
(2)
(1)
To connect the thermal imaging attachment
including the adapter to the riescope, tilt the
locking lever(1) in the direction of the riescope
and attach the assembly to the riescope(2).
Make sure that the objects are aligned as shown.
(1)
Once the riescope and the thermal imaging
attachment are aligned, ip the locking lever(1).
Use the target line correction of the thermal
imaging attachment for ne-tuning.
Disassembly
For disassembly, carry out these steps in reverse
order.
24 25
Quick assembly
(1)
(2)
Customer Service and Warranty
For service questions or obtaining the
warranty terms, please see our website:
www.zeiss.com/cop/warranty
For service inquiries or a free copy of the warranty
terms for your region, please contact:
ZEISS Customer Service
Carl Zeiss Sports Optics GmbH
Gloelstr. 3–5
35576 Wetzlar, Germany
Phone +49 800 934 77 33
E-Mail [email protected]
ZEISS Customer Service USA
Carl Zeiss SBE, LLC
Consumer Products
1050 Worldwide Blvd.
Hebron, KY 41048-8632, USA
Phone +1-800-441-3005
E-Mail [email protected]
This manual suits for next models
1
Other Zeiss Adapter manuals
