Zennio Lumento DX4 Guide

© Zennio Avance y Tecnología S.L. Edition 6 Further information www.zennio.com Page 1/2
Lumento DX4
4-channel constant voltage PWM dimmer in DIN rail for DC LED loads with 6 binary/analogue inputs
ZDI-RGBDX4 TECHNICAL DOCUMENTATION
FEATURES
•4 constant voltage channels configurables (independent channels,
RGBW channels and RGB+W channels).
•6 analog/digital inputs.
•Master Light control.
•External 12-30VDC power supply.
•Manual output operation with push button and LED status indicator.
•Total data saving on KNX bus failure.
•Integrated KNX BCU.
•Dimensions 60 x 90 x 79mm (4,5 DIN units).
•DIN rail mounting (EN 50022), through pressure.
•Conformity with the CE directives (CE-mark on the right side).
Figure 1: Lumento DX4
Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe
mode. If this button is held for more than 3 seconds, the device enters the test mode.
Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode
is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it emits a red flash. A blue blink
represents an error.
GENERAL SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device
Electric operation control device
KNX supply
Voltage (typical)
29VDC SELV
Voltage range
21..31VDC
Maximum
consumption
Voltage
mA
mW
29VDC (typical)
6.5
188.5
24VDC¹
10
240
Connection type
Typical TP1 bus connector for 0.80mm Ø rigid cable
External power supply
12-30VDC
Operation temperature
0°C .. +55°C
Storage temperature
-20°C .. +55°C
Operation humidity
5 .. 95%
Storage humidity
5 .. 95%
Complementary characteristics
Class B
Protection class
III
Operation type
Continuous operation
Device action type
Type 1
Electrical stress period
Long
Degree of protection
IP20, clean environment
Installation
Independent device to be mounted inside electrical panels with DIN rail (EN
50022)
Minimum clearances
Not required
Response on KNX bus failure
Data saving according to parameterization
Response on KNX bus restart
Data recovery according to parameterization
Operation indicator
The programming LED indicates programming mode (red), test mode
(green) and error (blue blinking). Colour shift LEDs show the current colour.
Each output LED indicates its status.
Weight
184g
PCB CTI index
175V
Housing material
PC FR V0 halogen free
¹ Maximum consumption in the worst-case scenario (KNX Fan-In model)
3
10
7
9
2
8
1
5
4
6
6
1. External power supply
2. Colour shift status LED*
3. Colour shift control buttons*
4. Channel control button
5. Channel status LED
6. Output channels
7. KNX connector
8. Programming/Test LED
9. Programming/Test button
10. Inputs

© Zennio Avance y Tecnología S.L. Edition 6 Further information www.zennio.com Page 2/2
SAFETY INSTRUCTIONS
•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.
•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire
KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other
accessories, in case of being installed.
•The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10A mini-circuit-breaker is
recommended. To prevent accidents, it must remain open in case of manipulation of the device.
•Once the device is installed (in the panel or box), it must not be accessible from outside.
•Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material
while in use.
•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at
http://zennio.com/weee-regulation.
OUTPUTS SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of outputs
4
Output type
Solid state switching device
Maximum load per output
6A
Load type
LED strip (monochrome, RGB or
RGBW) with common anode (+)
Short-circuit protection
YES
Overload protection
YES
Overheating protection
YES
Connection method
Screw terminal block
Cable cross-section
0.5-4mm² (IEC) / 10-30AWG (UL)
EXTERNAL POWER SUPPLY SPECIFICATIONS AND
CONNECTIONS
CONCEPT
DESCRIPTION
Voltage
12-30VDC (voltage in
concordance with voltage LED
strips to be connected)
Current
Depending upon the load to be
controlled up to a maximum of 24A
Connection method
Screw terminal block
Cable cross-section
0.5-4mm² (IEC) / 10-30AWG (UL)
INPUTS SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of inputs
6
Inputs per common
6
Operation voltage
+3.3VDC in the common
Operation current
1mA @ 3.3VDC (per input)
Switching type
Dry voltage contacts between input
and common
Connection method
Screw terminal block
Cable cross-section
0.5-2.5mm² (IEC) / 26-12AWG
(UL)
Maximum cable length
30m
Maximum response time
10ms
WIRINGDIAGRAMS
RGB + W CHANNELS
RGBW CHANNEL
NOTE: The pole of
each channel in use must
be mandatorily
connected.
INDEPENDENT CHANNELS
Attaching Lumento DX4 to DIN rail:
Removing Lumento DX4 from DIN rail:
Description:
LED off
Blue LED On
Green LED On
P
: Prog. LED
C
x: Channel x
LED
P
Power supply
failure
P
Cx
Overload
Short-circuit
P
Overheating
time (s)
0
0.5
1
1.5
2
0
0.5
1
1.5
2
0
0.5
1
1.5
2
Figure 2: Error notification LED codes
* En el caso del sensor ZN1IO-DETEC-P, colocar su micro interruptor 2 en
posición Type B.
INPUTSCONNECTION
Any combination of the next accessories is allowed on the inputs:
Up to two motion sensors can be
plugged into the same device
input (parallel wiring)
Screw terminal for connecting
Zennio motion sensors*
Motion Sensor
Switch/Sensor/
Push button