Zerotech Vengeance 1-6X24 User manual

ZEROTECH RIFLESCOPES
INSTRUCTION MANUAL
vengeance (MODEL 1-6X24) /

‘ANY OWNER, ANY PROBLEM, ALWAYS COVERED’

3
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
CONTENTS
INTRODUCTION
LIFETIME WARRANTY
SCOPE FEATURES
SETTING THE DIOPTRE
MOUNTING YOUR SCOPE
ZEROING YOUR RIFLE
RESETTING THE TURRETS AFTER ZEROING
RETICLE ILLUMINATION FEATURE
BATTERY INSTALLATION
SCOPE CARE
RETICLES
WARRANTY & CONTACT INFORMATION
BULLET DROP DETAILS
ZEROTECH INFORMATION
4
5
6
7
9
11
14
15
16
17
18
19
20
21
PAGES

4ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
WELCOME TO THE ZEROTECH RIFLESCOPE FAMILY!
Customer First - We listened to you and came up with a family of riflescopes that will
satisfy the needs of our most discerning and experienced customers.
Backed by Experience - ZeroTech enjoys 55 years of experience in the Optics Market
supplying high quality brands to retailers throughout Australia and the Asia Pacific.
Built for the Australian Shooter - Designed and built to endure the harsh conditions of
the Australian bush and the exacting demands of the precision shooter.
Lifetime Warranty - Be safe in the knowledge that your scope is backed by our Triple A
Lifetime Warranty: ‘ANY OWNER, ANY PROBLEM, ALWAYS COVERED’
Bespoke Reticles - Practical Reticles for the Everyday Shooter.
INTRODUCTION

5
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
LIFETIME WARRANTY
BACKED FOR LIFE!
Be safe in the knowledge that your scope is
backed by our Triple A Lifetime Warranty:
- Fully transferable, covers accidental damage as
well as defects in materials and workmanship.
- No receipt or warranty card is required.
- We will repair or replace product with equal or
similar value and/or specifications.
- We will return product to you at no charge. ‘ANY OWNER, ANY PROBLEM,
ALWAYS COVERED’

6ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
Windage turret
Windage turret cap
Elevation turret
Elevation turret cap
Magnification power
change ring
Reticle illumination
adjustment dial
Illumination battery cover
Dioptre lock ring
Magnification
throw lever
Ocular
Objective
30mm maintube
VENGEANCE 1-6X24
SCOPE FEATURES

7
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
BEFORE YOU START USING YOUR SCOPE, IT IS EXTREMELY IMPORTANT
TO MAKE SURE YOU HAVE ADJUSTED THE DIOPTRE CORRECTLY. THE
CORRECT DIOPTRE SETTING WILL ENSURE THAT YOUR RETICLE REMAINS
CLEAR AND SHARP THROUGHOUT THE ENTIRE FOCAL RANGE OF YOUR
SCOPE. TO SET YOUR DIOPTRE, FOLLOW THE STEPS BELOW;
SETTING THE DIOPTRE
1. Loosen the dioptre locking ring and unscrew away
from the ocular for several revolutions.
2. Adjust the magnification to 1x.
3. Whilst looking through the scope at an object
between 15 to 50 metres away, rotate the ocular
until the object appears at true 1x magnification. - Loosen the
dioptre locking ring

8ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
NEVER LOOK THROUGH YOUR SCOPE DIRECTLY AT THE SUN.
4. Adjust the magnification to full power (6x) and confirm the reticle is well focused.
The reticle should appear sharp and crisp from edge to edge. Make small
adjustments on the ocular to sharpen the appearance of the reticle, if required.
5. Once the desired setting has been achieved, tighten the locking ring against the
ocular, being careful not to rotate the ocular and disturb the dioptre setting.
- Tighten dioptre locking ring
- Set magnification to
6 X. Confirm reticle is
sharp and crisp
- Set magnification to 1 X
- Rotate ocular to achieve
true 1 X image

9
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
- BEFORE MOUNTING YOUR SCOPE TO A FIREARM, IT IS ESSENTIAL THAT
YOU CONFIRM THAT YOUR FIREARM IS UNLOADED AND NO AMMUNITION
IS PRESENT IN YOUR WORKSPACE.
- TO AVOID DAMAGE AND TO PRESERVE YOUR WARRANTY, YOUR SCOPE
SHOULD ALWAYS BE MOUNTED BY AN EXPERIENCED PROFESSIONAL.
MOUNTING YOUR SCOPE
1. Once you are satisfied the base(s) is correctly fitted to the receiver of your firearm,
proceed to fit the rings to the base(s) and ensure the ring clamps are tightened to
the recommend torque settings as specified by the manufacturer.
2. With the ring tops removed, place the scope in the ring bases and gently slide the
scope back and fourth in the ring bases to ensure the scope slides freely. If the scope
does not slide freely, lapping of the rings may be necessary to avoid damage to the
scope maintube. ZeroTech always recommends the use of high quality rings and bases

10 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
to ensure the best possible fitting of your scope.
3. Avoid mounting the scope with the rings contacting the junction of the maintube/
erector housing, magnification ring/ maintube junction or the objective/ maintube
junction.
4. It is essential to confirm that no part of the scope is contacting the barrel or receiver
when the scope is mounted in the rings.
5. Once you have confirmed the fit of the scope in the ring bases, fit the ring tops and
tighten the ring top bolts to between 22–25 in lbs or 2.5–2.8NM.
6. ZeroTech highly recommends the use of a scope level (bubble level) fitted to the
rings or the scope maintube to ensure the reticle can consistently be aligned with
the fall of gravity every time a shot is fired. This is particularly important for precision
shooting applications.
*If your level mounts to the maintube of the scope, follow the same guidelines as observed
for scope ring fitting to ensure the level does not damage the maintube of your scope.

11
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
ZEROING DISTANCES
Centrefire Rifles: Zerotech recommends zeroing most centrefire rifles at approximately
100 metres +/- 10 metres. 100 metres enables the shooter to overcome any offset
problems caused by the centre height of the scope above bore but is not too far as to
accidentally build in an error due to unobserved environmental conditions such as wind. If
you have a low magnification scope, such as the Vengeance 1-6x24, you may wish to zero
your rifle at a closer distance.
Rimfire Rifles: Most commonly, rimfire hunting rifles are zeroed at 50 – 75 metres
depending on the type of ammunition being used. Rimfire target rifles may have different
zeroing requirements depending on purpose.
We always recommend that you zero your rifle in the same manner as you typically
shoot your rifle. For example, if you mainly shoot your rifle from a bench, zero your
ZEROING YOUR RIFLE

12 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
rifle by shooting from a bench. If you predominately shoot your rifle in the prone
position, zero your rifle from the same position.
Before you fire your first shot, you should bore sight your rifle to ensure your scope and
your barrel are both aligned at the intended point of impact on your target.
To do this with a bolt action rifle, remove the bolt with the rifle securely supported (front
and rear) and align the bore with the target. Without disturbing the rifle, carefully look
through the scope and check that the reticle is also aligned with the same point as the
bore on the target. If the reticle is not aligned, use the windage end elevation adjustments
on your scope to adjust the reticle to the intended point of impact on the target.
Once you are satisfied that the scope and the bore of your rifle are aligned to the same
point on the target, fire a shot at the target and observe the point of impact (bullet hole).

13
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
If required, use the windage and elevation turrets on your scope to adjust the bullet impact.
Dialling the elevation turret in the direction of the ‘U’ symbol will adjust the bullet impact
upwards on the target. Likewise, dialling the windage turret in the direction of the ‘R’
symbol will adjust the bullet impact to the right on the target.
�If your scope turrets are indexed in ¼ Minutes of Angle (0.25 MOA), each ‘click’ of
your scope turret will adjust you bullet impact approximately 7-8mm at 100 metres
(approx. ¼” at 100 yards).
�If your scope turrets are indexed in ½ Minutes of Angle (0.5 MOA), each ‘click’ of your
turret will adjust your bullet impact approximately 15mm at 100 metres (0.5” at 100
yards) or 7-8mm at 50 metres (0.25” at 50 yards).
�If your scope turrets are indexed in 0.1 Milrad (0.1 MRAD), each ‘click’ of your scope
turret will adjust your bullet impact 1cm at 100 metres (0.36” at 100 yards).

14 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
RESETTING THE TURRETS AFTER ZEROING
Once you have obtained a zero on your rifle/
scope, you can remove the windage and
elevation turrets using a 2mm hex key.
1. Unscrew and remove the elevation turret
centre bolt.
2. Slide the elevation turret completely away
from the scope body and re position,
ensuring that the ‘0’ index mark on the
turret lines up with the vertical index mark
on the main tube.
3. Re-fit and tighten the turret centre bolt
and double check the turret is in the ‘0’
position.
4. Repeat this process for the windage turret.
Use a 2mm hex key
to remove the turret
centre bolt
Re-fit the turret and
ensure the ‘0’ is
indexed with the
vertical index mark
on the main tube

15
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
RETICLE ILLUMINATION FEATURE
1. Vengeance 1-6x24 models are equipped with a reticle
illumination feature.
2. Before use, you will need to remove the illumination
dial battery cap and discard the plastic circuit blocker.
3. The CR2032 button battery can then be reinstalled
and the illumination dial battery cap refitted.
4. The illumination function has 6 different reticle
brightness settings as well as an “Off” function
between each brightness setting.
5. Be sure to switch your reticle illumination setting to
the “Off” position when your rifle is in storage or
in transport.
6. We always recommend to carry a spare CR2032
button battery when you’re using your rifle, especially if you’re heavily reliant on the
illumination function.

16 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
SCOPE CARE
REMOVING THE ILLUMINATION BATTERY COVER
Insert battery here

17
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
SCOPE CARE
1. Wipe dust and debris from your scope body using a damp microfibre cleaning cloth.
2. If necessary, clean dust and dirt from the scope lenses using a lens brush and the
ZeroTech lens cleaning cloth.
3. Never spray cleaners or solvents on any part of your scope. Irreversible damage
may be caused by such products.
4. Avoid touching the scope lenses. Wipe fingerprints off the scope lenses using the
ZeroTech lens cleaning cloth.

18 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
RETICLES
Your new Vengeance 1-6x24 riflescope comes fitted
with a reticle designed in-house by ZeroTech.
ZeroTech scopes feature a range of different reticles,
designed specifially to help you maximise your
shooting experience.
For further information visit the Reticles page on our
website by scanning the QR code.
PRACTICAL RETICLES FOR THE EVERYDAY SHOOTER.
zerotech.com.au/reticles

19
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
WARRANTY & CONTACT INFORMATION
Ph: [phone]
Email: [e-mail]
For global partners scan
the QR code below.
Please direct all enquiries to [email protected]om.au
Company details;
ZEROTECH INTERNATIONAL PTY LTD
Address:
PO BOX 7200,
Warringah Mall,
NSW, 2100
AUSTRALIA
zerotech.com.au/global-partners

20 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
CARTRIDGE: PROJECTILE: VELOCITY:
TWIST RATE: ZERO DISTANCE:H.O.B.**:
BC*:
* BC = BALLISTIC COEFFICIENT ** H.O.B. = HEIGHT OVER BORE
DIST. ELEVATION DIST. ELEVATION DIST. ELEVATION
DISTANCE 100m 325m 500m
150m 350m 525m
200m 375m 550m
225m 400m 575m
250m 425m 600m
275m 450m 625m
300m 475m 650m
BULLET DROP DETAILS