ZETTLER 602SB User manual

MZX Fire detection system 602SB
Fixing instructions Doc. version 5.0 1/6
602SB Type ‘A’ Sounder Base - Installation
Instructions
Technical Specifications
Electromagnetic Compatibility
The 602SB complies with the following:
 Product family standard EN50130-4 in
respect of Conducted Disturbances, Radiated
Immunity, Electrostatic Discharge, Fast Tran-
sients and Slow High Energy.
 EN50081-1 for emissions.
Introduction
The 602SB Intelligent Sounder Base provides an
additional sounder function on the MXC detec-
tion circuit.
Fig. 1: 602SB Sounder Base
Parameter Value
System Compatibility Use only with MXC
Fire Alarm Controllers
Environment Indoor Application
only
Operating Tempera-
ture -25oto +70oC
Storage Temperature -40oto +80oC
Operating Humidity Up to 95% non-con-
densing
Height 37.5mm
Diameter 107.8mm
Weight 0.192kg
Table 1: Specifications
Yellow temporary
park plunger
Mounting Require-
ments
Flat surface or electri-
cal backbox with
50mm fixing centres
with the 4" flange.
Minimum Wire Size 1.5mm2
Maximum Wire Size 2.5mm2
Standby current
(Dumb Mode)
<100μ
Standby current (Intel-
ligent Mode, for
future use)
<1.5mA
Alarm current full vol-
ume (90dBA)
6.8mA
Alarm Current low
volume (68dBA)
1.2mA at low volume
Protocol Fulleon PIU and Tyco
CAUTION
Ensure that the site plan defines the
polarity of polarity conscious bases
Parameter Value
Table 1: Specifications

2/6 Fixing instructions Doc. version 5.0
602SB MZX Fire detection system
The 602SB Sounder Base may be used with or
without an associated detector. When used
with an associated detector, removal of any
detector or loss of power to the detection circuit
may cause the sounder to cease
operating. When used without an associated
detector, the wiring should be as shown in the
alternate wiring scheme. A cap Part No.
557.001.040.A.T.Y should be fitted in place of a
detector.
Features
The 602SB Sounder Base provides eight tone
and variable volume settings.
Wiring Notes
The following notes apply:
 All wiring must conform to the current edition
of IEE Wiring Regulations and BS 5839 Part 1.
 All wiring must be free of earths.
Setting Sounder Output
Options
The sounder outputs are set as follows:
 Tone - using the 4-way DIL switch (Fig. 3 and
Table 2 refer).
 Volume - using the trimmer tool (S/C No.
517.050.015) (Fig. 3 refers).
DIL Switch Settings
1 2 3 4 Response
Sound
Marketing
Tone No.
000xDutch 7
Table 2: DIL Switch Settings
001xTemporal4 -
010xSlowSweep 3
0 1 1 x March Time Beep 25
100xFastSweep 2
101xTemporal3 -
110xTwoTone 11
1 1 1 x Continues 14
Fig. 2: Connections to 602SB Sounder Base
DIL Switch Settings
1 2 3 4 Response
Sound
Marketing
Tone No.
Table 2: DIL Switch Settings

MZX Fire detection system 602SB
Fixing instructions Doc. version 5.0 3/6
Installation to a Flat
Surface or Electrical
Backbox
To install a sounder base, proceed as follows:
1 Feed the detection circuit wiring through the
mounting flange cable entry.
2 Secure the mounting flange to either an elec-
trical backbox or a flat surface as required.
3 Feed the detection circuit wiring through the
sounder base cable entry, then clip the
sounder base to the mounting flange.
4 Wire the sounder base as shown in Fig. 2
ensuring correct polarity.
Fig. 3: 602SB Sounder Base
Tone selection switches
Volume adjuster (clockwise to increase)
Volume trimmer tool
CAUTION
Do not fill the sound gap between the
mounting flange and the sounder base.
LPCB approval
For LPCB approval, detectors and caps
must be locked into the sounder base
using a locking device (Factory fitted).
Ensure that the locking device is in place
before fitting a detector or cap. See Fig.
5.

4/6 Fixing instructions Doc. version 5.0
602SB MZX Fire detection system
Cabling
Cables are to be selected in accordance with
Publication 17A-02-D1 and the requirements of
the current issue of BS5839. A maximum of 2 x
1.5mm2or 1 x 2.5mm2cable may be connected
at any one terminal.
Fig. 4: Installation
Fig. 5: Locking Device

MZX Fire detection system 602SB
Fixing instructions Doc. version 5.0 5/6
CPR Information
Tyco Fire & Security GmbH,
Victor von Bruns-Strasse 21,
8212 Neuhausen am Rheinfall,
Switzerland
15
2831-CPR-F1987
21
0832-UKCA-CPR-F0123
DoP-2015-4056
EN54-3:2001 + A1:2002
Conventional Type A sounder base for use in fire detec-
tion and alarm systems in buildings
602SB
Essential Characteristics
EN54-3:2001 + A1:2002
Performance under fire condition: Pass
Operational reliability: Pass
Durability of operational reliability: temperature resist-
ance: Pass
Durability of operational reliability; humidity resistance:
Pass
Durability of operational reliability; corrosion resistance:
Pass
Durability of operational reliability: shock and vibration
resistance: Pass
Durability of operational reliability; electrical stability: Pass
Durability of operational reliability: resistance to ingress:
Pass
Installation Instructions: 120.415.559_01B-9-I3

602SB MZX Fire detection system
120.415.559_01B-9-I3, doc. version 5.0, 31. January 2022
© 2022 Johnson Controls. All rights reserved. All specifications and other
information shown were current as of document revision date and are subject
to change without notice.
www.zettlerfire.com
Tyco Fire & Security GmbH, Victor von Bruns-Strasse 21, 8212 Neuhausen
am Rheinfall, Switzerland