Zhejiang Dahua Security Technology IPC-HD1100C User manual

Dahua HD Mini Network Dome Camera User’s Manual
Version 1.2.1
Zhejiang Dahua Technology CO., LTD.

i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please
note: Do not connect these two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Installation Accessories bag
1
Quick Start Guide
1
CD
1
Warranty Card and Certificate
1

iv
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
2Framework...................................................................................................................................9
2.1 Structure ........................................................................................................................9
2.2 Dimensions..................................................................................................................10
3Installation..................................................................................................................................13
3.1 Device Installation......................................................................................................13
4Quick Configuration Tool.........................................................................................................15
4.1 Overview......................................................................................................................15
4.2 Operation.....................................................................................................................15
5Web Operation..........................................................................................................................17
5.1 Network Connection...................................................................................................17
5.2 Login and Main Interface...........................................................................................17
6FAQ ............................................................................................................................................19
Appendix Toxic or Hazardous Materials or Elements ...............................................................20

1
1 General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
audio and video data collection, transmission together. It can connect to the network directly without
any auxiliary device.
This series network camera uses standard H.264 video compression technology and MJPEG audio
compression technology, which maximally guarantee the audio and video quality.
This series network camera enclosure has the strong resistance capacity, which can guarantee the
proper work performance under heavy strike. It supports real-time monitor and motion detect function.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration
and setup in schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support network storage such as FTP.
Alarm
Function
Real-time respond to video detect as user pre-defined activation setup and
exert corresponding message in screen and audio prompt(allow user to pre-
record audio file)
Real-time video detect: motion detect, camera masking.
Can generate an alarm when network abnormal, Micro SD card abnormal
event occurred.
Network
Monitor
Network camera supports one-channel video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
RTP/RTCP, RTSP and etc.
Support web access, widely used in WAN.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support various network protocols.
Power
External power adapter DC12V
Support PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Day/Night mode auto switch.
Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.
Support digital WDR.
Support system resource information and running status real-time display.

2
Support video watermark function to avoid vicious video modification.
Support electronic shutter and gain setup.
Support dual bit stream, support ACF.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
Parameter
IPC-HD1100C
IPC-HD1105C
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/4-inch CMOS
Pixel
1280(H)*720(V)
Day/Night
Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Off/BLC/WDR (1-100)/HLC(anti-flicker is outdoor and is valid only when
exposure mode is auto with range 1-100)
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Video
Compression
Standard
H.264/H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream (1280*720@25fps)
Extra stream (704*576@25fps)
NTSC:
Main stream (1280*720@30fps)
Extra stream (704*480@30fps)
Video Bit Rate
H.264: 16Kbps-8192Kbps, adjustable
MJPEG adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror function.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
2.8mm/3.6mm/6mm/8mm MP
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function and
etc.

3
Video Loss
Activation event: video storage, image snapshot, log, email function and
etc.
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP,
UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Platform
interface
Standard
ONVIF
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
AUX Interf ace
Reset
Built-in RESET button
General Parameter
Power
Support DC12V and PoE
Note: 05 series do not support PoE.
Power
Consumption
DC 12V 3.1W MAX
DC 12V 2.5W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(m
m)
¢110×54
Weight
200g(excluding package)
Installation
Installed in the places such as wall or the ceiling
Model
Parameter
IPC-HD2200C-V2
IPC-HD2205C-V2
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
Pixel
2048(H)*1536(V)
Day/Night
Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Off/On
Electronic
Shutter
Manual/Auto/Low noise/Low motion blur
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Video
Compression
Standard
H.264/H.264B/H.264H/MJPEG

4
Video Frame
Rate
PAL:
Main stream (1920*1080@25fps)
Extra stream (704*576@25fps)
NTSC:
Main stream (1920*1080@30fps)
Extra stream (704*480@30fps)
Video Bit Rate
H.264H: 16Kbps-8192Kbps, adjustable
MJPEG adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror function.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
2.8mm/3.6mm/6mm. fixed focus.
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function and
etc.
Record
Record
Priority
Manual >Video detect>Schedule
Network
Wire Network
1-channel 10/100M Ethernet, RJ45 port
Network
Protocol
Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP,
UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
AUX Interf ace
Reset
Built-in RESET button
General Parameter
Power
Support DC12V and PoE
Note: 05 series do not support PoE.
Power
Consumption
DC 12V 3W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(m
m)
¢110×54
Weight
200g(excluding package)
Installation
Installed in the places such as wall or the ceiling

5
Model
Parameter
IPC-HDB4100C-A
Series
IPC-HDB4200C-A
Series
IPC-HDB4300C-A
Series
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
1/2.8-inch CMOS
1/3-inch CMOS
Pixel
1280(H)*960(V)
1920(H)×1080(V)
2048(H)×1536(V)
Day/Night
Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Off/BLC/WDR (1-100)/HLC(anti-flicker is outdoor and is valid only when
exposure mode is auto with range 1-100)
Electronic
Shutter
Manual/Auto
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream
(1280*960@25fps)
Extra stream 1
(704*576@25fps)
Extra stream 2
(1280*720@8fps)
PAL:
Main stream
(1920*1080@25fps)
Extra stream 1
(704*576@25fps)
Extra stream 2
(1280*720@11fps)
PAL:
Main stream
(2048*1536@20fps)
Extra stream 1
(704*576@20fps)
Extra stream 2
(1280*720@1fps),
Main stream
(1920*1080@25fps)
Extra stream 1
(704*576@25fps)
Extra stream 2
(1280*720@11fps)
NTSC:
Main stream
(1280*960@30fps)
Extra stream 1
(704*480@30fps)
Extra stream 2
(1280*720@1fps)
NTSC:
Main stream
(1920*1080@30fps)
Extra stream 1
(704*480@30fps)
Extra stream 2
(1280*720@1fps)
NTSC:
Main stream
(2048*1536@20fps)
Extra stream 1
(704*480@20fps)
Extra stream 2
(1280*720@1fps),
Main stream
(1920*1080@30fps)
Extra stream 1
(704*480@30fps)
Extra stream 2
(1280*720@1fps)
Note:
Extra stream 2’s actual frame depends on max capacity set which can
be adjusted within its range.
Video Bit Rate
H.264H: 40Kbps-8192Kbps adjustable
MJPEG: 40Kbps~16384Kbps adjustable and bit rate is adjustable.
Support customized setup.

6
Video Flip
Support mirror function.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
ROI
Support max 4 ROI.
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask, overlay.
Lens
2.8mm/3.6mm/6mm/ fixed focus
Lens Interface
M12. Lens is the default accessories
Audio
Audio Input
1-channel built-in MIC
Audio Bit Rate
8kbps 8bit/16kbps 16bit
Audio
Compression
Standard
G.711A/G.711Mu/PCM
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function and
etc.
Video Loss
Activation event: video storage, image snapshot, log, email function and
etc.
Record and Backup
Record
Priority
Manual> Video detect>Schedule
Local Storage
Support Micro SD (64GB) card storage, NAS storage
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP,
UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP, QoS, 802.1x.
Platform
interface
Standard
PSIA, ONVIF
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
AUX Interf ace
Reset
Built-in RESET button
General Parameter
Power
Support DC12V and PoE
Note: 05 series does not support PoE.
Power
Consumption
DC 12V 2.5W MAX
DC 12V 3W MAX
Working
Temperature
-20℃~+60℃
Working
Humidify
≤95%
Dimensions(m
m)
¢110×54
Weight
0.25Kg
Installation
Installed in the places such as wall or the ceiling

7
Model
Parameter
DH-IPC-HD1100C-W
DH-IPC-HD2200C-W
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/4-inch CMOS
1/3-inch CMOS
Pixel
1280(H)*720(V)
2048(H)*1536(V)
Day/Night
Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Off/BLC/WDR (1-100 adjustable)/HLC(anti-flicker is outdoor and is valid
only when exposure mode is auto with range 1-100)
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Video
Compression
Standard
H.264/H.264B/MJPEG
H.264/H.264B/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream (1280*720@25fps)
Extra stream (704*576@25fps)
PAL:
Main stream (1920*1080@25fps)
Extra stream (704*576@25fps)
NTSC:
Main stream (1280*720@30fps)
Extra stream (704*480@30fps)
NTSC:
Main stream (1920*1080@30fps)
Extra stream (704*480@30fps)
Video Bit Rate
H.264: 16Kbps-8192Kbps,
adjustable
MJPEG adjustable and bit rate is
adjustable.
Support customized setup.
H.264H: 16Kbps-8192Kbps,
MJPEG adjustable and bit rate is
adjustable.
Support customized setup.
Video Flip
Support mirror function.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
2.8mm/3.6mm/6mm/ fixed focus
2.8mm/3.6mm/ fixed focus
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function and
etc.
Video Loss
Activation event: video storage, image snapshot, log, email function and
etc.
Record and Backup
Record
Priority
Manual> Video detect>Schedule

8
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Wireless
Network
IEEE802.11a/b/g/n，built-in antenna
Network
Protocol
Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP,
UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
Access
Protocol
Support international, ONVIF
AUX
Interface
WPS
WI-FI one key connection
Reset
Built-in RESET button
General Parameter
Power
Support DC12V
Power
Consumption
DC 12V 3.8W MAX
DC 12V 4.3W MAX
Working
Temperature
-30℃~+50℃
Working
Humidify
≤95%
Dimensions(m
m)
¢110×54
Weight
200g(excluding package)
Installation
Installed in the places such as wall or the ceiling

9
2 Framework
2.1 Structure
Please refer to the following figure for detailed information. See Figure 2-1 and Figure 2-2.
Note:
Figures in this chapter are for reference only. Different product models may refer to different figures.
Please use figure (a) or (b) according to the actual product.
Figure 2-1 Structure (a)

10
Figure 2-2 Structure (b)
Please refer to the following sheet for detailed structure information.
Please refer to the following sheet for detailed port information.
2.2 Dimensions
SN
Name
1
X-Y-Z rotation module
2
Device lens
3
Dome camera enclosure
SN
Name
Function
4
Power input port
Connect to the DC 12+ power to
input the power.
5
Network port
Network data input, output and
PoE.
Note:
Some devices do not support
PoE.
Before making crystal
head, pull the anti-dust,
waterproof cover through
network cable.
6
MIC hole
Audio input

11
Please refer to the following figure for the dimension information. The unit is mm. See Figure 2-3
through Figure 2-5.
Figure 2-3 Dimension illustration 1
Figure 2-4 Dimension illustration 2

12
Figure 2-5 Dimension illustration 3

13
3 Installation
3.1 Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Please refer to the steps listed below.
Figure 3-1 Device installation illustration 1
Figure 3-2 Device installation illustration 2
Step1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover
and then open the cover.
Step 2
Please take the installation map in the accessories bag, and then paste it on the ceiling or the wall
according to your monitor area requirements.

14
Step 3
Draw and then dig three plastic expansion bolts holes on ceiling or other installation surface and then
insert three expansion bolts in the holes. Secure these three bolts firmly.
Note:
Please dig a “cable exit hole” in the surface according to the installation map if you want to draw
out the cable from the top of the installation surface.
You need to use the proper tool to open up the side port of the U-cable channel of the dome
camera pedestal if you want to draw out the cable from the side port of the cable channel when
you are installing the device cable. And then you can draw out the cable from the cable channel of
the pedestal.
Step 4
Adjust the device installation pedestal to the proper position and then draw the cable through the cable
exit you just dug in the ceiling (wall). Line up the TOP direction of the device to the installation map
and then line up the three screw holes in the device pedestal to the three plastic expansion bolt holes
in the installation position. Put the three self-tapping screws in the three plastic expansion bolts firmly.
Now the dome camera is secure in the installation surface.
Step 5
Loosen the two M3 secure screws of the lens rotation structure (Do not remove, loosen a little bit will
be OK.). Use the inner hexagonal wrench to insert them to the inner hexagonal holes and then use the
wrench to turn the lens. Adjust the lens to the proper monitor angle and then secure the screws of the
lens rotation structure. The lens adjust angle ranges are: flip (0°~+75°), video pan rotation (-15°~+15°) ,
video rotation angle(-15°~+15°).
Step 6
Line up the dome camera cover to the cable exits and put the cover back. Use the inner hexagonal
wrench to secure the three inner hexagonal screws firmly. Now the installation completed.
Note:
If you want to restore default settings of device, you shall open device front cover, and press
Reset button in Figure 3-2 with power on for 10s.
If you want to use WPS function of device, you shall open device front cover, and press Reset
button in Figure 3-2 with power on for 1-2 seconds, then press the WPS button of the router,
generally the device will connect to corresponding router within one minute (supported by
some series)

15
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1 Search interface
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 4-2 Search interface 2
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.