Zhejiang Longyard Trade Industrial BS-T1B User manual

Metal Garden Shed
OWNER'S MANUAL
Instructions for Assembly
Requires two people and takes 1 hour for lnstallation.
Quick & Easy Assembly
Ridge Reinforced Walls
·1·
BS-T1B

·2·
BEFORE YOU START
Owner's Manual
Prior to installation, it is important that you contact your local government authority to
determine if building approval is required. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.
Assembly instructions
Instructions are supplied in this manual and contain all appropriate information for your
building model. Review all instructions before you begin. During assembly, follow the
step sequence carefully for correct results .
Parts
Check to be sure that you have all the necessary parts for the building.
Separate contents of the carton by the part number while reviewing parts list.
Familiarize yourself with the hardware and fasteners for easier use during construction.
These are packaged within the carton. Note that extra fasteners have been supplied for
your convenience.
TOOLS MAY REQUIRED
Use heavy duty gloves when handling steel sheets and flashing
PLAN AHEAD
Site Selection
lAvoid overhanging trees as much as possible as leaves will make regular cleaning
necessary and broken branches are a potential hazard.
lSmall trees,bushes or fences nearby can be helpful,acting as a wind break.
Site Preparation
The site must be prepared so that the base of the shed is level all round and checking
with a spirit level is required.
The base can be constructed by treated timber or concrete,in order to stop the moisture
getting into the shed.The shed is not designed to be built onto lawn directly.Also the
ground will get muddy during rainy days.
If a concrete pad is made,it is important that this slopes towards the edges to prevent
water ingress.
Time must be allowed for any concrete or cement to dry before building the shed on top.
Bases can also be constructed from bricks,blocks,or mounted on a concrete pad.
The bricks or blocks should be cemented onto firm and level concrete footings and the
base frame drilled and screwed to the base.
IMPORTANT NOTES:
lFind someone to help you:it is much easier with someone to hold parts,pass tools
ect.Also some steps require two people to lift structures together.This is not very
heavy work so would suit most able-bodied people.
lAllow plenty of time:rushing often causes errors and the re-doing of incorrect
assemblies.If you have never built a shed before,it can take most of a day to carefully
complete the construction.
lHave the right tools to hand.
lSafety clothing as recommended in the 'Tools' section.
lIdeally lat out the parts and check that all are present before commencing
construction.Lay on cloths or plastic sheets if there is any risk of scratching the parts.
lTighten all nuts carefully,being sure not to miss any.Check the frame is square and
using a spirit level to check that it is upright.
PLAN AHEAD
Watch the weather:
Please be sure the day you select for installation is dry and calm.
DO NOT attempt to assemble your shed in windy weather
because of risk of damage to panels, or personal injury. Be careful
of wet or muddy ground.
Teamwork:
Whenever possible, two or more people should work together to
assemble the building. One person can position parts or panels
while the other is able to handle the fasteners and the tools.
ø2.4&ø55.5X7
PH1

PART
NO. Qty.
P1 4
1080mm
P2
1080mm
1
GC
F1
F2
190
30
S2
70
S3
132
G1
G2
3
1
4
G4
4
W1
1
G3
GF 2
4
F3 20
1080mm
P3 1
4
J1
2
J2
1200mm
1
PART
NO. Qty.
1
1
1
1
2
3
PART
NO. Qty.
PART
NO. Qty.
1229X683mm
1
1479mm
944mm
1479mm
1290mm
1
1290mm
·3·
4L
4R
32
33
13
1080mm 2
1090mm
14 1
1
1
15
16
17
890mm
18
890mm
1
1
1469mm
1476mm
19
20
1
1
21
22
23
1521X991mm
1229X664mm
1
1
1
1
2-1
944mm
1
34 1
2
K1
F4 4

·4·
P1
P1
P1
P1
P3
P2
14
13
13
2
2-1
1
3
4L
4R
20
19
22
23
J1
J1
18
17
16
15
GF
GF
K1
K1
21
32
W1
G3
34
G4
G4
J1
J1

1、When diagonal measurements are
equal,the frame is square.
2、The Floor Frame must be
BOTH square AND level or the
holes will not line up properly.
F1
·5·
1
2
2-1
3
x1x1
13
x1
2x1 2-1
F1
J1
F1x 24
J1 x 4

Wall panels ALWAYS attach to the Floor Frames with
Screws in the manner shown above .Rest the Panel
on the Floor Frame and the holes in the Panel
should line up with the holes in the Frame
F1x8S3 x8
4Rx 14Lx 1
·6·
4L 4R
F1
S3
F1
F1
F1
S3
3

F2x4
P1 x 2
F1x15 S3 x19
P2 x 1
13 x 1
·7·
P1
P1
P2
F1
F2
13
ⅠⅡ
ⅢⅣ
F2
F1
S3
F1
S3

F2x4
P1 x 1
F1x14 S3 x18
13 x 1
·8·
P3
14
P1
13
F2
14 x1
F2
ⅠⅡ
ⅢⅣ
P3 x1
F1
F1
S3
S3

F2x 2
P1 x 1
F1x 25 S3 x27
·9·
19
19 x1
20
F2
P1
20 x 1
ⅠⅡ
Ⅲ
F1
S3
F1
F1
S3

F2 x4 F1x24 S3 x24
·10·
15 x116 x1
16
15
GF x2
GF
GF
15
17x118x1
16
17
17
18
F2
GF
F1
S3

F3 x8 F1x34
·11·
K1x2
K1
K1
W1x4
W1
W1
W1
W1
G4 x4
G4
G4
34x1
34
F3
ⅠⅡ
Ⅲ

·12·
G2 x1
23 x1
23
G2

F3 x 10
·13·
F3
F4
34 G1
F3
G1
F1x 2
G1x234 x 122x123x1
23
22
F1
F4x2

·14·
F1x 12
F4
G1
G1x121x 1
F4x2
F1

·15·
F1x 2
G3 x132 x1
G3
32
F1

·16·
F1x 2
F1

·17·
F1x 4S3 x4
S3
F1

·18·
J2
J2
J2 x2