Zig Zag KMC3500 User manual

Zig-Zag
Message Center
Assembly
Instructions
Model# KMC3500

Before assembly, please make sure all components
are included.
(2) Large Vertical
Double Message
Center
AMC-A0004
(1) Middle Large Vertical
Double Message Center
AMC-A0008
(2) Large Vertical
Roof
AMC-A0009
(1) Middle Large Vertical
Roof
AMC-A0010
(2) Inground Post
Assembly
AMC-A0006
(2) Inground Outer
Post
AMC-P0016

Required Tools
(6) - 1/4" Flat Washer
(6) - 1/4"-20 x 3.50" Lag Screw
(16) - 3/8" Flat Washer
(4) - 3/8" x 5.00" Hex Head Bolt
(12) - 3/8" x 6.50" Hex Head Bolt
Before assembly, please make sure all hardware
is included.
-Power drill/Screw gun
-7/16" Socket
-9/16" Socket
-Level
-Guide wires
-Wood for bracing
-Post hole filler.

2X4 SPACER
FACING DOWN
2X4 SPACER
FACING UP
ROOF HOLE
3/8" X 6.50"
HEX HEAD BOLT
3/8" FLAT WASHER
Components required for Step 1:
(1)Middle Large Vertical Double Message Center
(2)Inground Post Assembly
Hardware required for Step 1:
(6) 3/8" x 6.50" Hex Head Bolt
(6) 3/8" Flat Washer
Step 1:
Lay out the required components as shown in the illustration. Attach the Inground
Post Assemblies to the Middle Large Vertical Double Message Center as shown.
Be sure to properly orientate posts as indicated. Place posts into post holes,
leveling where necessary. Fill post holes with filler.
Before Step 1 can be completed, two holes must be dug 41"
apart on center at a depth of 30" - 36". Make each hole
approximately 10" wide in diameter. These holes will be used to
construct middle section of the Zig Zag Message Center. Refer
to post hole layout at end of instructions for more detail.

2 POST HOLES
3/8" X 5.00"
HEX HEAD BOLT
3/8" FLAT WASHER
ROOF HOLES
H
3 POST
HOLES
Components required for Step 2:
(1)Inground Outer Post
(1)Large Vertical Double Message Center
Hardware required for Step 2:
(2) 3/8" x 5.00" Hex Head Bolt
(2) 3/8" Flat Washer
Step 2:
Lay out the required components as shown in the illustration. Attach the Inground
Outer Post to the Large Vertical Double Message Center as shown using the
indicated hardware. Repeat step for second Large Vertical Double Message
Center.

3/8" X 6.50"
HEX HEAD BOLT
3/8" FLAT WASHER
Before Step 3 can be completed, two hole must be dug 40"
apart on center from previously dug holes at a depth of 30" -
36". Make each hole approximately 10" wide in diameter. These
holes will be used to construct end section of the Zig Zag
Message Center. Refer to hole layout at end of instructions for
more detail.
Step 3:
Place End Section of Zig Zag Message Center
into post hole and attach to Middle Section of
Zig Zag Message Center as shown. Use the
supplied 3/8" x 6.50" Hex Head Bolt. Level
where necessary and fill hole with filler.
Repeat step for second end section.
Components required for Step 3:
Hardware required for Step 3:
(3) 3/8" x 6.50" Hex Head Bolt
(3) 3/8" Flat Washer

I
SECOND ROOF
HOLE LOCATION
1/4" FLAT WASHER
1/4"-20 X 3.50"
LAG SCREW
LARGE VERTICAL
ROOF
Components required for Step 4:
(2)Large Vertical Roof
(1)Middle Large Vertical Roof
Hardware required for Step 4:
(6)1/4"-20 x 3.50" Lag Screw
(6)1/4" Flat Washer
Step 4:
Attach Large Vertical Roof to Large Vertical Double Message Center as shown.
Secure Roof using the supplied 1/4"-20 x 3.50" Lag Screw. Note that the other
Roof hole is located on opposite side of message center. Repeat step for each
section of the Zig Zag Message Center.

41.000
40.000
40.000
57.280
REFERENCE
MEASUREMENT
STEP 2
STEP 1
STEP 2
DIG HOLES 10" WIDE
AT A DEPTH OF 30" - 36.00"
Post Hole Layout