ZIGBEE G07 User manual

G07 User Manual
1
G07 User Manual
Ver. 1.05
Copyright 2016 Nietzsche Enterprise Co., Ltd. All rights reserved
Nietzsche Enterprise reserves the right to make changes and improvements to its products without notice.
Contents
1) Package Content and Views of G07......................................................................................................................2
2) Installing Mounting for G07 .................................................................................................................................3
3) Powering On G07..................................................................................................................................................4
4) Connecting G07 to the Network...........................................................................................................................5
5) Configuring G07 in the Web Setting Homepage ..................................................................................................7
6) Sentrol Cloud Gateway Register........................................................................................................................ 13
7) Replacing G07 in Existing IoT Network.............................................................................................................. 14
8) Joining Other Devices to G07’s IoT Network..................................................................................................... 15
9) Removing Devices from G07’s IoT Network...................................................................................................... 15
10) Reset................................................................................................................................................................ 16
11) Product Specifications..................................................................................................................................... 16
Contact Information: Email: [email protected], Website: www.shop-wifi.com/wireless-sensors

G07 User Manual
2
Congratulations for choosing a world-class Total Solution with Controller Gateway using ZigBee,
Ethernet, and Wi-Fi wireless transmission technology. This manual is designed to help set up and get
the most from the sensor in a few short minutes.
Safety notice: Please read and follow the instructions before using this product
To prevent electrical shock or fire, do not disassemble or expose the unit to liquids of any kind.
Only use attachments and / or accessories specified by the manufacturer.
1 Package Content and Views of G07
NHR G07 Controller Gateway
Mounting fixtures (mounting cradle, 4 wall
plugs, 4 screws)
DC 12V Adapter
If any of the above is missing please contact your supplier.
Front
Bottom
Side
Back
Network LED
Wireless LED
Antenna
Power Switch
Power Socket
Ethernet Port
USB Port
Join Button
Reset Button
Alert LED
Unique MAC Address & Product Serial Number

G07 User Manual
3
2 Installing Mounting for G07
Requirements:
Mounting fixtures
Drill with 5mm (0.2 inches) drill bit size (if using wall plugs) or 3.5mm (0.14 inches) drill bit size
(if not using wall plugs)
Size 1 Phillips screwdriver
a) Locate G07 with at least 15cm (approx.. 6 inches) spacing on each side (except on mounting side)
avoiding the following sources of interference: direct sunlight, air flow from vents, fans, doors,
windows, heaters, sources of steam, oil vapor, etc.
b) If necessary, pre-drill mounting holes using mounting cradle for alignment, then use appropriate
drill bit to drill the holes –5mm (approx. 0.2 inches) if using wall plugs or 3.5mm (approx. 0.14
inches) if not using wall plugs.
c) If necessary, use a hammer to insert wall plugs into the 4 holes.
d) Use size 1 Phillips screwdriver to fasten the screws securing the mounting cradle. Note: pay
careful attention to the orientation of the mounting cradle.
e) Install and remove G07 using the following actions to ensure the mounting cradle has been
correctly and securely installed and G07 can be installed and removed.
Install - Remove -
Initial hardware installation for G07 has been successfully completed.

G07 User Manual
4
3 Powering On G07
Requirements:
DC 12V Adapter
a) Connect DC 12V adapter and plug into power socket.
b) G07 will take about 1-2 minute(s) to boot up. During the booting process, the NETWORK and
ALERT LEDs may both flash for about 2 seconds and light on for about 10 seconds.
c) After successful booting process, G07’s LEDs will indicate current status:
NETWORK LED
Status
Light on
Connected to the Cloud
Light off
Disconnected to the Cloud
Flashing
Reconnecting to the Cloud
ALERT LED
Alert Sound
Status
Light on
‘Beep’ x 30
Sentrol Cloud Away Mode (alarm is armed)
Flashing rapidly
Long ‘Beep’
Sentrol Cloud Panic Mode (alarm is activated)
Flashes 5 times,
then light off
N/A
Sentrol Cloud Home Mode (alarm is disarmed)
1 Flash every 5
seconds
‘Beep’ x 3
Sentrol Cloud Night/Sleep Mode (alarm is partially armed)

G07 User Manual
5
WIRELESS LED
Status
Light off
Stand by
1 flash every 2 or 3 seconds
Permit others to join
2 flashes
Device is joining or rejoining the Gateway and functioning normally
5 flashes
Device is removing from the Gateway
G07 has been successfully powered on.
4 Connecting G07 to the Network
Requirements:
Ethernet Cable(s)
Computer (running Windows)
Repeater or Ethernet switch (supporting DHCP connection mode) with internet connection
and an available Ethernet LAN port reserved for G07
NOTE: If you want to use Wi-Fi connection, please use a Wi-Fi repeater with several available
Ethernet LAN ports, or you can include a Wi-Fi repeater or access point within the same local
network hosting both your computer and your G07.
a) If necessary, remove G07 from the mounting cradle.
b) Power on G07 (See “Powering On G07”).
c) Make sure your computer is connected to the repeater or Ethernet switch with internet
connection.
Windows Computer
(Wi-Fi) Repeater /
Ethernet Switch
G07 Gateway
Ethernet Cable
Ethernet Cable
(for wired connection or Wi-Fi setup)

G07 User Manual
6
d) Initially your G07’s connection mode is set to DHCP (Dynamic Host Configuration Protocol) right
out of the factory. When your computer is connecting to your G07 for the first time, your
computer’s connection mode needs to be set to DHCP. (Using Windows 7 as an example) Go to
Start -> Control Panel -> Network and Sharing Center -> Change adapter settings -> Local Area
Connection -> Properties -> Internet Protocol Version 4 (TCP/IPv4) -> Properties. Make sure that
the options Obtain an IP address automatically and Obtain DNS server address automatically are
selected. Click OK.
e) Use an Ethernet cable to connect G07 to the same repeater or Ethernet switch that your computer
is connected to, or you can use an Ethernet cable to connect G07 to a repeater or Ethernet switch
that belong to the same local area network (with internet connection) of your computer.
f) Open a web browser on your computer and go to the website
http://www.sentrolcloud.com/nhr/view/front/download.php .
Please go to the folder Home -> Tools -> Gateway Finder . Right-click the GW_Finder RAR file icon
and select Download, then uncompress and install Gateway Finder to your computer.
g) Launch Gateway Finder. Click Search to search and display all of your G07 gateway(s) within the
same local network of your repeater or Ethernet switch, then double-click the MAC address of
your gateway (or you can manually open a web browser and manually enter the IP address of your
gateway).

G07 User Manual
7
NOTE: Your G07 may take about 1-2 minutes to boot. If you cannot find your gateway in Gateway
Finder, you may wait for your G07 to finish booting and search again.
h) When the login page appears, enter the username and password (default username and password
are both ‘admin’), then click Login to enter the G07 Web Setting Homepage.
5 Configuring G07 in the Web Setting Homepage
a) Your G07’s Web Setting Homepage has the following categories and sub-categories:
Category
Sub-categories
Network Setting
Ethernet Setting, WiFi Setting, Cloud Server Setting, 3G Setting
Date/Time
Time Setting
Management
Language, Account/Password, Automatic Logout Time, Initialize,
Save/Restore, Upgrade, Reboot
ZigBee Status
Coordinator Information, End Device Information
b) Unless stated otherwise, after making any changes in the G07 Web Setting Homepage, you will
need to click Confirm the change and let your G07 reboot (to make the changes effective).

G07 User Manual
8
c) Network Setting:
This category sets G07’s local and internet network options. G07 provides Ethernet, Wi-Fi, and
3G options to connect to a computer or to the cloud. When G07 is powered on or rebooted, it
will first search Ethernet for network connections. If no network connection exists on the
Ethernet, G07 will then sequentially search Wi-Fi and 3G for network connections. Once the
network connection to the cloud is successfully established, G07 will not change the network
connection until G07 is rebooted.
Ethernet Setting :
oGateway Name: Enter a name for your gateway (maximum 8 alphanumeric characters).
oConnection Mode: Select either Static IP or DHCP (default setting is DHCP). Normally
the connection mode is set to DHCP as this mode is much easier to use for most users.
However, if you want to you use your G07 in a network environment with static IP
infrastructure, you can also change the connection mode to Static IP before you adopt
your G07 to that network environment. In this case, you will need to manually assign
the following additional parameters: IP Address, Subnet Mask, Default Gateway, DNS 1,
and DNS 2. Please consult your network administrator for more details on these
parameters.
NOTE: If you set connection mode to Static IP, after G07 has rebooted you will need to
use the IP address assigned to your G07 in order to login to its Web Setting Homepage.

G07 User Manual
9
Wi-Fi Setting: If you want to use Wi-Fi connection, please disconnect the Ethernet from your
G07 after completing Wi-Fi settings below, then reboot your G07.
oChoose SSID : First click Scan to search for available Wi-Fi SSIDs nearby, then choose a
Wi-Fi SSID from the drop-down menu.
NOTE: Make sure that the SSID does not contain non-alpha-numeric characters.
oPer-Shared Key : Enter the password for the chosen Wi-Fi SSID.
Connection Mode : Same as that of Ethernet Setting. You can choose either Static IP or
DHCP (we recommend you to choose DHCP).
Cloud Server Setting: Sets parameters required for your G07’s cloud connection.
oIP : The default IP address is that of Nietzsche Sentrol Cloud server, 119.163.1.159. If
you want to connect to another cloud server, you can change the IP address to that of
another cloud server.
oPort: Default value is 10010.
oAES Function: Enables or disables AES encryption for data transmission (Enabled /
Disabled). The default option is Enabled. The use of AES encryption depends on the
cloud server to be connected to. If the cloud server requires AES encryption, then AES
Function needs to be set as Enabled.

G07 User Manual
10
oKey: AES Encryption Key. When AES encryption is enabled for data transmission, the
key entered in your gateway must match the key of the cloud server; otherwise the
communication will not be enabled.
oKey Confirm: Enter the AES Encryption Key again for confirmation.
3G Setting : If you want to use 3G connection, please disconnect the Ethernet from your
G07 after completing 3G settings below, then reboot your G07.
Please select or enter information provided by your 3G network service provider.
d) Date/Time:
Time Setting: Set up your G07’s System Time and Time Zone settings by configuring the
following parameters:
NTPD Service: Enables or disables NTPD (Network Time Protocol Daemon, a service that
automatically synchronizes G07’s current date and time settings periodically) (Enable /
Disable). The default option is Enable.

G07 User Manual
11
If NTPD is enabled, specify NTP Server and Update Interval.
NTP Server: Specify the NTP Server’s IP address (default is 118.163.1.157).
Update Interval: Specify the time interval after which your G07 will update time with the
NTP server (default is every 24 hours).
If NTPD is disabled, manually specify Current Time.
Current Time: A snapshot of current date and time will be displayed in text boxes
(example shown above is: 2016/3/15 08:00:17). You can change date/time directly by
modifying numeric values in these text boxes.
Time Zone: Select the time zone of your region from the dropdown list.
e) Management:
Language: Select a language (including English, Traditional Chinese, and Simplified Chinese)
for this web setting homepage. You will need to refresh the webpage or re-login for this
change to take effect.
Account/Password: The default username and password are both ‘admin’. You may enter
your own username and password. Note that after setting and applying your own username
and password, you will be automatically logged out, then you will need to use your own
username and password to login. The previous username and password will be unusable.

G07 User Manual
12
Automatic Logout Time: Sets the allowed time period of user inactivity before automatic
logout occurs.
Initialize: Resets this web setting homepage to factory default values. You can also press and
hold (with a sharp-pointed instrument) the hardware Reset button for 30 seconds for the
same initialization.
Save / Restore: Click Download Profile to save your G07 settings (configured in this web
setting homepage) as a G07 profile file on your computer, or click Upload Profile to restore
your G07 settings from a previously saved G07 profile file on your computer.
Upgrade: Displays your G07’s current firmware version with the online firmware upgrade
option. There are two ways to upgrade your G07 to the latest firmware:
Method 1 –Click Internet Upgrade and follow screen instructions.
Method 2 –Download the latest G07 firmware file to an USB drive’s root directory. Insert
the USB drive to your operating G07’s USB port. When the NETWORK and WIRELESS LEDs
flash simultaneously, the upgrade is complete. (Using a sharp-pointed instrument) Press the
hardware Reset button to reboot G07 with the upgraded firmware.
Reboot: Click Reboot to restart your G07, as this action is required for any changes made in
this web setting homepage to be effective (unless stated otherwise).
f) ZigBee Status :
Coordinator Information: You will see information relevant to your coordinator, e.g. End
Device (the number of end devices [i.e. child devices] connected to your gateway).
End Device Information: Displays technical information for all of your connected end devices
(i.e. child devices).

G07 User Manual
13
6 Sentrol Cloud Gateway Register
a) Go to http://www.sentrolcloud.com/nhr/view/front/newgateway.php
b) Enter the last 8 digits of G07’s MAC address in the space below “Gateway Mac”.
c) Enter the CAPTCHA code according to the page as shown below.
d) Click Continue button to proceed to the next page.
e) Create the account by entering “First Name”, “Last Name”, “E-Mail Address”, “Password”,
“Confirm Password” , select the display language and the time zone of your region, and check “I
agree to the terms of service”, then click Send Activation E-Mail as shown below.
f) Log in to the e-mail account that was entered and open the activation email to click “Click Here” to
complete the registration process.

G07 User Manual
14
7 Replacing G07 in Existing IoT Network
a) Login to Sentrol Cloud with your Sentrol Cloud account: http://www.sentrolcloud.com .
b) Select Administration Gateway.
c) Find the old gateway to be replaced and click that gateway’s corresponding Replace button.
d) Enter the last 8 digits of your new gateway’s MAC address (under “New Gateway MAC”) and the
on-screen CAPTCHA code, then click Replace Gateway. All profiles that have been using the old
gateway for IoT communications will now use the new gateway for the same IoT communications.

G07 User Manual
15
8 Joining Other Devices to G07’s IoT Network
Requirements:
Child device, such as repeater (eg. WZB-01USBR, WZB-02485R), or end device (eg. STH-01
series, STH-03ZB, S05 series)
Sharp pointed tool (if needed)
a) Ensure G07 is powered on (see “Powering On G07”) and ready to receive data from the Child
Device.
b) Ensure child device(s) to be joined to G07’s IoT network is/are in Ready to Join status (see relevant
device’s manual).
c) Apply 1 quick press to the Join button on G07, the green LED will flash once every 3 seconds for up
to 60 seconds to indicate the Permit Join status, allowing other devices to join to its IoT (Internet
of Things) network.
d) Check the status of the device to confirm it has been connected (see relevant device’s manual).
e) Repeat the above steps until all devices have been added successfully.
9 Removing Devices from G07’s IoT Network
Requirements:
Child device, such as repeater (eg. WZB-01USBR, WZB-02485R), or end device (eg. STH-01
series, STH-03ZB, S05 series)
Sharp pointed tool (if needed)
a) Ensure G07 is powered on (see “Powering On G07”).
b) Ensure the devices are powered on (see relevant devices’ manual) and is connected to G07 or its
repeaters.
c) Reset the child device (see relevant device’s manual; for Nietzsche IoT child devices, the reset
operation is to press and hold the S1 link switch for 3-5 seconds).
d) Check the status of the device to confirm it has been removed (see relevant device’s manual).
e) G07’s Wireless LED should return to light off.

G07 User Manual
16
10 Reset
Requirements:
Sharp-pointed instrument
a) Network Reset:
In the case where the G07 is no longer connected to the cloud, G07 will need to be reset by
applying a 10-second press to the Reset button (with a sharp-pointed instrument) until both the
Network LED and Wireless LED flash 3 times together. Then the Network LED will flash 3 times to
restart the gateway connection with the cloud.
Note: After reset, the G07 will restore all the default settings such as those of Ethernet, Wi-Fi,
ID/Password, etc.
Recommendation: Before removing power from G07 or resetting, please ensure its repeater
capability is no longer needed on the network by child device(s). Once G07 has been reset, it is
suggested to remove power from the G07 when not in use to reduce power wastage, RF traffic.
11 Product Specifications
Aggregator Network
ZigBee Home Automation
Connection to Cloud
Ethernet (default), WiFi, cellular (optional)
Internet Functionality
DHCP/ Static IP Web Setting
Nodes/Device Capacity
40 sensors, 10 actuators simultaneously
Wireless Network Protocol
IEEE 802.15.4, ZigBee2007 / PRO HA Profile
Transmission Range
Up to 300m / 984ft
Operating Frequency
2.4GHz ISM band
RF Output Power
18dBm
Receiver Sensitivity
-92dBm
Power Consumption
260mA in average
Transmission Interval
Always Standby
Network Topology
Star/ Tree/ Mesh
Power Supply
AC 100V~240V to DC 12V adapter
Operating Environment
-10 ~ +60°C , < 80% relative humidity
Dimensions
175(L) x 103(W) x 35(H) mm
Weight
255g

G07 User Manual
17
Certifications
CE/ FCC
Security Mechanism
AES128Bit Encryption
Connectors
RJ45 for Ethernet, 1 x USB , DC jack DC 12V adapter, SMA antenna
LED Indications
Network (Ethernet/ WiFi/ Cellular), Alert, Wireless (ZigBee)
Zero data-loss
Built-in 1G memory card when connection to Cloud is lost
Enabling Devices
End Device
NHR HA Devices
Repeater
S05-R / WZB-01USBR / WZB-02485R
Interoperability
Sentrol Cloud
Thank you for choosing NHR’s G07 Gateway. We are looking forward to working with you!