Zonton 999 Professional User manual

~T~ZONTON
999 Professional
FM Transceiver
THE USER S MANUAL

We are gratefulforyour purchase of this transceiver.
We believe this easy-to-use transceiver will provide you
withdependable and reliable communications.
We adopt advanced technology & workmanship for this
transceiver,we trust our aborative design will make it better
& quicker service for you.Forcorrect use, please read this
manualbefore use.
MODELSCOVERED BY THISMANUAL
ST-618:VHF FMTransceiver136-174MHz
ST-618:UHF FM Transceiver 350-390MHz
400-470MHz etc.
The transceiver apply for thesoftwareof QXPG-78D
NOTE:For avoiding mistakes,should read the data
first, then program.

FunctionOperation
Page
Channel Mode [DIAL](1second)+[LOW]
12
Frequency+Channel Mode[DIAL](1 second)+[DIAL]
12
Frequency Mode [DIAL](1 second)+[SCAN]
12
Adjust Squelch[FUNC](1second)+[LOW]
14
High/Low Power Press [LOW]
16
Channel Modeand Frequency
Add Channel Scan +Channel Mode.
17
[FUNC](1 second)+[SCAN]
ScanON Press [SCAN]
17
Manually Dialing Press [PTT] + Digits Key
19
Dial Saved DTMF Numbers [DIAL]+memoryunits(1-9)
19
Redial DTMF Numbers [DIAL]+[O]
19
Save DTMF Numbers[DIAL]+[#J, inputthe digits
(16 digits max.)[DIAL]+
20
memory units(1-9)
Confirm Saved DTMF Numbers[DIAL]+[*]+memory units(1-9)
20
Delete Saved DTMF Numbers [DIAL]+[D]+memory units(1-9)
20
Key Locked [FUNC](1 second)+[*]
21
[FUNC](1second)+[2].
Lightening Rotate[Circumrotate Encoder]
21
to choose background lights
Reverse Frequency[FUNC](1 second)+[3]
22
. QUICK-OPERATION liUIDE
FunctionOperation
Page
Frequency Mode
Stepping [FUNC](1 second)+[#)
22
Press[LOW] to choose
stepping level in circle
[FUNC](1 second)+[1].
VOXRotate [Circumrotate Encoder]
23
to choose gain level
[FUNC] (1 second)+ [A).Press
[LOW] to choose CTCSS/DCS/
Adjust Receiving OFF in circle,when in DCS,
CTCSS/DCS Decode press[DIAL] to choose Normal
24
or Inverted code.Rotate
[Circumrotate Encoder] to
choosecode.
[FUNC] (1 second)+[B]. Press
[LOW] to choose CTCSS/DC
Adjust Transmitting StOFF incircle,when in DCS,
CTCSS/DCS Encode press [DIAL] to choose Normal
24
or Inverted code.Rotate
[Circumrotate Encoder] to
choosecode.
Frequency Mode.[FUNC] (1
second)+ OPress[SCAN] to
Slip Frequency choose +/-slip frequency 25
Rotate[Circumrotate Encoder]
tochoose slip frequency value.

QUICK-OPERATION GUIDE PROMPTION
Function Operation Page
Wide/Narrow Band [FUNC](1 second)+[4]
26
Choose wide/narrow band incircle
ChannelMode and Frequency+Channe
Copy Channel Mode.[FUNC](1 second)+[C]
26
Rotate[CircumrotateEncoder] to
choose channel,pressPIT to save.
Frequency Mode.
Save Channel[FUNC] (1 second)+[C].
27
Rotate [ Circumrotate Encoder] to
choose channel,press PTT to save.
Channel Mode and Frequency+Channel
DeleteChannelMode.[FUNC](1 second)+[D].Rotate
27
[Circumrotate Encoder] to choose
delete channel,pressPIT to exit.
Copy Function with Press[lOW]+[MONI]+Power ON at the
same time.Press [MONI] to transmit
28
Cable data,then exit to power off and reboot.
The red indicator flashes when low battery,need to be
transmitting but it can still
communicate charged
The transmitting will stop when The voltage of battery is
the red indicator flashes and "Du" too low. Please charge at
sounds once
Out of lock,programmed
"Da da" sounds at intervals. frequency is out of the
range of the transceiver.
The transmitting(last a little while)TOT alert is ON.
will stop when hear "Du" soundsRelease PITto stop the
from speaker. alert tone.
The transmitting(last a little while)
will stop when hear a prompting TOT alertis ON.
voice.
Set Interval after TOT or
The transceiver transmits after a TOT resume time.After
while of the TOT alerts.limited timethe transce-
iver can transmit.
When receive signal from other
transceiver,the green light ON.
PressPIT to transmit and "Du" BCl function isON.
sounds heard,then retum to receive
signal.

PRECAUTION
For using this transceiver with high safetyand efficiency, please
read the following information carefully:
1.Repairing is only for qualified technicians.Please do not dis-
assemble the transceiver causally.
2.Do not modify the transceiver causally.
3. Power off when enter into the flammable and explosive places.
4. Please do not change or charge the battery when under the
flammable and explosive circumstances.
5.Please power OFF the transceiver before entering the explosive
and detonators areas.
6.To avoid the problem caused by electromagnetism interfering
orcompatibility,please power OFF when you entering into
the places where is not allowed to use the transceiver,such
as hospitals and airplanes.
7. Please put the device out of the range of the extensionof the
airbag in the car.
8. Do not expose the transceiver under sunshine for a long
time,nor place it close to heating appliances.
9.Please keep the antenna at least 2.5cm far away from you
when transmitting.
10.00 not put the device into the dusty,humid and wet areas,nor
put it into the rough surface.
11.lf the device smelled abnormally or smoking,please power
OFF atonce,and take out the battery,then contact with the
local distributor.
CONTENT
Unpacking and Checking Equipment·····---------------1
Supplied Accessories • - -.-••• --------.------- -.--- - - 1
Standard Accessories •---------------•••-. - - •• - - -. --2
Optional Accessories •----------------••••• - -. ---- - - 2
Battery ---------- - .. ----.. ---- .. - ------- . - - - - - - . - . -...- 3
Notes •••• - •••• - •••- •• - - -- -. - - - - - -. - _.- _•• _••-. -. -- 3
How to Charge - .... - - ------ - ---- - - -.----_. - - - -.------ - 4
Howto Store -- - ------------- - •- - •-•- -- ------------.4
Installing theAccessories . -.------ - - - - - -.-------.... 5. 7
Installing/Removing the Battery---- -. - - -•• ----. -.-.- -. 5
Installing/Removing theAntenna-••-. -. ---. - - - --.-----6
Installing/Removing the BeltClip----- - - •••• - - - •••••• _. 6
Installing/Removing theGallus- - -------- - - - •••• - ----- 7
Installing Exterior Earphone/Microphone -- --- - --- - --- -·7
Getting Acquainted-------... - ...-------. -. - - - -. -. - 8.11
LED Screen •-. - --------- - - - -•-. - - - --- - - ••_. - - -- - 11
Basic Operation -----------------.•_.-•. ---------. 12, 16
Power ON/OFF - - - •- - ••• -.- •• -------- -.- - - - - - - •• -.- 12
Volume Control-·-•••••------ - -- - - - - --. _.-.- _••• - - - 12
Choose Displaying Mode-- _••• - - -----.-- - -- - ---- - - 12
Choose Channel----- _••--. - - - ----------------_.- - 13
Choose Frequency ------------ ••• - ••• -------------13
Squelch - -- -- - •-.----••••-._••---- - - -.-••• - •-.-- - -14
Transmitting' ------- ----- - -- - - - -.-. - ----- -- -.-- - - - 15
Receiving ----- - -- - - - - -.--_••••------.------ - - - - - - 15
High/Low Power - -- _. - -------------- - -.-• - _••_. - - - 16
Advanced Operation -----------------------------1728
Add Scanning Channel·· - -_•• - - -------. - -------. -•.' 17
ChannelScanning _. -. _. - -- - - -. - ---- -. _••---. -••- -.17

.CONTENT
Frequency Scanning -.-----------------. - - - ----. - - 18
DTMF Calling ---- ••-------.------ •••• -----.-.- 19,21
Key Locked - - •------ •-•- -- - - - ••---- - -- • - - -----••-21
Lightening-- - ----- •• -- - --•• - ----•••••- - --- - •• --- - 21
ReverseFrequency----•-. - •- - - - - •••--••--••------.22
Stepping.-.------••• ------.------•• --------.----- 22
VOX--.----- •••-. - ---- - •• - -- --••• -- - -. -.-.-- - - - - 23
CTCSS/DCS-••-----.-.---. -. -.-.-----. --- - - -.23, 25
SlipFrequency. - - ---.- - - - -•• - -. - ---•••------••- - -. 25
Wide/Narrow Band - - -.-•• -. - - - - -.------- •• - -- - - - •• 26
Copy Channel- - ----. ----- -.-.--- - - - -•• ------.- - --26
SaveChannel--••• -.--- -. - ------.-.---- - ---------.27
Delete Channel -. -.--•-••-------.---- - - - -. ----•• -. 27
Copy Function with Cable - -. - -----•• ---- - -•••------28
Auxiliary Operation---. -------•.-------. -------. 29,31
Time-out Timer - -- - - - ••- - -.--.-••• -----••----.-. - •. 29
TOT Pre-cautionTime---- - - - --- - - - -. -.- - --. -. --- - -.29
Intervalafter TOT---- • -- -. --••••• - - - - - -. - - - - -. - --- 29
TOT ResumeTime··------. -.-- - ---- - - - - •• - ••- - - -. 29
MONI KeySetting ------.-.-------.----- ••-------.-29
Busy ChannelLokced•-------_. - - -----.--- - - -.---- 30
Battery Save - - -••••• ----- • - - - - -- - --------••-- - • - -.30
Prompting Voice - - - - •••-------••• - -- ---.-----•-. - -.30
Low BatteryWarning -.- - ----••• -----.-•• - - - --••- - - - 30
PTT 10 -. - - - ----.------ ----.-- -- .:- - - --.-.-. ----. - 31
Input Information ---- -. - - - --••• -. ----•• - - - --- -.-- - -. 31
Main Technology Parameter··------·-------·--- 32,33
Trouble Shooting -•.•• -----•.• ---- •. -.•--- .• --- 34, 35
Carefully unpack the transceiver.We suggestthat youconfirm the
itemslisted in thefollowingtable beforediscarding the packing
material.If any items aremissing orhave beendamaged during
shipment,contact with the dealerimmediately.
ITEM
QUA JTiiY?0) l;h
136-174MHz
Antenna 350-390MHz1
400-470MHzetc.
Li·ionBattery Charger1
Adaptor 1
Li-ion Battery (7.4V 1100mAh) 1
Gallus1
Belt Clip 1
Screws 1
Instruction Manual1

BATTERY
Please charge the battery before you use it,because it was uncharged
against delivery. The first charging after purchasing or keeping for more
than2months without usingcannot achieve normalbattery capacity.
Afterrepeating the charge/discharge for 2or 3times, the battery can get
to the best performance Please change or charge the battery if low power.
1.Please use the specific charger,other models may cause explosion
andlead to hurt the body.
2. Do notshort circuit the battery or put itinto fire,nor remove the housing
of the battery.
3. The ambient temperature should between 5C and 40 C while charging.
Otherwise, it may not fUlly charge.
4.Power OFF the transceiver with battery while charging. Using the devic
while charging would affect normalcharging.
5.Toavoid interfering the charging, please do not cut off the power or take
out the battery during charging.
6. The battery life will over soon when its operating time decreases even
though itis fully andcorrectly charged.Please replace the battery.
7.Please do not take out the battery and recharge it after it was fully
charged,otherwise the battery would be damaged or the life would be
shorten.
8.Please do not charge when the battery or the transceiver is damped.
Do it before wipe it up to avoid the hazard.
o
Instruction
Manual
~~~
Headset Speaker/Mic Speaker/Mic
(QME-01) (QME-02)
~~
®~
~
~
\ .'/
Programming Programming Copy Cable
Software Cable (QXPL-01)
~
ST-6.5-150V-1 ST-8.5-400V-1
~
ST-8.5-150V-2 ST-10-400V-2
Alwarningl
Whenjewelry, keys or ornamental chain and otherelectricmetals contact
withthe battery terminal, the battery may cause damage or hurt bodies.
If the battery terminal short circuit it wi generate a lot of heat,Please be
careful when you bring or use the battery,especially put it into the pocket,
purse or other metalcontainer.

HOW TO CHARGE
1.Plug the AC adaptor into the AC outlet,then plug the cable of
adaptor intothesocket at theback of charger.The charger
indicator on GREEN.
2.Plug the Li-ion battery pack or transceiver wifh a Li-ionbattery
packinto the charger.
a.Make surethebattery is connected with the charging terminal.
b.TheindicatorlightsRED while charging.
3.When it is 90% charged(about 4 hours),the indicator turns to
LIGHTGREEN (and need to be charged for2 hours more) ..
4.Theindicator turns to GREEN whilefully charged.
•After charging the supplied batteryfor 6 hours,remove it or transceiver
equipped with thebatteryfrom the charger. Please do not chargefor
over 10 hours,nor place it in charger for recharging.Over-charging will
shorten thelife of the battery andaffect its performance .
•Please payattention to thelocal netpower,in order to supply different
adaptors.
How to Store
1.lf the batteryneeds tobestored,itshouldkeepinthe statusof 50%charged.
2.ltshould be keep inlow temperature,dry environment.
3.Keep it far away from heating places,included the place where
the sunshine istoo strong.
INSTALLIN THE ACCESSORIES
•Do not shori circuit the battery and put battery into fire.
•Donot try to remove the housing of battery pack.
•Do not install batteryin the dangerous circumstance,;tmay
cause explosion.
•Donot place them in high temperature place or put it intofire,
in case of explosion.
Removing the Battery:
2.Press the release latch and
slide the packaway from the
transceiver.
Thetransceiver performs bestwhen the Li-ionbattery pack is
fully charged,especiallyfor long-time transmitting orcontinuo-
uslyuse.

INSTALLING THE ACCESSORIES INSTALLING THE ACCESSORIES
CD mtlDt::r:D
CD •••• em
•••• _a:t
CD _cu:>cm
Installing the Antenna:
Screw the antenna into theconnectoron
the top ofthe transceiver andturn clock-
wise to fastenit.
Removing the Antenna:
Turn the antenna counterclockwise to
remove it.
Plug the gallusintothering on the right
side of the transceiver,and put the other
side of thegallus intothe ring, and then
fasten it.
Installing the Belt Clip:
Aim the screweyes of belt clip and
the AI.shell of transceiver at each
other,thenfasten the belt clip with
the screws.
Removingthe Belt Clip:
When remove the belt c1ip,fastening
its fixedscrews.
Unveil(not needto take itout)the cover of
J
the MIC-SP jack,then plug the earphonel
"Mic into the jack of earphone/MicWhen
iO .
uSing earphone/Mic,it willaffect theperf-
ormance ofwaterproof.
~@

GETTING ACQUAINTED GETTING ACQUAINTED
1.Power SwitchNolume Control
Turn clockwise to power ON and adjust volume while turn
counterclockwise to power OFF.
2. LED Indicator
Lights RED while transmitting,lights KELLY while receiving,
flashes RED while in low battery.
3. Circumrotate Encoder
Rotate to select channels, and also workwith other function
keys to set functions.
4.[PTT] Switch
Press,then speak into the microphone to transmit, and also
work with other function keys to set functions.
5. [MONI] Key
According to how to program auxiliary functions of this key.
Please refer to P30 of the details instruction,press ON/OFF
the programmable auxiliary function,and alsoworkwith other
function keys to set functions.
6. [DIAL] Key
Use to store/confirm/transmitldelete DTMF number,also using
as a functionkey.
7.[FUNC] Key
Function key,press to unlock other functions setting.

GETTING ACQUAINTED GETTING ACQUAINTED
8.[SCAN] Key
Press to begin or stop scanning,and also work with other
function keys to set functions.
13 DCS " """ " i,
75100
+ ACT C,C, C•.O O.C · ~gl .I
-lllil •••• vox~ R
9.[LOW] Key
Press to choose transmitting in High/Low power,andalso
work with other function keys to set functions.
ICON INSTRUCTION
-
Displayswhen monitoring thechannels
(Squelch ON)
Dsiplayswhen the selected channels are
A
in the scan list while displays nothing
when the channelis out ofscan list.
CI CI CI C CI CI
Displays the working frequency or
channel number.Select different functions
tI .I LU" Lf..I displays different numbers.
IBB
Displays all kinds of numbers as per
selected functions.
R
Displays when the ReverseFrequency
function is ON
VOX
Displays when VOXfunctionis ON.
While receiving, itmeans signal strength
..... _---
(the more,the stronger),while transmitting,
it means power(the more,the higher).
[i
DisplayswhenpressingFUNCtosetthefunctions
II ]
Displays when transmitting in low power.
+Displayswhen Key Locked functionis ON.
A Displays whenusing narrow band.
CT Displays when CTCSS function isON.
DCSDisplays whenDCS functionis ON.
a
Displays whenselling Slip Frequency function.
75
50
Mantissa of frequency.
.25
10. [DTMF] Keypad
Use tostore and transmit DTMF number,and also work with
otherfunction keys to set functions.
11. MIC-SP Jack
Connect earphone/microphone bought by users.

BA iIC OPERATION
Power ON/OFF
Turn [Power SwitchNolume Control] clockwise to power ON the
transceiver.
Turn [Power SwitchNolume Control] counterclockwise to power
OFF the transceiver.
Volume Control
Rotate [Power SwitchNolume Control] to adjust volume.Turn
clockwise to turn up thevolume while turn counterclockwise
to turn down.When adjusting the volume, pressMaN I to mo-
nitor the background noise.
•When communicating with others,you need to adjust the
volume correctly.
Choose Displaying Mode
There are 3 kinds of displaying modes for free choice.
Channel Mode
Press DIAL for 1 second (the prompting voice would be heard
if set)," Iii" flashes on the screen,then press Law.
•The current channeldisplays on the screen.
Frequency+ChannelMode
Press DIAL for 1 second,and then press again.
•The current communicating frequency and channel displays
on the screen.
Frequency Mode
Press DIAL for 1 second,and then press SCAN.
•The current communicating frequency displays on the screen.
BA iIC OPERATION
•Channel modedisplays UNPG ifany channel hasn't been
programmed.You can only press DIAL to change to frequency
mode.
Choose Channel
Thisfunction is validunder the display mode of Channel and
Frequency+ChanneI.Rotate[CircumrotateEncoder] to choose
needed channel.Turn clockwise toincrease the channel num-
ber whileturn counterclockwise to decrease it.
•When theprogrammed frequency of chose channel is out of
therange of transceiver, it will alert youout of lock.
•The screen displays chose channels.
Choose Frequency
This function is valid only under the displaymodeofFrequency.
There are 2 ways for free choice.
1.Input frequency
Rotate [Circumrotate Encoder] to choose frequency,turn clo-
ckwise according "stepping" to increase frequency whileturn
counterclockwise to decreaseit.
•The selected frequency displays on the screen.
•Pleaseselect the stepping before circumrotateencoderto
choose frequency (Refer to P22 of "STEPPING'?

BA iIC OPERATION
2. Input frequency on Keypad
•Press[DTMF],then input the frequencydirectly.
E.g.linput 4,0,3,0,5,0 when communicating in 403,050MHz,
hescreen displays 403,050,thatmeans you can communi-
cate in 403,050MHz.
NOTE:Input frequency onkeypadis related to stepping,use
CircumrotateEncoder to select and adjustfrequency.
•Theinputfrequency displays on the screen.
•Wheninputting wrong frequency,press [MON/} to cancel.
•Frequency rangeandstepping frequency of transceiverwould
restrict the frequencyyou inputPlease pay moreattention
aboutthe stepping youset.
Squelch
When there is no signal,squelch function can mute loudspeaker.
Whensquelch function is ON,you will hear the background noise
from the loudspeaker,while thesquelch is OFF you will not hear
the background noise.The squelchlevel youchoose willdecide
when yoursquelch is ON/OFF. If thelevel is too high,you cannot
get weak signal,if thelevel is too low,thesignal will appears in
the background noise.
How to Adjust Squelch
1.PressFUNC for 1 second, then pressLaw.
•The screen displays"_SqL" and the current squelch level.
BA iIC OPERATION
2. Turn the encoder from O(open)to9(tightest) to select the
squelchlevel.
•Turn clockwise to increase the squelchlevel,turncounter-
clockwise to decrease the squelchlevel.
3. Press any key to end the setting.
•Return to normaloperation.
Transmitting
According to different settingsfor the monitor function,press
MaNIto monitor the loudspeaker for a moment,and confirm
there isno broadcasting station is transmitting on theselected
channel.Press PTT, andthen speak into themicrophone.
1. Please keep themicrophone approximately 3-4cm from
yourmouth,and speakin normalspeaking voice to ensure
best performance.
2. When pressing PTT, LED lights RED.
3. Release PTT toreceive.
Receiving
If the working channel is called, LED lightsGreen,you can
receive the call.
•If the signal is weakand you have set the higher squelch
level,you maymiss the call.
•Localdealermay program the CTCSS/DCS.You could only
receive calling from the station thatselected the same
CTCSS/DCS as yours. Othercallings cannot be heard.

BA§IC OPERATION ADVANCED OPERATION
High/Low Power
For tansmitting in high power,large waste in battery,thus it dose
not need high power in short distance communication,we can
choose low powerto save battery, while we use high power
when in long distance communication.Press LOW to choose
High/Low power.
•Low power,displays "LO" on the screen while high power
displays nothing.
Add Scanning Channel
This function is valid only under thedisplay mode of Channel
and Frequency+Channel.You can choose channels for scanning.
1. Rotate [Circumrotate Encoder] to choose add scanning cha-
nnels.
2. Press FUNC for 1 second to set the function ON.
•"F" flashes on the screen .
3.Press SCAN to add/cancel the added scanning channels.
•The channel displays "A" onthe screen while it is added
toscan.
•The channeldisplays nothing whileitis not added to scan.
Repeat the above operation,channel will alternate between
scan and non-scan.
Channel Scanning
This function is valid onlyunder the display mode of Channel
and Frequency+Channel, which is used to monitor every added
scanning channel of the transceiver. When scanning, the trans-
ceiver will check every channeland only stop in the channel
withsignal.

ADVANCED OPERATION
1.Press SCAN to begin scanning.
•Scan starts from current channel,and channel number
increases gradually.Screen displays "SCAN".
• The transceiver will stay in the communicating channel until
thesignaldisappears. Scan will returnafter signaldisapp-
ears for 4seconds, unless there is new signal appears
within these 4 seconds.
2.Press any key except MONI to end scanning.
Frequency Scanning
This function is valid only under the display mode of Frequency.
It is used to monitor the signalin every frequency of the step-
ping.When scanning,transceiver will checkthe increased step-
ping and only stop in the frequency with signal.
1. Press SCAN to beginscanning.
•Scan starts from current frequency,andincreases according
to the stepping.
•Screen displays "SCAN"
When theincreased frequency range isout of transceiver frequency,
itwill turn to the lowest frequency to increase as per "stepping".
The transceiver will stay in the communicating frequency until
the signaldisappears. Scan willreturn after signal disappears
for 4 seconds,unless there is new signal appears within these
4seconds.
•When scan quitin a specificfrequency,the screen displays
frequency rate,the dot between frequency will flash on the
screen.
2.Press any key except MONI to end scanning.
ADVANCED OPERATION
DTMF Calling
Manually Dialing
Press PTT,and then enter the needed numbers.
•Press PIT,thenenter the first digit you input,release PIT,
and then release the digits keypad,the transceiverwillkeep
transmitting within 2 seconds,you need not keep pressing
PTTto dial.
•When transmitting DTMF,microphonewill be muted,you can
monitor the double-audio-frequency through loudspeaker.
Automatically Dialing
Dial Saved DTMF Numbers
Dialsaved DTMF number of thememory number units.
1.Press DIAL toenter the dial-up mode.
•Screen displays "__ d"
2.Input the dialed memory number units (1-9)
•Screendisplays andscrolls thecalling numbers and
sounds DTMF.
3. Return to theformer display automatically.
Redial DTMF Numbers
Redial the last transmitted DTMF number(16digits max.)
1.Press DIAL toenterthe dial-up mode.
•Screen displays "__ d"
2. Press [0]to dialthelast transmitted number.
•Screen displays and scrolls the calling numbers and
sounds DTMF.
3. Return to the former displayautimatically.

ADVAI\ICED OPERATION
Save DTMF Numbers
1. Press DIAL to enter the dial-up mode.
•Screen displays "__ d"
2. Press [#]to enter the store mode.
3.Enter the numbers in the DTMF keypad.
•If you inputincorrect number, press -MaN I to clear it and
enter the correct one.
4.Press DIAL after input the digits,and then enter digits of the
memory channel numbers (0-9).
•Return to the former display.
Confirm Saved DTMF Numbers
Check the memory channel number units.
1. Press DIAL to dial-up mode.
•Screen displays "__d"
2. Press [*] to enterconfirmed saved mode.
3.Enter the needed memory number units (1-9)
•Screen displays and scrolls the saved DTMF numbers
and sounds correspongding DTMF.
4. Return to the former display automatically.
Delete Saved DTMF Numbers
Delete the memory channel number units.
1. Press DIAL to enter thedial-up mode .
•Screen displays "__ d"
2.Press [0] to enter the delete mode .
•Screendisplays "c1r_d"
Press any key except digit keys from 1 to 9 tocancel the
operation.
ADVANCED OPERATION
3. Input the needed delete DTMF numbers (1-9).
•The selected DTMF numbers were deleted.
4. Return to the formerdisplayautomatically.
Key Locked
This function is to avoid operating transceiver incorrectly,to lock
keypad of the transceiver.
1. Press FUNC for 1 second,the function is ON.
•"Iii"flashes on the screen.
2. Press [*] to enter Key Locked.
•"+" displays on the screen.
•When key locked function is ON, allthe keys are invalid
except PTT,MONI,FUNC.
To unlock keypadof thetransceiver, please repeatthe above operation.
Lightening
You can setthelightening function to beautomatism, connec-
tion or off.
1. Press FUNC for 1 second,the function is ON.
•"Iii"flashes on the screen.
2. Press [2] to select lightening function.
3. Rotate [Circumrotate Encoder] to select the needed setting.
•Displays "A" for automatism. The light onscreenwill light
for 5 seconds when press any key except PTTand MONI,
and then putout automatically.
•Displays "ON" for connection. The light on screen will light
when the transceiver is power ON.
•Displays "OFF" forcutting off.The light on screen will not work.
4. Press any key to end setting,and return to the formerdisplay.

ADVANCED ,OPERATION
Reverse Frequency
Transmitting and receiving frequency will reverse whenusing
the reverse frequencyfunction.Itmeans to transmit withreceiv-
ing frequency, to receivewith transmitting frequency.If set CTCS
SIDCS function,encoding and decodingsignalwill also reverse.
1. Press FUNC for 1 second,the function is ON.
•"F" flashes on the screen.
2. Press [3] to set reverse frequency function ON.
•Screen displays "R"
While changingchannel/frequency or scanning,the reverse
frequency function is OFF.
3.Repeat the above operation,thechannel will alternate
between ON/OFF reverse frequency.
Stepping
This function is valid only underthe mode of fullrange of Fre-
quency. Setting setpping would restrict the transceiver choos-
ing frequency and frequency scanning.
1.Press FUNCfor 1 second,thefunction is ON.
•[ii flashes on the screen.
2.Press [#] to select stepping frequency.
•Screen displays the current stepping frequency.
3. Press LOW to choose steppingfrequency in circle.
5 means stepping is5KHz
6.25 means steppingis 6025KHz
12.50means stepping is 12.50KHz
25 means stepping is25KHz
50 means stepping is50KHz
1.000means steppingis 1.000KHz
10.000 means steppingis 10.000KHz
4.Press other key to end setting,and return to the former display.
ADVAI\ICED OPERATION
VOX
This transmitting function can communicate hands-freely.When
using VOX, if microphone's gain ishigher than VOX gain,
the transceiver will turn to transmittingmode automatically while
returntoreceiving mode after 2 secends ifmicrophone'sgain is
lowerthan VOX gain.Owingto switching between transmitting
and receiving,wesuggest not transmit whensetting VOX gain if
the surrounding is too noisy.
1.Press FUNC for 1 second, the function is ON.
•"F" flashes on thescreen.
2. Press [1] to enter VOXfunction.
•"VOX" flashes on the screen,at the same timethetopright
corner of the screen displays the current VOX transmitting
gain.
3. Rotate [Circumrotate Encoder] to select the VOX transmitting
gain from "OF" to "3".
•Turn clockwise to increase VOX transmittinggain while turn
counterclockwise to decrease it.
•Screen displays "OF" when VOX is OFF."1" means low gain,
"2" means middle gain,"3"means high gain.
4.Press any key to end setting.
•Screen displays "VOX" when select the gain from 1 to 3 and
displays nothing when VOX function is OFF.
CTCSS/DCS
When the channel setting CTCSS/DCS code,the squelch func-
tion ON onlyreceived the corresponding CTCSS/DCScode.
And, the transceiver which has the same CTCSS/DCS code
can receive the signal you transmit.

ADVAI\ICED OPERATIOI\I
• Program CTCSS/DCS code in your transceiver can help
you to ignore (not hear)some unnecessary callings from
ther transceiver. But that not means your calling is privacy.
Adjust Receiving CTCSS/DCS Decode
1. Press FUNC for 1 second,the function is ON.
•"F" flashes on the screen.
2. Press [A) to adjust receiving CTCSS/DCS decode.
•Screen displays the current code.
3. Press LOW to select the mode of CTCSS/DCS/OFF in circle.
•Displays "q" before the digits when select CTCSS code,
displays "d" before the digits when select DCS code, select
"OFF" to delete.
•WhenselectDCS code, press DIAL to choose Normalor
Inverted code.Inverted code displays" - "while Normal
code displaysnothing.
4.Rotate [Circumrotate Encoder] to select new CTCSS/DCS
code.
5. Press any key except PTT and MONI to exit and store the
adjusted code.
•Set CTCSS decode,screen displays "CT"while receiving.
Set DCS decode, screen displays "DCS" while receiving.
Set OFF,screen displays nothing.
Adjust Transmitting CTCSS/DCS Encode
1. Press FUNC for 1second,the function is ON.
•"~ "flashes on the screen.
2. Press [B) to adjust receiving CTCSS/DCS encode.
•Screen displays the current code.
ADVAI\ICED OPERATIOI\I
3. Press LOW to select the mode ofCTCSS/DCS/OFF in circle.
•Displays "q" before the digitswhen select CTCSS code,
displays "d"before the digits when select DCS code, select
"OFF" to delete.
•When select DCS code, press DIALto choose Normal or
Inverted code. Inverted code displays" - " while Normal
code displays nothing.
4. Rotate [Circumrotate Encoder) to select new CTCSS/DCS code.
5.Press any key except PTT and MONI to exit and store the
adjusted code.
•Set CTCSS decode,screen displays "CT" while transmitting.
Set DCS decode,screen displays "DCS" while transmitting.
Set OFF,screen displays nothing.
Slip Frequency
This function is valid only under the display mode of Frequency,
setting the slip frequency of receiving and transmitting it.
1. Press FUNC for 1 second, the function is ON.
•"~" flashes on the screen.
2. Press [0) to set slip frequency.
•Screen displays the current slip frequency status.
3.Press SCAN to select +/- slip frequency.
•"13" displays before the frequency when it is - slip frequ-
ency, while + slip frequency displays nothing.
4.Rotate [Circum rotate Encoder) to increase/decrease slip
frequency as per the stepping.
•Screen displays slip frequency.
5. Press other key to exit and store the setting.

ADVANCED OPERATION
Wide/Narrow Band
The user can set transceiver to communicate in wide/narrow
band freely according to different countries.
Highvolumebut bigdistortion when the transceiver with wide band
talk to the transceiver with narrow band,and squelch switches OFF
as theincreasing ofvolume.Low volume but largenoise when the
transceiver with narrow band talk to the transceiver with wide band.
1. Press FUNC for 1 second to setthe function ON.
•1:iI "flashes on the screen.
2.Press [4] toselect Wide/Narrow band.
•Narrowband displays" .•." on the screen while wide band
displays nothing.
Repeatthe above operation to choose Wide/Narrowband in circle.
CopyChannel
This functionis valid only under the display mode of Channel
and Frequency+Channel.Copy one channeldata of the
tranceiver to otherchannel.
1. Select the needed copy channel.
2.Press FUNC for1 second to setthefunction ON.
•" I:iI "flasheson the screen.
3. Press [C]to select the saved copychannel.
•Screendisplays the saved channel.
4.Rotate [Circumrotate Encoder] to select the channel.
•Press any key except [PTT] to exit but not store.
5.Press PTTto store and exit.
•Now theinitial channeldata isthesame with savedchannel data
ADVANCED OPERATION
Save Channel
This function is valid only under the display mode of Frequency.
Program receiver channel when the transceiverwithout any ext-
erior equipment.
1. Enter the Frequency mode.Select the frequency,slip freque-
ncy,encode/decode signal,etc.
2. Press FUNC to set the function ON.
•1:iI "flashes on the screen.
3. Press [C]to select the saved channel.
•Screen displays the saved channel.
4. Rotate [Circumrotate Encoder]to select the saved channel.
•Press any key except PTT to exit but not store .
5. Press PTT to storeand exit.
•The programmeddata under full range ofFrequency mode
was stored in the saved channel.
Delete Channel
Delete the programmedchannel data of thetransceiver.
1. Press FUNC for 1 second, the function is ON.
•1:iI flashes on the screen.
2. Press [0] to select the deleted channel.
•Screen displays the deletedchannel.
3. Rotate [Circumrotate Encoder] to select the needed delete
channel.
•Press any key except PTT to exit but not store.
4. Press PTT to store and exit.
•This channeldata was deleted and never displays besides
you reprogrammed it.

ADVANCED OPERATION
Copy Function with Cable
Copy function with cableis that copying the data from a trans-
ceiver to another transceiver without any exterior equipment.
•This function isON only when thelocal distributor set
it for you.
1.Power off the main transceiver.Press [LOW] and [MONI] at
thesame time to poweron and enterinto the copying status.
The screen displays "COPY".
2.Repeat STEP 1 for the targettransceiver. The screen displays
"COpy" too.
3.Connect the two transceivers with specified copying cable.
4.Press [FUNC] of the main transceiver to begin to copy. The
screen displays "COPY-t",sending its data tothe target
transceiver.
S.The two transceivers display "COpy" whenfinishing the
copyingand back to copying stand-by status.If itis needed
to copy to another target transceiver,the target transceiver
should enterinto copying status first, and then repeat STEP
3 and STEP 4. Repeat the operations for multi-transceivers.
6.Restart the poweragain whenfinishingcopying,and the
machine willback to normalworking status.
• When in stand-bystatus,displays COPY.
• Whenin receiving status,displays COPY-r.
• When in transmitting status,displays COPY-I.
AUXILIARY OPERATION
Adopt OXPG-78D(Software) and OXPG-01
(Program cable)to program.
Time-Out Timer
The purpose of the Time-out timer is to prevent any single
person from using a channelfor an extended period of time.If
you continuously transmit more than limited time, the transceiver
will stop transmittingand an alert tone will sound.To stop the
tone,release PIT.
•Pre-cautionbefore TOT:The alert tone sounds before the
limited TOT time of the transceiver.
•IntervalafterTOT:It isinterval after limited TOTtime you
have set.You cannot transmit during this interval.
•TOT resume time: Pre-setTOTresume time,when this
function is on,you can not transmit before TOT resume time.
Only when resume time arrives,then can transmitagain.
[MONI] Key Setting
MONI key can be set as thefollowing auxiliary functions.
•Squelch OFF Default setting)
Press tohearthe background noise,release to return the
normaloperation. It is used to get the weak signal which you
can't get even operated correctly.
•None No function)
No operation if press.
•Activate Monitor
Press to set CTCSS/DCS OFF,press again to return normal
.operation.