Zotac IONITX-E series User manual

1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
Electronic Emission Notices
WARNING!

2
IONITX Synergy Series Motherboard
Table of Contents
Motherboard Specifications ------------------------------------------------------------------- 4
Motherboard Layout------------------------------------------------------------------------------ 6
Hardware Installation ---------------------------------------------------------------------------- 8
Safety Instructions ----------------------------------------------------------------------------- 8
Preparing the Motherboard -------------------------------------------------------------------- 9
Installing Memory DIMMs -------------------------------------------------------------------- 9
Installing the Motherboard ------------------------------------------------------------------- 10
Installing the I/O Shield ----------------------------------------------------------------------- 10
Connecting Cables and Setting Switches ------------------------------------------------ 11
20-pin ATX Power Connector-PW1-------------------------------------------------------- 12
Front Audio Header-FP_S1------------------------------------------------------------------ 12
COM Header-CN2 ----------------------------------------------------------------------------- 13
Speaker Header-SPK ------------------------------------------------------------------------- 13
USB Headers-FP_U1~FP_U2 -------------------------------------------------------------- 13
Front Panel Header-FP1 --------------------------------------------------------------------- 14
Serial-ATA (SATA) Connectors-------------------------------------------------------------- 15
Fan Connectors -------------------------------------------------------------------------------- 15
Expansion Slots -------------------------------------------------------------------------------- 16
Mini PCIE Slot ------------------------------------------------------------------------------ 16
PCI Express x1 slots-PCIE1(Optional)----------------------------------------------- 16
Jumper Settings -------------------------------------------------------------------------------- 16
Configuring the BIOS ---------------------------------------------------------------------------- 17
Enter BIOS Setup----------------------------------------------------------------------------------- 17
Main Menu -------------------------------------------------------------------------------------- 18
Advanced Menu------------------------------------------------------------------------------- 18
CPU Configuration------------------------------------------------------------------------- 18
IDE Configuration -------------------------------------------------------------------------- 19
Floppy Configuration ---------------------------------------------------------------------- 19
ACPI Configuration ------------------------------------------------------------------------ 19
APM Configuration------------------------------------------------------------------------- 19
Event Log Configuration----------------------------------------------------------------- 19
MPS Configuration ------------------------------------------------------------------------ 19
PCI Express Configuration -------------------------------------------------------------- 19
Smbios Configuration --------------------------------------------------------------------- 19
USB Configuration------------------------------------------------------------------------- 19
PCI/PnP Menu --------------------------------------------------------------------------------- 20
Boot Menu -------------------------------------------------------------------------------------- 21
Security Menu --------------------------------------------------------------------------------- 22
Chipset Menu---------------------------------------------------------------------------------- 23
Exit Menu --------------------------------------------------------------------------------------- 23

3
Table of Contents
Installing Drivers and Software -------------------------------------------------------------- 25
Drivers Installation ------------------------------------------------------------------------------- 26
HDMI SETUP --------------------------------------------------------------------------------------- 33
REALTEK HD AUDIO DRIVER SETUP ----------------------------------------------------- 34
Getting Started---------------------------------------------------------------------------------- 34
Sound Effect------------------------------------------------------------------------------------- 34
Environment Simulation ---------------------------------------------------------------------- 34
Equalizer Selection --------------------------------------------------------------------------- 35
Frequently Used Equalizer Setting -------------------------------------------------------- 35
Karaoke Mode ---------------------------------------------------------------------------------- 35
Mixer----------------------------------------------------------------------------------------------- 36
Playback control --------------------------------------------------------------------------- 36
Recording control-------------------------------------------------------------------------- 37
Audio I/O------------------------------------------------------------------------------------- 38
Speaker Configuration ------------------------------------------------------------------- 39
Connector Settings------------------------------------------------------------------------ 40
S/PDIF --------------------------------------------------------------------------------------- 40
Speaker Calibration----------------------------------------------------------------------- 41
Microphone---------------------------------------------------------------------------------- 42
Noise Suppression ------------------------------------------------------------------------ 42
Beam Forming ----------------------------------------------------------------------------- 42
Acoustic Echo Cancellation------------------------------------------------------------- 42
Audio Demo--------------------------------------------------------------------------------- 43
Information --------------------------------------------------------------------------------- 43
SATA RAID User Manual ------------------------------------------------------------------------ 44
Setting up the BIOS --------------------------------------------------------------------------- 44
Entering the RAID BIOS Setup ------------------------------------------------------------- 45
Installing the RAID Drives-------------------------------------------------------------------- 46

4
IONITX Synergy Series Motherboard
Motherboard Specications
qChipset
v NVIDIA MCP7A-ION Series
qSize
v Mini-ITX form factor of 6.69inch x 6.69 inch(171mm x 171mm)
qMicroprocessor support
v Intel ATOM 230 / 330 CPU
v Support for 533 MT/s(133MHz FSB)
qOperating systems:
v Supports Windows XP 32bit/64bit and Windows Vista 32bit/64bit
qSystem Memory support
v Supports DDRII667/800. Supports up to 4GBs DDRII memory.
v Supports dual Channel DDR2 128-Bit Memory Interface
qUSB 2.0 Ports
v Supports hot plug and play
v Ten USB 2.0 ports (six rear panel ports, four from onboard USB headers)
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
qOnboard Serial ATA II
v Independent DMA operation on four ports
vData transfer rates of 3Gb/s.
qOn board RTL8211CL Gigabit LAN(Optional)
v Supports 10/100/1000M bps operation
qOn board RTL8201EL Fast Ethernet(Optional)
v Supports 10/100Mbps operation
v Supports half/full duplex operation
qOnboard Audio(Optional)
v Azalia High-Definition audio
v Supports 6-channel
v Supports Jack-Sensing function
qGreen Function
v Supports ACPI (Advanced Configuration and Power Interface)
v RTC timer to power-on the system
v AC power failure recovery
qOnboard Graphics support
v Integrated 300MHz DAC for analog displays with resolutions up to 1920x1440
at 75Hz.
v Integrated GeForce 9xxx Series GPU,Supports DX10
v VGA / DVI / HDMI output support(optional)

5
Motherboard Specifications
qIntegrated HDMI Interface with HDCP
v Supports DVI or HDMI 1.3 interfaces
v Secure digital audio merged from integrated HDA codec with no external audio
signals required
v Support for HDCP 1.3 using soft or hard HDCP keys
v HDCP encryption support when configured as DVI or HDMI link without the
need for external HDCP key crypto ROM
qDual Head Display Controller
v Full NVIDIA nView™ multi-display technology capability, with independent
display controllers for the CRT, TMDS, DisplayPort, and HDMI interface
v Each controller can drive same or different display contents to different resolu-
tions and refresh rates
qExpansion Slots
v One Mini PCI Express slot.(Occupied by WiFi module in some models)
v One PCI Express x1 slot

6
IONITX Synergy Series Motherboard
Motherboard Layout
Figure 1 shows the motherboard and Figure 2 shows the back panel connectors.
Figure 1. Board Layout
120 240
121
120 240
121
+
R
. ..
SPDIF-OUT
CPU
4
5
6
7
98
2
3
11 10
12
13 14 15 16 17 18
CN1
CN11
U_L AN
SD1
FP_S1
J2505
JP1
SATA1 SATA4
CN2
Chiset
FP_U2
FP_U1
C_FAN1
DDRII1 DDRII2 PW1
S_FAN1FP1
SPK1
Mini PCIE
2 52
51
SATA2 SATA3
FJ5
JP3
PCIE1
USB_1
DVI/VGA
20-pin ATX Power Connector-PW1
System Fan Connector-S_FAN
Front Panel Header-FP1
Speaker Header-SPK
Chip Fan Connector-J2505
Serial-ATA (SATA) Connectors
BIOS Selection Jumper-JP3(Optional)
COM Header-CN2
PCI Express x1-PCIE1(Optional)
1.
2.
3.
4.
5.
6.
7.
8.
9.
USB Headers-FP_U1~FP_U2
Front Audio Header-FP_S1
Backpanel Connectors
Mini PCIE Slot
CPU
Chipset
Clear CMOS Jumper-JP1
CPU Fan Connector-C_FAN
DDRII DIMM Sockets
10.
11.
12.
13.
14.
15.
16.
17.
18.

7
Rear Panel
6.Port 2-Channel 4-Channel 6-Channel
Blue Line-In Rear Speaker Out Rear Speaker Out
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Center/Subwoofer
7. WiFi antenna connctor(Optional)
Remove the red antenna connector cover(as picture 1), install the antenna to the connector
and make sure that screw down clockwise(as picture 2),at last as picture 3.
Figure 2: Backpanel connectors
2 2
35 6 7
6
11
5
10
15
4
8
9
120 240
121
120 240
121
+
R
. .
.
3
Note: According to your requirement modulate to the antenna
as right picture.



1
6
11
5
10
15


2
6
11
5
10
15


1. PS/2 keyboard connector
2. USB Connectors
3. HDMI Port
4. SPDIF Out(Coaxial/Optical)(Optional)
5. DVI Connector(Optical)
8. LAN Connector
Lan Port with LEDs to indicate status.
· Yellow/Light Up/Blink = 10 Mbps/Link/Activity
· Yellow and Orange/Light Up/Blink = 100 Mbps/link/Activity
· Yellow and Orange/Light Up/Blink = 1000 Mbps/link/Activity
9. VGA Port(Optical)

8
IONITX Synergy Series Motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics
covered in this section are:
q Preparing the motherboard
v Installing the memory
q Installing the motherboard
qConnecting cables and setting switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precations.
Remember to remove power from your computer by disconnecting the AC main source
before removing or installing any equipment from/to the computer chassis

9
Hardware Installation
120 240
121
120 240
121
+
R
.
.
.
DDRII-1
DDRII-2
Preparing the Motherboard
The motherboard shipped in the box does not contain a memory. You need to pur-
chase these to complete this installation.
Installing Memory DIMMs
Your new motherboard has two 1.8V 240-pin slots for DDR2 memory. These slots
support 256 MB, 512 Mb, 1GB / 2GB / 4GB DDR2 technologies. There must be at
least one memory bank populated to ensure normal operation. Use the following the
recommendations for installing memory. (See Figure 1 for the location of the memory
slots.)
q One DIMM: You can install the DIMM into any slot.
q Two DIMMs: Install into slots 1 and 2. The idea is to run on dual channel mode.

10
IONITX Synergy Series Motherboard
Use the following procedure to install memory DIMMs into the slots on the mother-
board. Note that there is only one gap near the center of the DIMM slot. This slot
matches the slot on the memory DIMM to ensure the component is installed prop-
erly.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into
the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock
the DIMM into the connector.
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis
you are using and if you are replacing an existing motherboard or working with an
empty chassis. Determine if it would be easier to make all the connections prior to this
step or to secure the motherboard and then make all the connections. It is normally
easier to secure the motherboard first.
Use the following procedure to install the I/O shield and secure the motherboard into
the chassis.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust and foreign objects, and
promotes correct airflow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis.
Press the I/O shield into place and make sure it fits securely. If the I/O shield does
not fit into the chassis, you would need to obtain the proper size from the chassis
supplier.

11
Hardware Installation
Connecting Cables and Setting Switches
This section takes you through all the connections and switch settings necessary on
the motherboard. This will include:
q Power Connections
v 20-pin ATX power-PW1
v Front Audio Header-FP_S1
q Internal Headers
v COM Header-CN2
v Speaker Header-SPK
v USB Headers-FP_U1~FP_U2
v Front panel header-FP1
q Serial ATA
q Chassis Fans
q Expansion slots
q Jumper settings
See Figure 1 to locate the connectors and jumpers referenced in the following
procedure.

12
IONITX Synergy Series Motherboard
20-pin ATX Power Connector-PW1
PW1 is the main power supply connector located along the edge of the board next to
the DIMM slots. Make sure that the power supply cable and pins are properly aligned
with the connector on the motherboard. Firmly plug the power supply cable into the
connector and make sure it is secure.
120 240
121
120 240
121
+
R
.
.
.
PW1-Pin Assignments
Pin Signal Pin Signal
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 GND 13 GND
4 +5V 14 PS_ON
5 GND 15 GND
6 +5V 16 GND
7 GND 17 GND
8 PWROK 18 -5V
9 +5V_AUX 19 +5V
10 +12V 20 +5V
Front Audio Header-FP_S1
The audio connector supports HD audio standard and provides two
kinds of audio output choices: the Front Audio, the Rear Audio. The
front Audio supports re-tasking function.
Note:
In order to utilize the front audio header, your chassis must have front audio connector.
Also please make sure the pin assignment on the cable is the same as the pin assignment
on the mainboard header. To find out if the chassis you are buying supports a front audio
connector, please contract your dealer.
FP_S1-Pin Definition
PIN Assignment PIN Assignment
1 MIC2(L) 6 Reserved
2 GND 7 FAVDIO-JD
3 MIC(R) 8 Key(No pin)
4 -ACZ-DET 9 Front Audio(L)
5 Front Audio(R) 10 Reserved
110
1120 PW1
2
1
10
9
FP_S1

13
Hardware Installation
120 240
121
120 240
121
+
R
.
.
.
Speaker Header-SPK
COM Header-CN2
CN2
1 2
9
10
USB Headers-FP_U1~FP_U2
This motherboard contains six USB 2.0
ports that are exposed on the rear panel
of the chassis(Figure 2). The motherboard
also contains two 10-pin internal header
connectors onboard.
1. Secure the bracket to either the front or
rear panel of your chassis (not all chassis
are equipped with the front panel option).
1 9
102
FP_U1
1
SPK
FP_U2
1 9
102
CN2-Pin Definition
PIN Assignment PIN Assignment
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND 10 NC
USB-Pin Definition
PIN Assignment PIN Assignment
1 VCC 6 USBP1+
2 VCC 7 GND
3 USBP0- 8 GND
4 USBP1- 9 KEY
5 USBP0+ 10 OC#
SPK-Pin Definition
PIN Assignment
1 VCC
2 NC
3 NC
4 SPK-

14
IONITX Synergy Series Motherboard
Front panel header-FP1
The front panel header on this motherboard is one connector used to connect the
following four cables :
q PWRLED
Attach the front panel power LED cable to these two pins of the connector. The
Power LED indicates the system’s status.
q PWR SW
Attach the power button cable from the case to these two pins. Pressing the
power button on the front panel turns the system on and off rather than using the
power supply button.
q HDD LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator
LED indicates the activity status of the hard disks.
q RST SW
Attach the Reset switch cable from the front panel of the case to these two pins.
The system restarts when the RESET switch is pressed.
Note:Some chassis do not have all four cables. Be sure to match the name on
the connectors to the corresponding pins.
FP1-Pin Definition
Pin Signal Pin Signal
1 HDD_LED+ 6 PWR_SW
2 PW_LED+ 7 RESET
3 HDD_LED- 8 GND
4 PW_LED- 9 NC
5 GND 10 KEY
120 240
121
120 240
121
+
R
.
.
.
FP1
1
2
9
10

15
Hardware Installation
120 240
121
120 240
121
+
R
.
..
Fan Connectors
There are three fan connections on the
motherboard. The fan speed can be
detected and viewed in the PC Health
Status section of the CMOS Setup.
CPU FAN Connector
GND
+12V
Sense
Control
CHIP FAN Connector
GND
5V
SYS FAN Connector
Sense
+12V
GND
1SATA -1 1
SATA -2
1SATA -4 1
SATA -3
SATA-Pin Definition
PIN Signal
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
Serial-ATA (SATA) Connectors
The Serial ATA II connector is used to connect the Serial ATA II device to the
motherboard. These connectors support the thin Serial ATA II cables for primary
storage devices. The current Serial ATA II interface allows up to 3Gb/s data transfer
rate.
There are four serial ATA II connectors on the motherboard that support AHCI and
RAID configurations.

16
IONITX Synergy Series Motherboard
Expansion slots
The NVIDIA MCP7A-ION motherboard provide two expansion slot as below:
Mini PCIE slot
There is one Mini PCI Express slot,reserved for WiFi Module.
PCI Express x1 Slots-PCIE1(optional)
There is one PCI Express x1 slot that is designed to accommodate less bandwidth-
intensive cards, such as a modem or LAN card. The x1 slot provides 500 MB/sec
bandwidth.
120 240
121
120 240
121
+
R
. .
.
1 51
2 52
Mini PCIE
PCI Express x1 slot
Jumper Settings
This chapter explains how to configure the motherboard’s hardware. Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this
chapter whenever in doubt.
CMOS Clear Jumper-JP1
Close Open * = Default setting.
If you want to clear the system conguration, use the JP1 (Clear CMOS Jumper) to clear data.
Notice:
1. Be sure to save the CMOS setting when exit the CMOS.
2. If the CPU is frequency multiplier locked, no CPU speed change will be seen
even if the frequency multiplier setting in CMOS setup is changed.
BIOS Selection Jumper(Optional)-JP3
JP1 Selection
1-2* Normal*
2-3 CMOS Clear
1
1
JP3 Selection
1-2* Master*
3-4 backup
5-6 factory
1
2
5
6
1
2
5
6
1
2
5
6

17
Conguring the BIOS
This section discusses how to change the system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly
setting the BIOS parameters is critical to maintain optimal system performance.
Use the following procedure to verify/change BIOS settings.
1. Power on the computer.,
2. Press the Del key when the following message briefly displays at the bottom of
the screen during the Power On Self Test (POST).
Pressing Del takes you to the BIOS Setup Utility.
Note: It is strongly recommended that you do not change the default BIOS
settings. Changing some settings could damage your computer.
Configuring the BIOS

18
IONITX Synergy Series Motherboard
Main Menu
Note: Note that the data in gray is non-changeable, and the others are for
selection.
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
q AMI BIOS
Displays the auto-detected BIOS information
q Processor
Display the auto-detected CPU specification
q System Memory
Displays the auto-detected system memory
q System time
Allows you to set the system time
Advanced Menu
The Advanced menu items allow you to change the setting for the CPU and other
system devices.Press <enter> to display the configuration options:
CPU Conguration
The items in this menu show the CPU-related information that the BIOS automatically
detects. Press <enter>to display the configuration options:
q Configure advanced CPU settings
Displays the auto-detected CPU information

19
Configuring the BIOS
q Max CPUID Value Limit
Allows you to determine whether to limit CPUID maximum value. Set this item
to [Disable] Windows XP operating system; set this item to [Enable] for legacy
operating system such as Windows NT4.0..
q Execute Disable Bit Capability
This function enhances protection of your computer , reducing exposure to viruses
and malicious buffer overflow attacks when working with its supporting software
and system.
q Hyper Threading Technology
Enabled this function for Windows and Linux4 OS, (OS support Hyper Threading
Technology)
Disabled this function for other OS.(OS not optimized for Hyper Threading
Technology)
IDE Conguration
The items in this menu allow you to set or change the configurations for the IDE
devices installed in the system. Press <enter>to display the configuration options:
q On-chip SATA Controller
This item allow you to enabled or disabled the SATA controller.
q SATA Mode select
This item allow you to set the SATA to IDE/AHCI/RAID mode.
q Hard Disk Write Protect
This will be effective only if device is accessed through BIOS.
q IDE Detect Time Out
The items allow you to select the time out value for detecting ATA/ATAPI devices.
q ATA(PI) 80pin cable detection
The items allow you to select the mechanism for detecting 80pin ATA(PI) cable.
Floppy Conguration
The items in this menu allow you to set or change the configurations for the floppy
devices installed in the system.
ACPI Conguration
The items in this menu allow you to setting general APCI configuration.
APM Conguration
These items allow you to configure Advanced Power Management.
Event Log Conguration
Make as read,clear,or view Event log statistics.
MPS Conguration
The items in this menu allow you to configure MPS.
PCI Express Conguration
The items in this menu allow you to enable or disable PCI Express L0S and L1 link
power states.
Smbios Conguration
SMBIOS SMI wrapper support for PnP Function 50h-54h.
USB Conguration
The items in this menu allow you to change the USB-related features .Press <enter>
To display the configuration options:
q Legacy USB Support
Allows you to enable or disable support for USB devices on legacy operating
systems.
q USB 2.0 Controller Mode
Allows you to configure the USB 2.0 controller in HiSpeed or Full Speed .