Zotac nForce 630i - ITX User manual

1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
Electronic Emission Notices
WARNING!

2
NForce 610i/630i-ITX series Motherboard
Table of Contents
Motherboard Specifications ------------------------------------------------------------------- 4
Motherboard Layout------------------------------------------------------------------------------ 5
Hardware Installation ---------------------------------------------------------------------------- 7
Safety Instructions ----------------------------------------------------------------------------- 7
Preparing the Motherboard ------------------------------------------------------------------ 7
Installing the CPU------------------------------------------------------------------------------ 7
Installing the CPU Fan------------------------------------------------------------------------ 8
Installing Memory DIMMs -------------------------------------------------------------------- 8
Installing the Motherboard ------------------------------------------------------------------- 8
Installing the I/O Shield ----------------------------------------------------------------------- 9
Connecting Cables and Setting Switches------------------------------------------------ 9
24-pin ATX Power Connector-PW1 --------------------------------------------------- 10
4-pin ATX_12V power connector-PW2----------------------------------------------- 10
Serial Port Header-COM ---------------------------------------------------------------- 11
SPDIFOut Header(optional) ----------------------------------------------------------- 11
Speaker Header-SPK -------------------------------------------------------------------- 11
Hard Disk Connector-IDE --------------------------------------------------------------- 11
Front Panel Header-FP1 ---------------------------------------------------------------- 12
USB Headers------------------------------------------------------------------------------- 12
Front Pannel Audio Header-FP_S1--------------------------------------------------- 13
Serial-ATA (SATA) Connectors(Optional)-------------------------------------------- 13
Fan Connectors---------------------------------------------------------------------------- 14
Expansion Slots---------------------------------------------------------------------------- 14
PCI Express x1 Slots(optional)----------------------------------------------------- 14
Jumper Settings --------------------------------------------------------------------------- 14
Configuring the BIOS ---------------------------------------------------------------------------- 15
Enter BIOS Setup----------------------------------------------------------------------------------- 15
Main Menu --------------------------------------------------------------------------------------- 16
Standard CMOS Features Menu----------------------------------------------------------- 17
Date and Time------------------------------------------------------------------------------ 17
IDE Channel -------------------------------------------------------------------------------- 17
Drive A---------------------------------------------------------------------------------------- 17
Video------------------------------------------------------------------------------------------ 17
Halt On --------------------------------------------------------------------------------------- 18
Memory -------------------------------------------------------------------------------------- 18
Advanced BIOS Features-------------------------------------------------------------------- 19
CPU Features ------------------------------------------------------------------------------ 19
Hard Disk Boot Priority------------------------------------------------------------------- 20

3
Table of Contents
Advanced Chipset Features----------------------------------------------------------------- 21
Integrated Peripherals Menu ---------------------------------------------------------------- 22
Power Management Setup Menu ---------------------------------------------------------- 23
PnP/PCI Configuration------------------------------------------------------------------------ 24
PC health status-------------------------------------------------------------------------------- 25
Frequency/Voltage Control ------------------------------------------------------------------ 25
Load Fail-safe Defaults ----------------------------------------------------------------------- 26
Load Optimized Defaults --------------------------------------------------------------------- 26
Set Supervisor/User Password ------------------------------------------------------------- 26
Save & Exit Setup------------------------------------------------------------------------------ 27
Exit Without Saving---------------------------------------------------------------------------- 28
Flash Update Procedure -------------------------------------------------------------------- 28
Installing Drivers and Software -------------------------------------------------------------- 29
Drivers Installing ------------------------------------------------------------------------------- 29
REALTEK HD AUDIO DRIVER SETUP ------------------------------------------------- 32
Getting Started ----------------------------------------------------------------------------- 32
Sound Effect -------------------------------------------------------------------------------- 32
Environment Simulation ------------------------------------------------------------ 32
Equalizer Selection ------------------------------------------------------------------ 32
Frequently Used Equalizer Setting----------------------------------------------- 33
Karaoke Mode------------------------------------------------------------------------- 33
Mixer------------------------------------------------------------------------------------------ 33
Playback control ---------------------------------------------------------------------- 34
Recording control--------------------------------------------------------------------- 34
Audio I/O------------------------------------------------------------------------------------- 35
Speaker Configuration -------------------------------------------------------------- 36
Connector Settings------------------------------------------------------------------- 36
S/PDIF ---------------------------------------------------------------------------------- 37
Speaker Calibration------------------------------------------------------------------ 37
Microphone---------------------------------------------------------------------------------- 38
Noise Suppression ------------------------------------------------------------------- 38
Beam Forming ------------------------------------------------------------------------ 38
Acoustic Echo Cancellation -------------------------------------------------------- 38
Audio Demo--------------------------------------------------------------------------------- 39
Information ---------------------------------------------------------------------------- 39
SATA RAID User Manual ------------------------------------------------------------------------ 40
Setting up the BIOS --------------------------------------------------------------------------- 40
Entering the RAID BIOS Setup ------------------------------------------------------------- 41
Installing the RAID Drives-------------------------------------------------------------------- 42

4
NForce 610i/630i-ITX series Motherboard
Motherboard Specications
qChipset
NVIDIA MCP73 Series
qSize
Mini-ITX form factor of 170mm x 170mm
qMicroprocessor support
Intel LGA 775 Celeron® , Pentium® 4, Pentium® D, CoreTM 2 Series
qOperating systems:
Supports Windows XP 32bit/64bit and Windows Vista 32bit/64bit
qSystem Memory support
Supports DDRII533/667(DDRII800 for NForce630i series). Supports up to 4GBs
DDRII memorys.
qUSB 2.0 Ports*
v Supports hot plug and play
v Ten USB 2.0 ports (six rear panel ports, four from onboard USB headers)
v Supports wake-up from S1
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
qOnboard Serial ATA II
v Independent DMA operation on two ports (optional).
vData transfer rates of 3Gb/s.
qOnboard LAN
vLAN interface built-in onboard
v Supports 10/100Mbps Ethernet
qOnboard Audio(optional)
v Azalia High-Definition audio
v Supports 6-channel
v Supports Jack-Sensing function
qGreen Function
v Supports ACPI (Advanced Configuration and Power Interface)
v RTC timer to power-on the system
v AC power failure recovery
qOnboard Graphics support
v Integrated 300MHz DAC for external desktop display.
qExpansion Slots
v One PCI Express x1 slot(optional)

5
Motherboard Layout
Figure 1 shows the motherboard and Figure 2 shows the back panel connectors.
Motherboard Layout
Figure 1. Board Layout
120 240
121
120 240
121
+
LOTES
R E O EVM
Chiset
DDRII1 DDRII2
PW1
S FAN1_FP1
SATA1
SATA2
COM
PCIEX1
SPDIF
C FAN1_
FP S1
_
FP U2
_
FP U1
_
JP1
PW2
DVI
USBU_LAN
SD1
KB1
2
3
45
6
7
8
9
10
11
12
13 14
15 16
SPK
17
JP2
IDE
VGA
18 19
24-pin ATX Power Connector-PW1
Hard Disk Connector-IDE
Front Panel Header-FP1
Speaker Header-SPK
Serial-ATA (SATA) Connectors(optional)
SYS Fan connector
Serial Port Header-COM
SPDIF-OUT Header(optional)
PCI Express x1 slot(optional)
Front Pannel Audio Header-FP_S1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Clear CMOS Jumper
Backpanel connectors
P/S port 5V standby selection Power
4-pin ATX_12V power connector-PW2
CPU Fan connector
USB Headers
CPU socket
Chipset
DDRII DIMM Sockets
11.
12.
13.
14.
15.
16.
17.
18.
19.

6
NForce 610i/630i-ITX series Motherboard
6. Port 2-Channel 4-Channel 6-Channel
Blue Line-In Rear Speaker Out Rear Speaker Out
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Center/Subwoofer
7. LAN Connector
Lan Port with LEDs to indicate status.
· Yellow/Light Up/Blink = 10 Mbps/Link/Activity
· Yellow and Green/Light Up/Blink = 100 Mbps/link/Activity
Figure 2: Backpanel connectors
6
11
5
10
15
23456
7
1. PS/2 Mouse Port
2. PS/2 Keyboard Port
3. VGA Connector
4. DVI Connector(optional for NForce630i-ITX)
5. USB Connectors

7
Hardware Installation
This section will guide you through the installation of the motherboard. The topics
covered in this section are:
q Preparing the motherboard
v Installing the CPU
v Installing the CPU fan
v Installing the memory
q Installing the motherboard
qConnecting cables and setting switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precations.
Remember to remove power from your computer by disconnecting the AC main source
before removing or installing any equipment from/to the computer chassis.
Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU and memory. You need
to purchase these to complete this installation.
Installing the CPU
Be very careful when handling the CPU. Make sure not to bend or break any pins on
the back. Hold the processor only by the edges and do not touch the bottom of the
processor.
Use the following procedure to install the CPU onto the motherboard.
Unhook the socket lever by pushing down and away from the
socket.
Lift the load plate.There is a protective socket cover on
the load plate to protect the socket when there is no CPU
installed.
Remove the protective socket cover from the load plate.
Remove the processor from its protective cover,making sure
you hold it only by the edges.It is a good idea to save the
cover so that whenever you remove the CPU, you have a
safe place to store it.
Align the notches in the processor with the notches on the
socket.
Lower the processor straight down into the socket with out
tilting or sliding it into the socket.
Close the load plate over the CPU and press down while you
close and engage the socket lever.
Note:Make sure the CPU is fully seated and level in
the socket.
1.
2.
3.
4.
5.
6.
7.
Hardware Installation

8
NForce 610i/630i-ITX series Motherboard
Installing the CPU Fan
There are many different fan types that can be used with this motherboard. Follow the
instruction that came with your fan assembly. Be sure that the fan orientation is correct
for your chassis type and your fan assembly.
Installing Memory DIMMs
Your new motherboard has two 1.8V 240-pin slots for DDR2 memory. These slots
support 256 Mb, 512 Mb, 1Gb and 2Gb DDR2 technologies. There must be at least
one memory bank populated to ensure normal operation. Use the following the recom-
mendations for installing memory.
q One DIMM:Install into slot 1 or 2. You can install the DIMM into any slot,however,
slot 1 is preferred.
q Two DIMMs: Install into slots 1 and 2. The idea is to not have the DIMMs in adja
cent slots.
Use the following procedure to install memory DIMMs into the slots on the
motherboard. Note that there is only one gap near the center of the DIMM slot. This
slot matches the slot on the memory DIMM to ensure the component is installed
properly.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into
the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock
the DIMM into the connector.
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis
you are using and if you are replacing an existing motherboard or working with an
empty chassis. Determine if it would be easier to make all the connections prior to this
step or to secure the motherboard and then make all the connections. It is normally
easier to secure the motherboard first.
Use the following procedure to install the I/O shield and secure the motherboard into
the chassis.
Note:Be sure that the CPU fan assembly has enough clearance for the chassis
covers to lock into place and for the expansion cards. Also make sure the CPU
Fan assembly is aligned with the vents on the covers.
120 240
121
120 240
121
+
LOTES
R E O EVM
DDRII-1
DDRII-2

9
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust and foreign objects, and
promotes correct airflow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis.
Press the I/O shield into place and make sure it fits securely. If the I/O shield does
not fit into the chassis, you would need to obtain the proper size from the chassis
supplier.
Connecting Cables and Setting Switches
This section takes you through all the connections and switch settings necessary on
the motherboard. This will include:
q Power Connections
v 24-pin ATX Power Connector-PW1
v 4-pin ATX_12V power connector-PW2
q Internal Headers
v Serial Port Header-COM
v SPDIF Out Header(Optional)
v Speaker Header-SPK
v Hard Disk Connector-IDE
v Front Panel Header-FP1
v USB Headers
v Front Pannel Audio Header-FP_S1
q Serial ATA II
q Chassis Fans
q Expansion slots
q Jumper settings
Hardware Installation

10
NForce 610i/630i-ITX series Motherboard
120 240
121
120 240
121
+
LOTES
R E O EVM
4-pin ATX_12V power connector-PW2
PW2, the 4-pin ATX 12V power connection, is used
to provide power to the CPU. Align the pins to the
connector and press firmly until seated.
PW1-Pin Assignments
Pin Signal Pin Signal
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWROK 20 -5V
9 +5V_AUX 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 GND
112
13
24 PW1
24-pin ATX Power Connector-PW1
PW1 is the main power supply connector located along the edge of the board next to
the DIMM slots. Make sure that the power supply cable and pins are properly aligned
with the connector on the motherboard. Firmly plug the power supply cable into the
connector and make sure it is secure.
PW2-Pin Definition
Pin Signal
1 GND
2 GND
3 +12V
4 +12V
1
2
3
4
PW2

11
Hard Disk Connector-IDE
The motherboard has a 32-bit Enhanced PCI IDE and
Ultra DMA 66/100/133 controller that provides PIO
mode 0~4, Bus Master, and Ultra DMA 66/100/133
function. You can connect up to two hard disk drives,
CD-ROM, 120MB Floppy (reserved for future BIOS)
and other devices.
120 240
121
120 240
121
+
LOTES
R E O EVM
Hardware Installation
SPK
1
Speaker Header-SPK
IDE
1
SPDIF Out Header(optional)
This header provides a SPDIF (Sony/Philips Digital
Interface)output to digital multimedia device through
coaxial connector.
1
SPDIF
SPDIF-Pin Definition
Pin Signal
1 SPDIF-out
2 +3.3V
3 NC
4 GND
SPK-Pin Definition
Pin Signal
1 VCC
2 NC
3 NC
4 SPK-
Serial Port Header-COM
COM
1
2
9
10
COM-Pin Definition
Pin Signal Pin Signal
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND 10 NC

12
NForce 610i/630i-ITX series Motherboard
Front Panel Header-FP1
The front panel header on this motherboard is one connector used to connect the fol-
lowing four cables:
q PWRLED
Attach the front panel power LED cable to these two pins of the connector. The
Power LED indicates the system’s status.
q PWR SW
Attach the power button cable from the case to these two pins. Pressing the
power button on the front panel turns the system on and off rather than using the
power supply button.
q HDD LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator
LED indicates the activity status of the hard disks.
q RST SW
Attach the Reset switch cable from the front panel of the case to these two pins.
The system restarts when the RESET switch is pressed.
120 240
121
120 240
121
+
LOT ES
R E O EVM
Note:
Some chassis do not have all four cables.Be sure to match the name
on the connectors to the corresponding pins.
1 2
9 10
FP1
FP1-Pin Definition
Pin Signal Pin Signal
1 HDD_LED+ 6 PWR_SW
2 PW_LED+ 7 RESET
3 HDD_LED- 8 GND
4 PW_LED- 9 NC
5 GND 10 KEY
USB Headers
This motherboard contains six USB 2.0 ports that are exposed on the rear
panel of the chassis(Figure 2). The motherboard also contains two 10-pin
internal header connectors onboard.
1. Secure the bracket to either the front or rear panel of your chassis (not all
chassis are equipped with the front panel option).
USB-Pin Definition
PIN Assignment PIN Assignment
1 VCC 6 USBP1+
2 VCC 7 GND
3 USBP0- 8 GND
4 USBP1- 9 KEY
5 USBP0+ 10 OC#
1
2
9
10
FP_U1
1
2
9
10
FP_U1

13
Hardware Installation
120 240
121
120 240
121
+
LOTES
R E O EVM
Front Pannel Audio Header-FP_S1
The audio connector supports HD audio standard and provides two kinds of audio
output choices: the Front Audio, the Rear Audio. The front Audio supports re-tasking
function.
Note:
In order to utilize the front audio header, your chassis must have front audio
connector. Also please make sure the pin assignment on the cable is the
same as the pin assignment on the mainboard header. To find out if the
chassis you are buying supports a front audio connector, please contract
your dealer.
FP_S1-Pin Definition
PIN Assignment PIN Assignment
1 MIC2(L) 6 Reserved
2 GND 7 FAVDIO-JD
3 MIC(R) 8 Key(No pin)
4 -ACZ-DET 9 Front Audio(L)
5 Front Audio(R) 10 Reserved
1 2
9 10
FP_S1
Serial-ATA (SATA) Connectors(Optional)
The Serial ATA II connector is used to connect the Serial ATA II device to
the motherboard.These connectors support the thin Serial ATA II cables
for primary storage devices.The current Serial ATA II interface allows up
to 3Gb/s data transfer rate.
There are two serial ATA connectors on the motherboard that support
AHCI and RAID configurations.
SATA-Pin Definition
Pin Signal
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
1 1
SATA-2 SATA-1

14
NForce 610i/630i-ITX series Motherboard
120 240
121
120 240
121
+
LOTES
R E O EVM
Fan Connectors
There are two Fan Connectors on the motherboard. The fan speed can be detected
and viewed in the PC Health Status section of the CMOS Setup.
CPU FAN Connector
GND
+12V
Sense
Control
SYS FAN Connector
Sense
+12V
GND
Expansion Slots
The NVIDIA MCP73 motherboard contains one PCI Express x1 slot.
PCI Express x1 Slots(optional)
There is one PCI Express x1 slot that is designed to accommodate
less bandwidth-intensive cards, such as a modem or LAN card. The x1
slot provides 250 MB/sec bandwidth.
PCI Express x1 Slot
Jumper Settings
This chapter explains how to configure the motherboard’s hardware. Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this
chapter whenever in doubt.
Notice:
1. Be sure to save the CMOS setting when exit the CMOS.
2. If the CPU is frequency multiplier locked, no CPU speed change will be seen
even if the frequency multiplier setting in CMOS setup is changed.
CMOS Clear Jumper-JP1
JP1 Selection
1-2* Normal*
2-3 CMOS Clear
1
1
Close Open * = Default setting.
JP2 Selection
1-2* 5V standby power input*
2-3 5V power input
1
1
P/S Port 5V Standby Power Jumper-JP2(Optional)
If you want to clear the system configuration,use the JP1(Clear CMOS Jumper) to clear data

15
Conguring the BIOS
This section discusses how to change the system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
This section includes the following information:
q Enter BIOS Setup
q Main Menu
q Standard CMOS Features
q Advanced BIOS Features
q Advanced Chipset Features
q Integrated Peripherals
q Power Management Setup
q PnP/PCI Configurations
q Pc health status
q Frequency/Voltage Control
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly
setting the BIOS parameters is critical to maintain optimal system performance.
Use the following procedure to verify/change BIOS settings.
1. Power on the computer.,
2. Press the Del key when the following message briefly displays at the bottom of
the screen during the Power On Self Test (POST).
Press F1 to continue, DEL to enter Setup.
Pressing Del takes you to the Phoenix-Award BIOS CMOS Setup Utility.
Note: It is strongly recommended that you do not change the default BIOS
settings. Changing some settings could damage your computer.
Configuring the BIOS

16
NForce 610i/630i-ITX series Motherboard
Main Menu
The main menu allows you to select from the list of setup functions and two exit
choices. Use the Page Up and Page Down keys to scroll through the options or press
Enter to display the associated submenu. Use the # $ arrow keys to position the
selector in the option you choose. To go back to the previous menu, press Esc.
q Standard CMOS Features
Use this menu to set up the basic system configuration.
q Advanced BIOS Features
Use this menu to set up the advanced system features and boot sequence.
q Advanced Chipset Features
Use this menu to optimize system performance.
q Integrated Peripherals
Use this menu to set up onboard peripherals such as IDE, RAID, USB and LAN
control.
q Power Management Setup
Use this menu to configure power management, power on, and sleep features.
q PnP/PCI Configurations
Use this menu to modify the system’s Plug-and-Play and PCI configurations.
q Pc health status
Use this menu to monitor the real-time system status of your PC.
The following items on the CMOS Setup Utility main menu are commands rather than
submenus:
q Load Optimized Defaults
Load default system settings.
q Set Supervisor and User Password
Use this command to set, change, and disable the password used to access the
system and the BIOS menu.
q Save & Exit Setup
Use this command to save settings to CMOS and exit setup.
q Exit Without Saving
Use this command to abandon all setting changes and exit setup.
Note:
that on the BIOS screens all data in
white is for information only,data in
yellow is changeable, data in blue is
non-changeable, and data in a red
box is highlighted for selection.

17
Configuring the BIOS
Standard CMOS Features Menu
The Standard CMOS Features menu is used to configure the standard CMOS
information, such as the date, time, HDD model, and so on. Use the Page Up and
Page Down keys to scroll through the options or press Enter to display the sub-menu.
Use the # $ arrow keys to position the selector in the option you choose. To go back
to the previous menu, press Esc.
The information shown in Item Help corresponds to the option highlighted.
Note:
that all data in white is for information
only, data in yellow is changeable,
data in blue is non-changeable, and
data in a red box is highlighted for
selection.
Date and Time
Using the arrow keys, position the cursor over the month, day, and year. Use the Page
Up and Page Down keys to scroll through dates and times. Note that the weekday
(Sun through Sat) cannot be changed. This field changes to correspond to the date you
enter. Note that the hour value is shown in a 24-hour clock format. Time is represented
as hour : minute : second.
IDE Channel
Use these functions to detect and configure the individual IDE channels. Select a
channel and press Enter to display the IDE sub-menu.
Press Enter to auto-detect IDE channels in the system. Once the channel is detected,
the values for Capacity, Cylinder, Head, Precomp, Landing Zone, and Sector are
automatically filled in.
q None
There is no HDD installed or set.
q Auto
The system can auto-detect the hard disk when booting up.
q Manual
When you set the channel to [Manual] and change Access Mode to [CHS], you
can then enter the number of cylinders,heads,Precomp,landing zone,and sector.
Drive A
The Drive A option allows you to select the kind of FDD to install.
Video
Use this option to choose the mode of Video, as EGA/VGA, CGA 40, CGA 80, MONO.

18
NForce 610i/630i-ITX series Motherboard
Halt On
Halt On determines whether or not the computer stops if an error is detected during
power on. Use the Page Up and Page Down keys to scroll through the options or
press Enter to display the Halt On sub-menu. Use the # $ arrow keys to position
the selector in the option you choose. Press Enter to accept the changes and return
to the Standard CMOS Features menu.
q All Errors
Whenever the BIOS detects a nonfatal error, the system stops and prompts you.
q No Errors
System boot does not stop for any detected errors.
q All, But Keyboard
System boot does not stop for keyboard errors, but does stop for all other errors.
q All, But Diskette
The system boot does not stop for a diskette error but will stop for all other errors.
q All, But Disk/Key
The system boot does not stop for a diskette or keyboard error but will stop for all
other errors.
Memory
These settings are display-only values that are determined by the BIOS POST
(Power-On Self Test).
q Base Memory
BIOS POST determines the amount of base (or conventional) memory installed
in the system.
q Extended Memory
BIOS determines how much extended memory is present during the POST.
q Total Memory
This value represents the total memory of the system.

19
Configuring the BIOS
Advanced BIOS Features
Access the Advanced BIOS Features menu from the CMOS Utility Setup screen. Use
the Page Up and Page Down keys to scroll through the options or press Enter to
display the sub-menu. Use the # $ arrow keys to position the selector in the option
you choose. To go back to the previous menu, press Esc.
Note:
The options that have associated sub-
menus are designated by a u, which
precedes the option. Press Enter to
display the sub-menus.
Note:
that all data in white is for information
only, data in yellow is changeable,
data in blue is non-changeable, and
data in a red box is highlighted for
selection.
CPU Feature
Press Enter to display CPU Feature menu,then the following items will be displayed:
q PPM Mode
Use this option to choose the mode of PPM.
q Limit CPUID MaxVal
Use this option to enable or disable the function of Limiting CPUID MaxVal
q C1E Function
Select CPU C1E function.
q Execute Disable Bit
When disabled forces the XD feature flag to always return 0,defaults choose
Enable.
q Virtualization Technology
Use this option to enable or disable Virtualization Technology.
q Core Multi-Processing
Use this option to enable or disable Core Multi-Processing.