ZUUM Media LSPTZ-2MP-IP-4.8-120MM User manual

4-inch IR Speed Dome Installation Manual
Version 1.0.1

ZM111317
i
Table of Contents
1
!
SPEED DOME INSTALLATION
........................................................................... 1!
1.1
!
Installation Environments
......................................................................................................................1!
1.2
!
Check installation space and installation location intension
............................................................1!
1.3
!
About cable
..............................................................................................................................................1!
1.4
!
Select required power supply cable according to transmission distance
......................................2!
1.5
!
Please keep all package material well for future use
........................................................................2!
2
!
SETUP BEFORE INSTALLATION
....................................................................... 3!
2.1
!
Check Accessories
.................................................................................................................................3!
2.2
!
Open Device
............................................................................................................................................3!
2.3
!
Dial Switch Setup
....................................................................................................................................3!
2.3.1!Dial Location and Function...............................................................................................................3!
2.3.2!Dial Setting..........................................................................................................................................5!
2.3.3!Address Setting .................................................................................................................................. 5!
2.3.4!Baud Rate, Parity and HD/SD Video Mode Setting...................................................................... 5!
2.3.5!Terminal Matching Resistance Setup .............................................................................................6!
2.4
!
RESET and SD Card Installation (Network Speed Dome)
..............................................................7!
2.5
!
Cable Connection
...................................................................................................................................7!
3
!
INSTALLATION
.................................................................................................... 8!
3.1
!
Component Installation
..........................................................................................................................8!
3.2
!
Wall Mount Installation Steps
................................................................................................................9!
3.2.1!Installation Environments..................................................................................................................9!
3.2.2!Installation Steps................................................................................................................................9!
4
!
APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE PROTECTION
......... 14!
5
!
APPENDIX Ⅱ ABOUT RS485 BUS
.................................................................... 15!

ZM111317
ii
5.1
!
RS485 Bus Main Feature
....................................................................................................................15!
5.2
!
RS485 Bus Transmission Distance
...................................................................................................15!
5.3
!
The Problem in Practical Use
.............................................................................................................15!
5.4
!
RS485 Bus FAQ
....................................................................................................................................16!
6
!
APPENDIX Ⅲ THE AC 24V WIRE GAUGE AND TRANSMISSION DISTANCE
RELATIONSHIP SHEET
........................................................................................... 17!
7
!
APPENDIX Ⅳ DC 12V WIRE GAUGE AND TRANSMISSION DISTANCE
RELATIONSHIP SHEET
........................................................................................... 18!
8
!
APPENDIX V WIRE GAUGE REFERENCE SHEET
......................................... 19!
Welcome
Thank you for purchasing our Network speed dome camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual for future reference!
Important Safeguards and Warnings
1
．
Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply
requirement is subject to the device label).
Please prevent the line cord from being damaged, especially the plug, power socket and the
junction from the device.

ZM111317
iii
Note: Do not connect PoE and standard 12V power supply sources to the device at the
same time; it may result in device damage!
We assume no liability or responsibility for fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2
．
Environment
Please do not aim the device at strong light (such as lightning, sunlight etc.) to focus; otherwise it
may cause overexposure (It is not the devices malfunction), which will affect the longevity of
CCD or CMOS.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold
and with strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid to fall into the camera to prevent internal components
to be damaged.
Please keep the camera well ventilated to prevent heat accumulation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
Heavy stress, violent vibration or heavy water splash are not allowed during transportation,
storage and installation.
3. Operation and Daily Maintenance
Please do not touch the heat dissipation component of the device directly to avoid burn.
Please do not dismantle the device; there is no component which can be fixed by users
themselves in the camera. It may cause water leakage or bad image for the device due to
unprofessional dismantling.
It is recommended to use the device with surge proof device to improve surge resistance.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the
dust or dirt on the lens surface. Please use a dry cloth moistened by alcohol to wipe away the
dust gently if it is necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water
to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to
clean the device. Don’t use volatile solvent like alcohol, benzene, thinner etc. or strong detergent
with abrasiveness, otherwise it will damage the surface coating or reduce the working
performance of the device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to deal with once dirt is found:
- Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
- Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or

ZM111317
iv
paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change
the cloth and wipe several times if it is not clean enough.
Warning
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional installers.
Please prevent the device surface from the radiation of a laser beam when using laser beam
devices.
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
All installation and operations should conform to your local electrical safety codes. We assume
no liability or responsibility for all fires or electrical shock caused by improper handling or
installation.
Do not connect serval speed dome cameras to one power adapter. It may result in overheating
or fire if it exceeds the rated load.
Before you connect cable, install or uninstall or begin any work, please turn off the power and
unplug cable.
Please turn off power and unplug cables immediately if there is any smoke, bad smells, or noise.
Please contact technical support.
All work should be done by a trained service installer. We are not liable for any problems caused
by unauthorized modifications or attempted repair.
Please make sure no objects fall or flammable substances get into the speed dome camera. This
could result in fire, short-circuit or damage.
Please power down and unplug camera cables immediately if there is any liquid falling into or
inside camera.
Please use caution when locating a mounting location. Rain and sea water can erode the camera.
Notate the cameras IP rating for best application.
This series speed dome should be installed inside in a cool dry location away from sunlight.
This series speed dome should be kept away from strong electromagnetic radiant, please keep
away from wireless power, TV transmitter etc.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly updated according to the product update; the updated content will
be added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurring when using the
device.
Please contact customer service for the latest procedure and supplementary documentation.

ZM111317
v
There may be deviation between the actual value of some data and the value provided in the
manual due to the reasons such as the real environment is not stable and so on. Please refer to
the company’s final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the
manual.
FCC Information
1. FCC conditions：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
l This device may not cause harmful interference;
l This device must accept any interference received, including interference that may cause
undesired operation.
2. FCC compliance：
This equipment has been tested and found to comply with the limits for a digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference. This equipment generates and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
l Consult the dealer or an experienced radio/TV technician for help.
Note:
Please refer to the website for more details, check and download corresponding user’s manual
and tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
Download from WEB
Installation Accessories Bag
1

ZM111317
1
1 SPEED DOME INSTALLATION
1.1 Installation Environments
Basic Requirement
l All installation and operation here should conform to your local electrical safety codes.
l Before installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirements, please contact your local retailer for more
information.
l We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
1.2 Check installation space and installation location
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain 8X’s the weight of the speed dome.
1.3 About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
l 75 ohm.
l Full cable with copper conductor
l 95% knitted copper shield
l RS485 communication cable, refer to appendix 2
International Model
Max Transmission Distance
(Ft\M)
RG59/U
750Ft (229M)
RG6/U
1,000Ft (305M)
RG11/U
1,500Ft (457M)
Note:
The above can be applied to analog speed dome and network speed dome
International Mode
Max Transmission Distance(Ft\M)
SYV-75-3
720P（25fps\30fps)：500M/1640Ft
720P（50fps\60fps)：300M/984Ft
1080P（25fps\30fps):300M/984Ft
Note:
The above can be applied to HDCVI speed dome

ZM111317
2
1.4 Select required power supply cable according to transmission
distance
l For AC 24V series product, please refer to Appendix 3.
l For DC 12V series product, please refer to Appendix 4.
1.5 Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Note:
Non-original package material may result in device damage during the transportation.

ZM111317
3
2 SETUP BEFORE INSTALLATION
2.1 Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are included.
2.2 Open Device
Remove the package and then take out the device. See Figure 2-1.
Figure 2-1
2.3 Dial Switch Setup
2.3.1 Dial Location and Function
The corresponding functions of dial switch for analog speed dome and HDCVI speed dome are
different, which will be respectively introduced below.
2.3.1.1 Analog Speed Dome
Open the rear cover and you can see there is a dial switch on the PTZ mainboard which you can
use to set the speed dome address, baud rate and parity etc. See Figure 2-2.

ZM111317
4
Figure 2-2
2.3.1.2 HDCVI Speed Dome
Open the rear cover and you can see there is a dial switch on the PTZ mainboard which you can
use to set the speed dome address, baud rate and HD/SD video format etc. Please refer to
Figure 2-3.
Figure 2-3

ZM111317
5
2.3.2 Dial Setting
Before you control the speed dome, please set the speed dome address number, baud rate, and
parity or HD/SD video mode. The speed dome will respond to its control command after
completing all these settings.
Note:
Open speed dome rear cover, you can see the dial switch buttons on the PTZ mainboard. You
can follow the steps listed below to set the speed dome address number, baud rate, and parity or
HD/SD video mode. Please be noted that you need to restart the device to activate the new
settings.
The dial switches on the PTZ are used to set speed dome address, baud rate, and parity or
HD/SD video mode parameters. When you switch ON as 1, then 1 is the lowest bit and 8 is the
highest bit in address setting dial switch; for baud rate and parity or HD/SD video mode setting, 9
is the lowest bit and 12 is the highest bit.
Note:
Please be noted that the speed dome can self-adapt to the industrial standard protocol, PELCO-
D and PELCO-P, the control protocol doesn’t need to be set via dial setting.
2.3.3 Address Setting
The speed dome uses dial switch to set address number, the encoding mode adopts binary
system. 1 to 8 is valid bit, and the highest address bit is 255. You can refer to sheet 2-1 for more
information about address number setting.
Address
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
……
…………………………………………………………………
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
Sheet 2-1
2.3.4 Baud Rate, Parity and HD/SD Video Mode Setting
2.3.4.1 Analog Speed Dome
Bit 9 and 10 are used to set baud rate in the dial bit from 9 to 12, bit 11 and 12 are used to set
parity. Please refer to sheet 2-2 and 2-3 for detailed information.
9
10
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Sheet 2-2

ZM111317
6
11
12
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
Sheet 2-3
2.3.4.2 HDCVI Speed Dome
Bit 9 and 10 are used to set baud rate in the dial bit from 9 to 12, bit 11 and 12 are used to set
HD/SD video mode. Please refer to sheet 2-4 and 2-5 for detailed information.
9
10
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Sheet 2-4
11
12
Parity
OFF
OFF
HD
ON
OFF
SD
OFF
ON
Self-adapt
ON
ON
HD
Sheet 2-5
2.3.5 Terminal Matching Resistance Setup
The connection mode of device terminal 120Ω resistance, the terminal resistance 120Ω already
exists on the power board, there are two connection modes, see Figure 2-4.
120Ω
1- 2
ON
2- 3
OFF
Figure 2-3
The factory default setup is shown as in Figure 2-5. Right now, the jumper (Connection board) is
on the pin 2 and pin 3. The 120Ω resistance does not connect to the device.
Figure 2-5
If you want to connect the 120Ω resistance, please remove the jumper from the pin 2 and pin 3
and connect to pin 1 and pin 2. Now the 120Ω is connected to the circuit. See Figure 2-6.

ZM111317
7
Figure 2-6
2.4 RESET and SD Card Installation (Network Speed Dome) IP
Open the rear cover and you can see there is a reset button and a SD card slot on the PTZ
mainboard (see Figure 2-7). The reset button is used to reset network system and SD card is
used to store data.
Figure 2-7
2.5 Cable Connection
Please connect the power cable, video output cable, audio cable, RS485 control cable, alarm
input/output pin, network cable, and high-frequency cable according to your actual requirements.
Please use insulation tape to seal the cable connection ports for proper waterproofing.
Note
The video port is covered with heat shrink tube of high shrinking ratio. After the video connection,
please heat the tube to make sure the video port is damp proof and waterproof.

ZM111317
8
3 INSTALLATION
The IR intelligent speed dome mainly adopts wall mount mode.
3.1 Component Installation
The wall mount bracket is shown in Figure 3-1 and Figure 3-2.
Figure 3-1
Figure 3-2

ZM111317
9
3.2 Wall Mount Installation Steps
3.2.1 Installation Environments
The wall mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
l The wall is thick enough to install the expansion bolt.
l The ceiling can at least sustain the 8x weight of the speed dome, bracket and the
accessories.
3.2.2 Installation Steps
Step 1
Draw the punch positions on the wall according to the installation holes on the bottom of the wall
mount bracket (align the bracket cable outlet hole with the round hole on the wall), and dig holes
on the wall, then insert the expansion bolts into the holes which were just dug (expansion bolts
are prepared by users themselves).
Step 2
As it is shown in Figure 3-3, lock the safety buckle well; insert the combination cable of the speed
dome from the adapter and pull it out from the other end of the wall mount bracket, then aim the
enclosure top connecting flange at the inner holes of the adapter, push the speed dome to the
bottom and tighten the three screws completely just in case the speed dome falls if it is not
installed properly.
Figure 3-3
Step 3
Insert the combination cable into the wall holes after it is connected respectively, and then use
four hex nuts and flat gasket to fix the wall mount bracket on the wall where expansion bolts are
already inserted, see Figure 3-4.

ZM111317
10
Figure 3-4
Step 4
Now the installation of the speed dome is completed, see Figure 3-5.
Figure 3-5

ZM111317
11
4 Network Configuration
The IP camera defaults to DHCP. If you are connecting directly to NVR the NVR will assign the
IPC an IP address. If you are connecting IPC to XVR or hybrid DVR accepting IP camera or if
camera is connected directly on network router make sure you change to a static IP. NOTE:
ALWAYS CHANGE PASSCODE TO IP CAMERA FOR IMPROVED SECURITY.
4.1 Modify IP Address
IP address can be acquired and modified through our quick configuration tool for the cameras
which are accessed via wired network, it needs to connect wired network to configure wireless
parameters before using wireless network cameras. In this chapter, it will introduce the approach
of modifying IP address via “Quick Configuration Tool”; also, you can modify the IP address in
the network parameters of the WEB interface, please refer to the document link for Config Tool.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same
network segment with computer IP address.
Step 1) Double click the “ConfigTools.exe” and open the quick configuration tool. See if your
camera is already in the list or click search at the top.
Step 2) Select device to be configured, the system will pop out the Modify IP Address box when
selecting Modify IP. Enter the static IP address and details to assign for this camera.
NOTE static IP is best way. DHCP will change and can cause configuration issues.
The default user name and password are admin and admin respectively, the default of port is
37777. See Figure 3-1 for more details.
Step 3)

ZM111317
12
Modify the camera IP address on the “Net” interface, click “Save” to finish modification.
See Figure 3-2 for more details.
4.2
Login WEB Interface
Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to our website for the latest documentation.
Step 1) Open IE and input the modified camera IP address in the address bar.
Step 2) The login interface is shown below, please input your user name and password (Default
user name is admin and password is admin respectively), click “login”. NOTE: Please
change the default passcode information for best security.
See Figure 3-3 for more details.

ZM111317
13
Figure 3-3
Step 3) Install controls according to the system prompt; see Figure 3-4 for the WEB main
interface. Please modify the administrator password as soon as possible after you successfully
logged in.
Figure 3-4

ZM111317
14
5 APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE
PROTECTION
This series speed dome adopts TVS lighting protection technology. It can effectively prevent
damages from various pulse signals below 6000W, such as sudden lighting and surge. While
maintaining your local electrical safety code, you still need to take necessary precaution
measures when installing the speed dome in the outdoor environment.
l The distance between the signal transmission cable and high-voltage device (or high-voltage
cable) shall be at least 50 meters.
l Outdoor cable layout shall go under cover if possible.
l For vast land, please use sealing steel tube under the land to implement cable layout and
connects one point to the earth. Open floor cable layout is forbidden.
l In area of strong thunderstorm hit or near high sensitive voltage (such as near high-voltage
transformer substation), you need to install additional high-power thunder protection device
or lightning rod.
l The thunder protection and earth of the outdoor device and cable shall be considered in the
building whole thunder protection and conform to your local national or industry standard.
l System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at
the same time conforms to your local electrical safety code. The earth device shall not short
circuit to N (neutral) line of high voltage power grid or mixed with other wires. When
connecting the system to the earth alone, the earth resistance shall not be more than 4Ω
and earth cable cross-sectional area shall be below 25 mm². See Figure 5-1.
Figure 5-1