ZUUM LSB4MP-IP-2.8-IR30-WH User manual

HD Mini IR Waterproof Bullet Network Camera
Quick Start Guide
Version 1.0.0

ZM111317
i
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual for future reference!
Important Safeguards and Warnings
1
．
Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply requirement is
subject to the device label).
Please prevent the line cord from being damaged, especially the plug, power socket and the junction
from the device.
Note: Do not connect PoE and standard 12V power supply sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for fires or electrical shock caused by improper handling or
installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2
．
Environment
Please do not aim the device at strong light (such as lighting, sunlight etc.) to focus; otherwise it may
cause overexposure (It is not the devices malfunction), which will affect the longevity of CCD or CMOS.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and with
strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid to fall into the camera to prevent internal components to be
damaged.
Please keep the camera well ventilated to prevent heat accumulation.
Please pack the device with standard factory packaging or material with same quality when transporting
the device.
Heavy stress, violent vibration or heavy water splash are not allowed during transportation, storage and
installation.
3. Operation and Daily Maintenance
Please do not touch the heat dissipation component of the device directly to avoid burn.
Please do not dismantle the device; there is no component which can be fixed by users themselves in
the camera. It may cause water leakage or bad image for the device due to unprofessional dismantling.
It is recommended to use the device with surge proof device to improve surge resistance.

ZM111317
ii
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust or
dirt on the lens surface. Please use a dry cloth moistened by alcohol to wipe away the dust gently if it is
necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with
abrasiveness, otherwise it will damage the surface coating or reduce the working performance of the
device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and
use, please refer to the following methods to deal with once dirt is found:
- Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
- Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or paper
soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth and
wipe several times if it is not clean enough.
Warning
Please use the standard accessories provided by manufacturer and make sure the device is installed
and fixed by professional installers.
Please prevent the device surface from the radiation of a laser beam when using laser beam devices.
Please do not provide two or more power supply modes for the device, otherwise it may cause damage
to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly updated according to the product update; the updated content will be
added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurring when using the
device.
Please contact customer service for the latest procedure and supplementary documentation.
There may be deviation between the actual value of some data and the value provided in the manual
due to the reasons such as the real environment is not stable and so on. Please refer to the company’s
final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the manual.
FCC Information
1. FCC conditions：

ZM111317
iii
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
l This device may not cause harmful interference;
l This device must accept any interference received, including interference that may cause undesired
operation.
2. FCC compliance：
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
Note:
Please refer to the website for more details, check and download corresponding user’s manual and
tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
Download from WEB
Installation Accessories Bag
1

ZM111317
iv
Table of Contents
1!Framework................................................................................................................................... 1!
1.1!Device External Cable ................................................................................................. 1!
1.2!Framework and Dimension......................................................................................... 1!
2!Device Installation ...................................................................................................................... 2!
2.1!Install Device................................................................................................................. 2!
3!Network Configuration............................................................. Error! Bookmark not defined.!
3.1!Modify IP Address ...................................................... Error! Bookmark not defined.!
3.2!Login WEB Interface.................................................................................................... 5!

ZM111317
1
1 Framework
1.1 Device External Cable
You can refer to the following figure for cable information. See Figure 1-1.
Figure 1-1 Cable
Please refer to the following sheet for detailed information.
SN
Port
Port name
Connector
Function description
1
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
Note:
Some devices do not support PoE power supply.
2
DC 12V
Power input
port
-
Power port. Input DC 12V.
1.2 Framework and Dimension
The following figures are for reference only, which are used to know the device dimension,
please refer to the following figure according to the actual device.
Figure 1-2

ZM111317
2
2 Device Installation
Note:
l The device installation steps may be different due to the different appearance and structure,
please refer to 2.1 according to the actual product.
l Please make sure the installation surface can support 3X’S THE weight of the camera and
the bracket.
2.1 Install Device
Figure 2-1
Please see Figure 2-1 and Figure 2-2.
Step 1
Dig holes on the installation surface (wall or ceiling).
Step 2
Open accessories bag, take out expansion bolt and insert it into the hole you just dug.
Step 3
Open accessories bag, take out installation screws. Tighten the screws to fix the device on the
installation surface (wall or ceiling). You can move device sunshade back and forth. When you
have fixed the device, you must tighten screws on sunshade.
Step 4
Plug external wiring of the device properly.

ZM111317
3
Figure 2-2
Step 5
Use cross screwdriver (in accessories bag) to loosen adjusting screw.
Step 6
Adjust the device in all possible directions, and set its monitoring direction according to the
requirements.
Step 7
Use cross screwdriver to tighten the adjusting screws.
Step 8
Waterproof connector installation for network port; see Figure 2-3 for more details.
Figure 2-3
1. Keep the convex groove outward and install the rubber ring into the network port, keep the
smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of
the waterproof connector.
2. Pull the network cable without clear connector head through main body of waterproof
connector, fixing rubber ring and waterproof locking cover, make the clear connector head of
network cable, and then insert it into the network cable.
3. Put the main body of waterproof connector on the network port and rotate it clockwise to lock
the network port and waterproof connector firmly.
4. Put the waterproof locking cover on the main body of waterproof connector and rotate it
clockwise to lock the waterproof connector and waterproof locking cover firmly.

ZM111317
4
3 Network Configuration
The IP camera defaults to DHCP. If you are connecting directly to NVR the NVR will assign the
IPC an IP address. If you are connecting IPC to XVR or hybrid DVR accepting IP camera or if
camera is connected directly on network router make sure you change to a static IP. NOTE:
ALWAYS CHANGE PASSCODE TO IP CAMERA FOR IMPROVED SECURITY.
3.1 Modify IP Address
IP address can be acquired and modified through our quick configuration tool for the cameras
which are accessed via wired network, it needs to connect wired network to configure wireless
parameters before using wireless network cameras. In this chapter, it will introduce the approach
of modifying IP address via “Quick Configuration Tool”; also, you can modify the IP address in the
network parameters of the WEB interface, please refer to the document link for Config Tool.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same network
segment with computer IP address.
Step 1) Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2) Double click the device to be configured, the system will pop out the “Login” dialog box.
Enter the IP address, user name, password and port number of the camera, and click
“Confirm”.
Note:
The default user name and password are admin and admin respectively, the default of port is
37777. See Figure 3-1 for more details.
Figure 3-1

ZM111317
5
Step 3) Modify the camera IP address on the “Net” interface, click “Save” to finish modification.
See Figure 3-2 for more details.
Figure 3-2
3.2 Login WEB Interface
Note: Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to our website for the latest documentation.
Step 1) Open IE and input the modified camera IP address in the address bar.
Step 2) The login interface is shown below, please input your user name and password (Default
user name is admin and password is admin respectively), click “login”.
See Figure 3-3 for more details.

ZM111317
6
Figure 3-3
Step 3) Install controls according to the system prompt; see Figure 3-4 for the WEB main interface.
Please modify the administrator password as soon as possible after you successfully logged in.
Figure 3-4

ZM111317
7
Note:
l This quick start guide is for reference only. Slight difference may be found in user
interface.
l All the designs and software here are subject to change without prior written notice.
l All trademarks and registered trademarks mentioned are the properties of their
respective
owners.
l If there is any uncertainty or confusion, please contact technical support.
l Please visit our website or contact your local service installer for more information.