ZUUM D4MP-IP-3.3-10.5-IR30-WH User manual
D4MP-IP-3.3-10.5-IR30-WH
IP White Dome Camera 4 Mega Pixel, 3.3-10.5MM Lens, P2P, UPnP, PoE
This is a great full-featured 4 mega pixel IP dome camera. D4MP-IP-3.3-10.5-IR30-WH will work with the ZUUM APP as a
standalone camera, no DVR required for access. You can set it up in seconds with our P2P network. This IP camera also
supports UPnP. You can quickly add to our Hybrid TVR (DVR) without ever setting up in the network router or accessing the
web browser of the camera. Just set mode switch and select open UPnP in the TVR menu and camera will add automatically
to the open network channel you set.
Features:
> 1/3” 4 Mega Pixel progressive scan CMOS camera
> H.264, H.265, MJPEG, 4MP real-time recording
> Supports intrusion detection
> 2D,3D,DNR,DWDR, ROI, Anti-fog, IR-Cut
> Triple Stream, Mobile APP, P2P
> Supports PoE, ONVIF
> TF Card
> Motorized Lens
> IP66 rated for outdoor use
Package Includes:
IP Dome Camera 1 piece
Mounting screw pack x 1 piece
Mounting Template x 1 piece
Weather proof RJ45 Housing x 1 piece
Instructions
Warning:
- Please use the required power supply in accordance of IEC60950-1. Power should comply with rated voltage 12 VDC for
standard power supply connecting to number 7 in diagram below. If connecting by PoE number 6 in diagram below please
make sure it meets the PoE standards.
- Camera is rated at IP66. Camera can withstand rain or moisture based on IP66 rating. Camera is not designed to be
installed in direct rain or submerged into water. Please see the rating chart for details of the IP66 rating.
- Installation of this device should be done by an experienced professional and comply with safety and local regulations.
Attention:
– Before connecting the camera make sure you have selected the correct power supply. Using incorrect power supply will
damage the camera.
- Please do not drop or strike camera to avoid permanent damage.
- Please do not touch the image sensor optical element. If necessary to clean, use a soft clean cloth with alcohol to wipe
dust.
- Avoid pointing camera toward glare such as direct sunlight or bright lights. It will effect picture quality and affect the life of
the product.
- Install in temperature range -14° F ~ + 140°F, and avoid strong electromagnetic radiation etc.
- Maintain ventilation flow around the camera
Factory Reset:
When camera is powered up or restarts hold the “RESET” button (8 in diagram below) for 10 seconds. All parameters of the
camera will be restored to factory default settings, including username, password, IP address, port number etc.
Installation of Camera:
Image 1-1 IPC Interface
No.
Name
1
Audio in
2
Audio out
3
485 interface
4
Alarm in
Alarm out
5
BNC interface
6
10M/100M Ethernet Network Port
7
Power Port
8
Reset key
9
TF card slot
10
232 interface
11
Inner liner
12
Transparent cover
1. Sticker Installation: Take out the attached installation sticker and paste it on the wall according to the marked holes on the
sticker to drill.
2. Remove the front cover and Inner liner:Unscrew the screws of the camera，open the front cover and remove the liner on the
lens, shown in Figure 2-1.
Figure 2-1 Remove the front cover and Inner liner
3. Installation of SD card:Insert the SD card into the SD card slot, shown in Figure 2-2.
Figure 2-2 Install of Micro SD Card
4. Camera Mounting: This camera adopts integrated bracket structure. Please use 3pcs PA4 screws to fix the base of the camera at
the installation location shown in Figure 2-3.
Figure 2-3 IPC Mounting
5. View –angle adjustment: This series camera supports three-axis adjustment. Horizontally rotatable 0-355 °,!Rotation rotatable
0-355 °,!Vertically rotatable 0~75°. As shown in Figure 2-4.
Figure 2-4 View adjustments
6. Lens adjustment: This series camera supports vari-focal lens and motorized lens, for vari-focal lens zooming, zoom focusing
adjustment screw (T~W terminal) select the appropriate viewing angle, and then adjust the focus screw (F~N terminal) so that
the whole picture is clear. After you get the desired picture, then tighten the focusing rod lens. As shown in Figure 2-4.
Figure 2-4 Lens adjustments
7. Complete the installation: Replace the inner cover and the front cover,tighten the cover screws，and finally peel off the
protective film，the installation is completed，as shown in Figure 2-5.
Figure 2-5 Complete the installation
Viewing Camera:
You have a couple ways to view the ZUUM IP camera.
1) FAST WAY and most convenient way when using our IP camera Model: D4MP-IP-3.6-IR20-WH is to connect to our Hybrid
TVR’s by built in switch. Basically plug the IP cameras into the network or POE switch attached to the network so IP
cameras receive power. Then go to your compatible TVR (DVR) and go to the Mode Switch section. This is where you can
determine how many analog cameras and IP cameras can connect to the TVR. So for example on a 4 channel TVR you can
only have 4 cameras total but they can be any mix of analog, HD analog or IP camera. If you will have just one IP camera
connect to the TVR then select which channel that will be in the Mode Switch. After that has been completed then go to
the NET Channel Mgt. section where you will see a list of items on your network. Open UPnP. Once you do that you can
select the IP camera from the list and it will automatically add it to the TVR. In this example DHCP does not have to be on
or any configuration on the IP camera. It is designed to be plug n play using UPnP.
2) The camera is set up as DHCP by default. So if you plug IP camera into your network or router then you can see if it is in
the list when you log onto your router. You can also use other tools to scan your network for device detection like Mobile
apps. (Fing for example). The name of our network interface card (NIC) is Hangzhou Zenointel. This should be the name
you see for our DVR’s and IP cameras. You can also use our ZUUM IPC Update tool to search for cameras on the network
and make firmware updates using this tool like assigning static IP addresses. You can find this tool on our website when
you select Model: D4MP-IP-3.6-IR20-WH under the RESOURCES tab.
Once you have IP address that was assigned via DHCP please enter into your browser. You will then see a log on screen as shown
below. (Default username: admin) case sensitive (Default Password:123456)
The following interface should pop up a link. (Please download the plug-in by clicking here) when you log in. Please click it and
install plug-in then restart your browser to log in.
Model:
D4MP-IP-3.3-10.5-IR30-WH
Sensor
1/3” 4MP Progressive Scan CMOS
Minimum Illumination
Color: 0.05Lux/F1.2, 0 Lux/F1.2 (IR On)
Lens
3.3-10.5mm
IR Distance
Up to 98’ (30 meters)
PoE
Power over Ethernet Capability (yes)
Browser Supported
Windows (IE, Firefox)
Power
12VDC 8W Max
Temperature
Operation: 14˚ to 140˚F
Operation Humidity
10% ~ 90%
Dimensions – Inches
6.07” x 4.76”
Weight – lbs.
2.53
NOTE: If there is an ActiveX Control plug in problem open your Internet Explorer and choose Tools/Internet
Options/Security/Custom Level, then check “Enabled” or Pop Up” under “ActiveX Control and plug-in” and set the security level
lower.
IMPORTANT: When connecting IP cameras to the TVR its best to assign them a static IP. This way if router address changes you
do not have to worry about IP cameras and TVR reconnecting.
Specification:
Do you Need Technical Support?
ZUUM is proud to offer free technical support to ensure your product is operating correctly.
If you are experiencing difficulties setting up this product, please call us for assistance 1-888-861-7351 or visit
www.zuum.life
Here for You 24/7
This manual suits for next models
1
Table of contents
Other ZUUM Security Camera manuals
