ZyXEL Communications OMNI.NET LITE User manual

Omni.Net Lite
ISDN Terminal Adapter
Quick Start Guide
3/2005
Version 1.1
English
Deutsch

Contents
English...................................................................................... 1
Deutsch................................................................................... 17

English
1
Overview
This guide shows you how to connect and access the Internet through your
ISDN Terminal Adapter (TA). You should have an Internet account already
set up.
1. Make the hardware connections.
2. Check top panel LEDs for proper hardware operation.
3. Install your TA driver on your computer to configure the TA.
4. Create a dial-up connection.
5. Dial up a connection.
Installation Requirements
To install the TA, you will need the following:
• Microsoft Windows 95, Windows 98 SE (Second Edition), Windows
Me, Windows 2000 or Windows XP
• 20MB of free disk space for the driver
• A computer with a 25-pin serial port
• An RS-232 cable
• RJ-11 and/or RJ-45 cables
1 Making Hardware Connections
1. Connect your analog phone device(s) to the PHONE 1 and/or PHONE 2
port(s) using RJ-11 cable(s).
2. Connect the TA to the ISDN network using the included ISDN cable.
Connect one end of the RJ-45 cable to the port labeled ISDN and the
other to the ISDN wall jack and/or the NT-1 device. See your User’s
Guide for more information.
3. Connect the female end of the RS-232 cable to the TO DTE port and the
other end to the serial port (such as COM1 or COM2) on your computer.
4. Connect to a power source using the included 16V AC power adaptor.
5. Turn the TA on by flipping the power switch up.

English
2
2 Checking the Top Panel LEDs
Once you have completed all of the installation steps above, turn on the TA.
The TA starts performing system testing, where you should see a series of
LED lights blinking. After this cycle is complete, the PWR and CTS LEDs
should stay on.
If the system testing fails, the LNK LED flashes.
If you have a communication program loaded and active (connected to the
same serial port as your TA), the DTR LED should be on after the system
testing. See your User’s Guide for detailed LED descriptions.
3 Driver Installation
Follow the steps below to install the TA driver that comes with the included
CD. Screens for Windows XP are shown in this guide unless otherwise
specified. The steps in Windows XP refer to the classic start menu and classic
view.
Be sure your computer is already turned on before connecting the RS-232
cable from your TA to your computer. The plug and play function of
Windows detects your new device and shows an installation wizard as shown.
Your computer should automatically detect your new
hardware and display the installation wizard. If it does
not, you may go to Section 3.2 to install your driver
manually. If this does not work, disconnect the RS-232

English
3
cable and restart your computer, then plug the RS-232
cable back in.
3.1 Plug and Play Installation
1. Windows 95/98 SE/Me/2000:
The following screen displays
if Windows detects the TA.
Click Next to continue.
2. Click Next to allow Windows
to display and install from a
list of all the drivers or the
specific location.
3. Insert the included CD into
your CD-ROM drive, click
Have Disk ... and then Browse
to find the INF file in the
Driver folder.
Click OK to return to the
Install From Disk screen and
then click OK to go back to the
Found (Add) New Hardware
Wizard screen.

English
4
4. Click Next to continue.
5. Windows 95/98 SE/Me/2000:
The installation wizard has
found the location of your TA
driver. Click Next to continue.
6. Click Finish to complete the
driver installation.
3.2 Manual Installation
1. Be sure your TA is turned on.
2. Windows XP/2000: Click Start, Settings, Control Panel. Double-click
the Phone and Modem Options icon.
Windows 98 SE/Me: Click Start, Settings, Control Panel. Double-click
the Modems icon.

English
5
3. Windows XP/2000: Click
the Modems tab and the
Add button.
4. Windows 98 SE: Select
Other and click Next.
5. Select Don’t detect my
modem; I will select it
from a list and click
Next to continue.
6. Follow steps 3 and 4 in Section 3.1.

English
6
7. Select which modem and
which port you want to
install and click Next.
8. Click Finish to complete
the driver installation.
4 Creating a New Dial-up Connection
Follow this procedure to set up your dial-up networking connection. Use the
information from your ISP to fill in the wizard screens.
Windows XP
1. Click Start, Programs, Accessories, Communications, New
Connection Wizard.
2. Click Next to continue.

English
7
3. Select Connect to the
Internet and click Next.
4. Select Dial-up connection and
click Next.
5. Select Set up my connection
manually and click Next.
6. Select Connect using a dial-
up modem and click Next.

English
8
7. Select your TA name and click
Next.
8. Enter the name of your ISP for
identification purposes and
click Next.
9. Enter the phone number of
your ISP. Click Next.
10. Enter the user name and
password that your ISP gave
you and click Next.