2DI TV2 Operating manual

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
1

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
2
Congratulations!
Your TV2 with easy touch will provide years of reliable service, collecting, storing and displaying
data while monitoring temperature and relative humidity. Although it is a highly sophisticated
instrument it is easy to install and use.
The Display:
The LCD display is a full color easy touch display. With a simple touch on the display you can
navigate to the menu screens, a temperature history chart for one of the sensors, zoom in or out of a
chart to see more data, set the alarms, silence an alarm, set the data storage rate, etc...
Sensor Accuracy:
The TV2 logs and displays information it receives from its sensors. The accuracy of that data
depends on the sensors. The internal and external thermistor sensors are accurate to ± 0.3°C and
thermocouple sensors are accurate ±1.0° to ±2.2°C depending on the type of thermocouple.
Humidity sensors have an accuracy rate of ±3%. (See the chart on page 4).
Display Power:
The TV2 display is powered via a USB cable from a computer or the wall plug. An optional DC
connector is also available which will accept 5-30 volt dc. Backup batteries (AA) are installed in the
TV2 and will keep it running for about 40 hours if USB power is missing. The batteries can be
replaced by removing the back of the TV2 enclosure (see page ?? ).
Sensor Power:
Wireless sensors are powered by a 9-volt battery with a normally life expectancy of ~ 1 year.
Operating on batteries:
If normal USB power fails and the ‘Missing AC alarm’ is active, the internal buzzer will beep in 1
second intervals for 60 seconds, sleep for 10 minutes, then beep every second for another 60
seconds, etc.. At the same time the TV2 will enter a light sleep mode after 20 seconds to conserve
battery power. The display can be awakened for 20 seconds with a touch.
Note: Repeatedly waking a display running on batteries will shorten the life of the batteries.
Internal Alarm & Relay:
The TV2 has a dry contact normally open (N/O) relay and piezo buzzer, which are activated when
alarm conditions occur.
Factory Service and Returns:
Please call for a return authorization (RA) prior to sending any instrument for repairs. (see page 34
for warranty information).

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
3
Table of Contents
Component and Packing List pg 4
Quick Start pg 5
Sensor Setup pg 6
Setting the Alarms pg 7
Installation Tips pg 8
TV2 Status Screen pg 9
LED & Reset controls pg 10
Navigating with Easy Touch pg 10
Main Menu pg 12
Operational Modes pg 14
Main Mode pg 15
Trace Mode pg 17
Sleep Mode pg 18
Calibration pg 19
TView Software pg 21
Frequently Asked Questions pg 31
Appendix Pg 36
Disclaimers Pg 36
Warranty pg 37
FCC & CE Mark Certifications pg 38

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
4
Component and Packing List
Your TV2 should have come with
1. One or more wireless sensors
2. A 9-volt batteries for each sensor
3. A six-foot USB cable
4. A wall transformer
5. A CD
6. A Quick Start Guide
If any of these items are missing please contact the factory or the distributor/reseller from
whom you ordered the TV2 for a replacement.
Sensor types used by the TV2
ID Type of sensor Range Accuracy
Temperature Only
Digital Sensor Digital wired -20°C to 75°C ± 0.3°C
Thermistor sensors Wired or Wireless -20°C to 75°C ±0.3°C
Thermocouple Above 0°C Below 0°C
E E type wired or wireless -200°C to
870°C ±1.0°C or ±.5% ±1.0°C or ±1%
J J type wired or wireless 0°C to 760°C ± 1.4°C or ±0.75%
T T type wired or wireless -200°C to
370°C ±1.0°C or ±.75%, ±1.0°C or ±1.5%
K K type wired or wireless -250°C to
1260°C ±2.2°C or ±.75% ±2.2°C or ±1.5%
Temperature & Humidity
Thermistor & Humidity Temperature & Humidity
wired or wireless
-20°C to 75°C
0% to 100%
± 0.3°C
± 3.0 %

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
5
Quick Start
Your TV2 can be installed and operating in just a few minutes by following these simple steps.
1. Connect the TV2 to a power supply and touch the LCD.
This display will appear.
2. Touch ‘Up’ or 'Down' to select C° or F° and touch ‘Enter’.
3. Touch ‘Up’ to select the date format (MM/DD/YY, DD/MM/YY or YY/MM/DD) and then
'Enter'. The date format defaults to the US style (MM/DD/YY).
4. Set the day, month, year, hour and minute in the appropriate field by scrolling through the
possible values with 'Up' or 'Down' after moving to the appropriate field with 'Enter'.
(Note: It is possible to move to another field with the ‘Right’ button but your entries will not
be recorded).
5. Touch ‘Escape’. You will be asked to verify that you want to erase all data. Use ‘Right’ to
highlight YES and touch 'Enter'.
6. Touch 'Escape' to return to the previous menu.
The TV2 is now set and operating. Next TV2
will help you setup sensors and alarms

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
6
Setting up sensors
1. Install a 9-volt battery in each sensors.
2. After a few seconds, the TV2 will recognize the sensor and change the display to the Sensor
Setup menu. The hour area of the sample data field will be highlighted.
Note: If the TV2 does not see your sensor you will need to link it.
The linking procedure is found in the FAQ on page 30.
3. This is how often you want the sensor to store a temperature). You may scroll to any value
between 1 min and 24 hrs with 'Up' or 'Down', touching 'Enter' to move to each field, or
accept the default by touching 'Enter'. The default value is ten minutes (00:10:00).
4. Select the type of averaging with 'UP', or 'Down' and touch 'Enter'. There are three possible
selections.
a. Fast – no averaging occurs. The exact measurement at the time of sampling will be
stored and displayed. (Not normally used except during calibration)
b. Medium- some averaging will take place so that minor temperature fluctuations will be
filtered out. (This is the default value).
c. Slow – additional averaging will occur. (Not normally used).
5. Set the chart display (Y axis) with ‘Up’ and ‘Down’.This does not set the alarm. Setting
these values has no effect on the alarm, what data is collected, or what is stored. It simply
sets the upper and lower point of the Y-axis of the temperature chart shown on the TV2. Any
temperature that cannot be displayed on the chart screen because it falls outside these limits
will show as a point at the top or the bottom of the display.
Note: These limits can be adjusted at any time without affecting your data.

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
7
Setting the sensor alarms
6. Set the Alarm by highlighting the ‘Set Alarm’ button and touching ‘Enter’.
7.
8. . Enable the alarm by touching 'Up' and then 'Enter'.
A. Set the trigger-alarm-time to any value between 0:00 and 99:00. This controls how long the
alarm and the relay will be activated.
Note: If you are using a dialer set it for at least 00:30 (30 seconds) but not longer
than 06:00 (Six minutes).
B. Scroll in the upper alarm limit and delay time and then the lower alarm limit and delay with
'Up’ and ‘Down’ touching 'Enter' to move to each field in turn.
Note: The delay time is how long the temperature must remain above the limit before the
alarm occurs.
9. You do not need to enter the Calibration Menu at this time. (For calibration procedures see the
document Entitled ‘Calibration Procedures’ on the CD. It can also be downloaded from our
website http://www.e2di.com/PDFs/Calibration Procedures.pdf)
10. Touch 'Escape' until you return to the Status Screen.
You are done!

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
8
Installation tips
1. Planning - Position the TV2 display close to an AC power source or your computer. The TV2
receives its power via a USB cable, which can be plugged into a computer or a wall
transformer. If you can power the TV2 from your computer you will be able to auto-
download data from the TV2. Auto Downloading data causes the TV2 data to be copied to
your computer every few seconds.
2. Wireless Sensors. Decide where you are going to place each wireless sensor. Each senor has a
transmitter that sends the data to the TV2. The range of the transmitter is 100 feet clear-line-
of-sight. Walls or furniture between the sensors and the TV2 will decrease the range. Use the
signal strength meter on the Status Screen to insure you have adequate reception. Allow three
seconds to elapse after moving a sensor before evaluating the signal strength
3. Power for TV2. Power is supplied through a USB. If you power the TV2 from your
computer the TView software can auto download to your computer, updating the alarm log and
initiating email alerts if alarms occur.
4. Backup Battery - Three AA batteries are installed in the display unit to provide temporary
power during a power outage. If a power outage occurs, the display will go to sleep after 20
seconds to decrease the load on the batteries, however the batteries will eventually run out.
Fully charged batteries will operate the TV2 in sleep mode for ~ 40 hours, depending on how
often you are sampling data.
Frequent power outages can drain the batteries. The icon in the bottom center of the display
showing remaining battery life should be checked frequently. Any time the icon appears less
than 1/3 full, the batteries should be replaced. This is done by removing the six screws on the
back of the display and replacing the three AA batteries with new ones.
Note: If the battery voltage drops too low you will warned to replace the internal battery.
Your stored data will not be affected even if the batteries are completely dead or removed as
all settings and data are stored in non-volatile memory. If a low battery condition does
occur it is recommended that you copy your data to a PC with the TView software as an
extra safety measure.
Operational Tip: If the power to the TV2 is interrupted, an alarm will sound and the relay
will close. This alarm can be disabled on the Main Menu if desired.

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
9
The TV2
The Status Screen
Since the TV2 has an easy touch screen, additional information can be viewed by touching various
'hot spots'.
For example:
1. Touch a temperature to see the history chart for that sensor.
2. Touch a Max/Min area to reset it.
3. Touch 'Main Menu’ to set or change various settings, such as the scale, the temperature
sample rate, high-low alarms for each sensor, etc...
Current temperature. Updated
once a minute.
Max/Min temperature recorded since the last reset.
Appears in red if the reading is above the alarm
threshold
.

Two Dimensional Instruments, LLC •P O Box 159 •Crestwood, KY 40014
[phone] •[phone] fax •[phone] international
10
The LEDs and reset button at the bottom of the display
The green LED blinks once a second, indicating the
display is collecting data and working normally.
Even during a power outage this LED will continue
to blink, indicating that it is collecting and storing
temperatures from the sensors
The Red LED blinks when the display is operating
on batteries. If an alarm occurs it will glow a
steady red.
The small hole on the left of the red and green LEDs is a reset button. Insert the paper clip slowly
until you feel the button press down. It will pop back up as soon as you release the paper clip and a
system reset will occur. (Your settings and data will be preserved).
Navigating with Easy Touch
Where to touch
Touch any temperature to see a
temperature history chart for that sensor.