2E GAMING G2723BV User manual

Q2712RUCLCDUserManual
LCD
MONITOR
СВІТЛОДІОДНИЙ
МОНІТОР
СВЕТОДИОДНЫЙ
МОНИТОР
G2723BV
User Manual
 
 
Read this manual carefully before use.
    .
    .
www.2egaming.com

 2 
EN
Content
WARNINGS/SAFETY PRECAUTIONS
WARNINGS
ATTENTION
Important safety instructions
OPERATING INSTRUCTIONS
Components and auxiliary equipment
Power settings
ASSEMBLY INSTRUCTIONS
FUNCTIONALITY
MONITOR OPERATION
OSD MENU
Screen
Color
Gaming
Enter
System
Users
Specifications
Troubleshooting
Additional information
Warranty
3
3
3
4
5
5
5
5
5
7
7
8
8
9
9
9
10
10
11
11
32

 3 
EN
Warnings/Safety precautions
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNINGS/SAFETY PRECAUTIONS
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER AND BACK PANEL THERE
ARE NO USER-SERVICEABLE PARTS
INSIDE.
I CASE OF DAMAGE OR ERROR REFER SERVICING
TO QUALIFIED PERSONNEL.
Lightning flash with arrowhead symbol
within an equilateral triangle is intended
to alert the user to the presence of
non-insulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock in case of improper
usage of the product.
Exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance instructions in the literature
accompanying the product.
WARNING:
Do not put the monitor in rainy or foggy places to prevent from fire or electric shock.
To prevent scratches or damages to the LCD screen, do not knock, apply or rub the surface with sharp
or hard objects or stiff cloths as well as try not to touch the LCD screen with your hands.
Any modifications to this product that have not been clearly and explicitly approved in advance by the
manufacturer responsible for compliance with these regulations are forbidden.
ATTENTION:
Excessive sound pressure from earphones and headphones can cause hearing loss.

 4 
EN
Important safety instructions
1. Please read and understand this manual before use.
2. Do not throw this manual away after reading.
3. Immediately pull out the plug from the adapter/socket, if you hear an unusual, extraneous sound
or feel an unpleasant smell when connecting and turning on the monitor; if the monitor does not
display an image, then be sure to contact the service or technical center.
4. Keep the monitor away from moisture, splashes and rain as much as possible, avoid getting dust
inside to prevent the risk of electric shock or short circuit. Do not cover the ventilation openings of
the device. Do not cover the monitor with cloths, do not place near curtains, newspapers, etc.
5. Make sure the monitor is not placed near heating objects or in direct sunlight. Provide the monitor
with access to ventilation. The distance between the monitor and other devices or the walls of the
cabinet, where it is built in, should be at least 10 cm.
6. You can clean the display only with a soft, clean cloth, after turning it off and pulling the plug from
the outlet. Do not rub or press the screen while cleaning, don’t scratch or hit the screen with hard,
heavy objects.
7. Do not wipe the monitor with gasoline, chemical or alcohol-based products, as this can damage
both the screen itself and its case.
8. Do not install the monitor on unstable surfaces.
9. Protect the power cord from constant stepping on and tripping over it, as well as kinks, especially
at the point of connection with the plug, sockets and at the points of connection of the power cord
with the device.
10. Disconnect the device from the electrical network during a thunderstorm or if the device is not
used for a long time.
11. If the device, power cable or plug is damaged, as well as if the device has been exposed to liquids
or moisture, has been mechanically damaged and does not work properly, contact an authorized
service center.
12. Do not expose this device to liquids, splashes of water, or place containers filled with liquids on the
device.
13. Do not open the lid or back of the device, as all parts inside are live and may cause electric shock.
There are no user serviceable parts inside. All internal adjustments and repairs should be performed
only by qualified personnel.
14. Do not place open flame sources such as candles near/on the monitor. Please be sure to remove
the plug from the outlet and contact service center, if foreign objects or water have entered the
monitor.

 5 
EN
４５
４５
Operating Instructions
Components and auxiliary equipment
Before assembly and installation, check the availability of all components.
Power settings
Direct current: 12V, 4.5A. External power source - alternating current: 100-240V ~50/60 Hz 1.5A
Check the technical settings of the device indicated on the label on the back of the device.
Monitor
Power cord
Stand base
DP cable (Display Port)
Microfiche and power
requirements label
User manual
４５
PSU
Functionality
Manufacturer’s statement: This manual is a general reference manual. The appearance of
the actual product may differ from the images.
HDMI HDMI input
DP (Display Port) Display Port input
Earphones Headphone output
DC input 12V DC 12V 4.5 power input

 6 
EN
Assembly instructions
1. Insert the rack into the base of the stand and fix with two M4*16 bolts.
2. Insert the assembled stand into the hole on the back wall of the monitor as far as it will
go in the direction indicated by the arrow; then press down and clockwise.
To detach (if necessary) the stand from the monitor, do the following:
1. Press the slider near the VESA mounting on the back lid of the monitor;
2. Turn the stand counterclockwise and pull it towards you;
3. Tilt the base in the direction of the arrow and pull it out.
6 Note:Someofthecontentsinthismanualmaydifferslightlyfromthefinalproduct,andthelatershallbereferredto.6.InstructionofBaseInstallation①InsertthebaseintothesupportandlocktwoM4*16screws.②Insertthewholebaseinclinedlyintothebackshellagainsttheholeinthedirectionofthearrow;Thenpressdownclockwise.Toremovetheentirebase,performthefollowingsteps.①PushthesliderneartheVESAcoverofthebaseupward;②Rotatethewholebasecounterclockwiseupward;③Tiltthebaseinthedirectionofthearrowandpullitout.Step1Step2
Step1Step2
6 Note:Someofthecontentsinthismanualmaydifferslightlyfromthefinalproduct,andthelatershallbereferredto.6.InstructionofBaseInstallation①InsertthebaseintothesupportandlocktwoM4*16screws.②Insertthewholebaseinclinedlyintothebackshellagainsttheholeinthedirectionofthearrow;Thenpressdownclockwise.Toremovetheentirebase,performthefollowingsteps.①PushthesliderneartheVESAcoverofthebaseupward;②Rotatethewholebasecounterclockwiseupward;③Tiltthebaseinthedirectionofthearrowandpullitout.
Step1Step2
Step1Step2

 7 
EN
Monitor operation
Button (mini joystick) Function
Description of the device control buttons
Up
Down
Left
Right
Short press
Down/Up
Left
Right
Pressing for 3 s
6 Note:Someofthecontentsinthismanualmaydifferslightlyfromthefinalproduct,andthelatershallbereferredto.6.InstructionofBaseInstallation①InsertthebaseintothesupportandlocktwoM4*16screws.②Insertthewholebaseinclinedlyintothebackshellagainsttheholeinthedirectionofthearrow;Thenpressdownclockwise.Toremovetheentirebase,performthefollowingsteps.①PushthesliderneartheVESAcoverofthebaseupward;②Rotatethewholebasecounterclockwiseupward;③Tiltthebaseinthedirectionofthearrowandpullitout.Step1Step2Step1Step2
33.OperationofDisplayTheOSDcontrolbuttonsareshownasthefigure.Modelsofthesameproductseriesareonlydifferentinbuttonpositionandpanelpattern,pleaserefertothepracticalmodel.
PowerindicatorlightRocker
3.3SafetyprotectionWhenthevideosignalsofPCexceedsthefrequencyrangeofthedisplay,thehorizontalandfieldsynchronizingsignalswillbeshutdowntoprotectthedisplay.Then,youhavetosetthePCoutputfrequencytoanacceptablerangesoastomakethedisplayworknormally.3.1PowerindicatorlightWhenthedisplayisworkingnormally,theblueindicatorlightison;whenitisintheenergysavingstate,theindicatorlightblinkswithredcolor;whenthesignalsaresentagainintheenergysavingstate,themachinewillreturntonormalwork;Afterthedisplayisturnedoff,theindicatorlightisoff.Asthedisplayisstillpoweredundertheshutdownstate,forthesakeofsafety,thepowercordshouldbeunpluggedwhenthedisplayisnotused.3.2IntroductiontorockerfunctionsEnterthefunctionmenu:SignalsourceinputGameplusshortcutkeyPresetShortcutkeyShortpresstoturnonthemachine/Openmenu,pressandholdfor3stoturnoffthemachineVolumeadjustmentshortcutkeyRockerUpRockerLeftRockerRightPressRockerRockerDownSamemenusingledirectionupmove/AdjustvalueSamemenusingledirectiondownmove/AdjustvalueReturntothepreviousmenuEntertothenextmenuShortpresstoClosemenu,/pressandholdfor3stoturnoffthemachineRockerUpRockerLeftRockerRightPressRockerRockerDownInitialstate:
Select the signal source
Adjust the volume
Quick access to Game Plus settings
Access to quick settings
Enter/Exit in the settings menu
Navigation by menu items; change settings
Return to the previous menu page
Go to the next menu page
Turn off the monitor

 8 
EN
OSD menu
SCREEN
In this section of the menu, you can adjust
the brightness, contrast and other display
modes of the monitor.
BRIGHTNESS - This setting adjusts the
balance of dark colors in the image. If the
setting value is too high, the image will be
blurred. If the setting value is adjusted too
low, the image will be too dark and will not
have clear outlines.
CONTRAST - This setting adjusts the white
balance of the image. If the setting value is too high, the image will be too bright and will not have clear
outlines. If the setting value is adjusted too low, the image will be blurred.
BLACK LEVEL/BLACK EQUALIZE - Allows you to adjust the brightness and contrast of the screen to
display dark areas of the image.
PRESET -This setting has several standard display modes: Standard, User, Movie, Photo, RTS, FPS1, FPS2
ASPECT RATIO - Allows you to choose one of the format options for the image on the screen: Full screen,
16:9 or 4:3.
SHARPNESS - The setting allows you to adjust the sharpness of the image displayed on the screen.
COLOR
The section contains settings for
adjusting the temperature, hue,
saturation of the displayed colors, as well
as other settings.
COLOR TEMPERATURE - This setting
allows you to select one of the preset color
settings: Warm / Normal / Cool / sRGB /
User.
GAMMA - the coecient setting of
gamma correction of the image.
HUE - Variety of any color that diers from the main one in greater or lesser brightness and intensity. This
setting allows you to change the shade of the image.
SATURATION - This setting allows you to make colors brighter or more mued.
BLUE FILTER - Cuts o part of the blue color, promotes comfortable long-term work.

 9 
EN
OSD menu
GAMING SETUP
FREE SYNC/GSYNG supports an
increased refresh rate aimed at reducing
screen lag.
OVER DRIVE - Allows you to increase
the response speed of the matrix (pixel
transition time) to reduce the displacement
/ doubling of fast-moving objects.
Game Plus is the settings of additional
parameters for use in games:
- Timer, Scope, FPS Counter
HDR (High Dynamic Range) - Thanks to
HDR technology, white color becomes brighter and black becomes deeper. This makes the image on the
monitor more realistic. The following modes are available: On / Automatic / O.
DYNAMIC CONTRAST (DCR) - Allows you to automatically adjust the brightness and contrast of the screen
to display darker areas of the image.
INPUT
In this section, you can select the port
through which the input video signal will
be sent to the monitor:
DP - Sets the DP1 or DP2 port as the
monitor’s video source.
HDMI - Sets the HDMI port as the monitor’s
video source.
SYSTEM SET
In this section, you can choose the menu
language, adjust the sound volume, menu
view, and reset the settings to factory
defaults.
LANGUAGE - This setting allows you to
select the OSD language from the list.
OSD SETUP - Changes the OSD menu
display settings:
- G-MENU POSITION - The function allows
you to adjust the horizontal position of the
OSD menu.
- V-MENU POSITION - The function allows you to adjust the vertical position of the OSD menu.
- TIMER - The function allows you to set the time during which the menu will be displayed before its
automatic closing.
- TRANSPARENCY - This setting helps to adjust the transparency of the OSD menu.
AUDIO - Turns o the sound on the headphone output.
RESET - In this section, you can automatically adjust the main image settings and reset all the default settings.

 10 
EN
OSD menu
USERS DATA
In this section, you can save OSD settings
for three users.
Specifications
Model G2723BV
Screen size 27’’
Matrix type VA CURVED R1500
Aspect ratio 16:9
Viewing angles 178 °/ 178 °
Number of displayed colors 16.7M
Resolution 2560x1440
Refresh rate 165 Hz
Response time 2.7 ms
Brightness 300 cd/m2
Contrast 4000:1
Interfaces xDP, HDMI, Audio out
DP 1.2: 2560X1440 / 165 Hz
HDMI: 2560X1440 / 144 Hz
Built-in speakers No
Screen tilt 15°/5°
Height adjustment range No
Screen rotation (portrait mode) No
Power consumption in operating mode <54 W
Power consumption in standby mode ≤0.5 W
Monitor power supply settings DC 12 V, 4.5A
External power adapter settings AC 100-240 V, 50/60 Hz, 1.5 
Wall mounting VESA 100x100
Package dimensions 690 x 170 x 465 mm
Weight (NET/GROSS): 4.7 kg/ 6.5 kg
Additional Information Free-Sync (G-Sync), HDR, Game plus, Low Blue Light, Flicker Free
Frequency