2Y-LINK PF068A12 User manual

1
Push Fit Mixer
- Work with Intelligent model Signal Processors
- For camera with power rating up to 680mA/8W
- 12 & 24 power voltage for camera are available
- Easy installation with Push-Fit Terminals
- Output to camera without voltage drop
- Support Multi-system video formats
- NO polarity restriction
- Good immunity to electromagnetic Interference
- Mounting plate available for Junction/Back Box fitting
- PF068A12 Universal Mixer (0-500m, 12 to camera)
- PF068B12 Universal Mixer (500-1000m, 12 to camera)
- PF068C12 Universal Mixer (1000-1500m)
- PF068A24 Universal Mixer (0-500m, 24 to camera)
- PF068B24 Universal Mixer (500-1000m, 24 to camera)
-
1: Power to Camera (Push Fit Terminals)
2: 2 Wire to Signal Processor (Push Fit Terminals)
3: Power Stabilizer Terminal
4: Camera Video (BNC Female plug)
User Guide
Overview
Features
Mixers

2
Connect with Signal Processor and Camera as shown in this diagram
Connection Diagram
Fitting with Mounting Plate (MIX-MP)

3
• The following table shows the necessary wire gauge for twin bell wire
over the expected length between camera and T Monitor.
150mA
12V 24V
PF068A1
2
PF068
B
12
PF068A
24
PF068
B24
AWG20
≤ 500m 500~1000m ≤ 500m 500~1000m
CAT5
≤ 500m 500~700m ≤ 500m 500~600m
250mA
12V 24V
PF068A1
2
PF068
B
12
PF068A
24
PF068
B24
AWG20
≤ 500m 500~1000m ≤ 500m
CAT5
≤ 500m 500~600m ≤ 200m
350mA
12V 24V
PF068A1
2
PF068
B
12
PF068A
24
PF068
B24
AWG20
≤ 500m 500~800m ≤ 200m
CAT5 ≤400m
≤ 100m
500mA
12V 24V
PF068A1
2
PF068
B
12
PF068A
24
PF068
B24
AWG20
≤ 500m ≤ 50m
CAT5 ≤200m
680mA Local Power for Camera
(see Note 2 & 3)
12V 12V 24V
PF068A12
PT068A12
PF068A12
PT068A12
PF068B12
PT068B12
PF068C12
PT068C12
PF068A24 PF068B24
AWG20
≤ 200m ≤ 500m 500-900m
900-1200m
≤ 500m 500~1000m
CAT5
≤ 100m ≤ 500m 500-900m
900-1500m
≤ 500m 500~1000m
Wiring Notes

4
Notes :
1. For cameras with operation current up to 680mA and transient peak current up to
1000mA, also a PS-10KU power stabilizer is normally required.
2. For camera power over 8W and/or covering extended distances, local power supply
for camera is required.
3. If local power is needed for camera and ground level difference effect occurs, the
Ground Loop Isolator (PF-ISO/PT-ISO) can be installed together with Mixer to
eliminate electrical noise and hum.
4. For camera power range 9-16W (1300mA/12 DC), High Power Model (Signal
Processor : CI-01-ASP-DI, Mixer : PF150A12D) can be used. [ NO local power for
camera]
ideo input : 1 p-p 75-ohm
Power Supply : 48 DC .Max
Operating temperature : -10°C ~ + 50°C
Dimensions : 65mm x 35mm x 32mm
Suitable for any Camera with following specification:
Each Camera Rating : 12 & 24 , 8W. Max.
Each Camera ideo output : 1 p-p 75-ohm
Specification
PF
-
ISO
PT
-
ISO