3Jtech NetCAMit User manual

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
netCAMit
User’s Guide
Version: 1.0.0.2
Date: October 30, 2008
3JTech Co., Ltd.
2F, No. 342, Fu-Shing N. Rd.
Taipei, Taiwan
Tel: [phone]
e-mail: [email protected]

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
2
Revision History
Version Date Changes
1.0.0.0 October 09, 2007 First Release of netCAMit User’s Guide
1.0.0.1 December 12, 2007 Add the description of advanced network settings in Appendix B
1.0.0.2 October 30, 2008 Remove the description about Trigger In / Out connectors

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
3
Table of Contents:
Revision History ------------------------------------------------------- 2
TABLE OF CONTENTS: ------------------------------------------------- 3
CHAPTER 1. PRODUCT OVERVIEW ---------------------------------------- 4
1.1 INTRODUCTION ----------------------------------------------------- 4
1.2 FEATURES -------------------------------------------------------- 4
1.3 PACKAGE CONTENTS ------------------------------------------------- 4
CHAPTER 2. PHYSICAL DESCRIPTION-------------------------------------- 5
2.1 PANELS ---------------------------------------------------------- 5
2.1.1 Front Panel --------------------------------------------------- 5
2.1.2 Rear Panel ---------------------------------------------------- 5
2.2 ILLUSTRATION ----------------------------------------------------- 6
2.2.1 Front Panel Information ------------------------------------------ 6
RJ45 Network Connector -------------------------------------------- 6
RJ22 Power Supply Connector ---------------------------------------- 6
Lens ----------------------------------------------------------- 6
RFIO Slot-------------------------------------------------------- 7
2.2.2 Real Panel Information ------------------------------------------- 7
Serial Number / Camera ID / Firmware version --------------------------- 7
CHAPTER 3. ASSEMBLING CAMERA --------------------------------------- 8
3.1 MOUNTING METHODS ------------------------------------------------ 8
CHAPTER 4. RESET DEFAULT--------------------------------------------10
APPENDIX A – TECHNICAL SPECIFICATIONS --------------------------------11
APPENDIX B – ADVANCED NETWORK SETTINGS -----------------------------12

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
4
1. Product Overview
1.1 Introduction
netCAMit is a Plug & Play IP camera with a CMOS image sensor as well as built-in IP address,
Ethernet Software Stacks and Protocols. Plug netCAMit directly to a RJ45 Ethernet port and watch
the camera site from anywhere around the world. Connecting directly to Ethernet networks,
netCAMit is a standalone digital network camera requiring no server at the camera site. Through
the trigger in/out functions, netCAMit will provide a complete security solution for you with the
easiest installation.
1.2 Features
yLow cost, DIY security camera – Simple installation and multiple mounting methods
yNo computer is needed at monitored site
yUp to 8 users concurrently browsing the same camera
yStandard JPEG image format
yTrigger-in connector for connecting external sensor for extra security
yTrigger-out connector to alert other external device such as alarms
yTwo-level password protection
yOptional security accessories package, including powerBox, RFIO, RF sensor and contact
sensor for the wired/wireless trigger-in
1.3 Package Contents
─ 1 x netCAMit camera
─ 1 x CD with setup software, user’s manual and quick installation guide
─ 1 x RJ45 Ethernet cable
─ 1 x Power adapter
─ 1 x Desktop / Wall & Ceiling mount

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
5
2. Physical Description
The following information contains the physical description of netCAMit camera. This includes the
functions and the locations of each connector and indicator. The information provides useful
reference when installing the product. Please familiarize yourself with netCAMit cameras.
2.1 Panels
2.1.1 Front Panel
For more related description, please refer to the Section 2.2 and Section 2.2.1.
2.1.2 Rear Panel
For more related description, please refer to the Section 2.2 and Section 2.2.2.
5
3
2
1
6
7
4

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
6
2.2 Illustration
No. in
Figures Name on netCAMit Description Remark
1 RJ45 network
connector To connect to the camera and Ethernet port via RJ45 cable Refer to section 2.2.1 for front panel information
2 RJ22 power supply connector To connect to the camera and power adaptor via RJ22
interface
Refer to section 2.2.1 for front
panel information
3 Lens 300k pixels CMOS sensor Refer to section 2.2.1 for front
panel information
4 RFIO slot To install the optional RFIO
device
Refer to section 2.2.1 for front
panel information
5 SW_1 Press SW_1 button, then netCAMit will perform the
power reset N/A
6 SW_2 Press and hold SW_2 button
for 5~10 seconds to reset the
camera to its factory defaults
The green indicator LED of RJ45
port will light when it is finished
with the reset procedure
7 Camera
information Serial number, camera ID and firmware version Refer to section 2.2.2 for real panel information
2.2.1 Front Panel Information
RJ45 Network Connector
netCAMit is designed for 10/100Mbps Ethernet networks. netCAMit connects to the network via
category 5 cable.
RJ22 Power Supply Connector
netCAMit adopts unique RJ22 cable for power supply. The special featured RJ22 cable includes
Input / Output (I/O) function. Simply connect the Input / Output cable to the desired device and no
hardware jumper fixing on camera is required.
Lens
netCAMit box includes a standard 60° wide angle lens fixed to the camera. Other types of lens are
also available upon request. Please note that different price may apply to different lenses.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
7
RFIO Slot
Plug the optional RFIO device for the wireless trigger-in.
2.2.2 Real Panel Information
Serial Number / Camera ID / Firmware version
The label sticker includes the serial number, camera ID and the firmware version of the camera.
NOTE:
If you have updated the camera firmware version, the firmware version information may no longer
be valid.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
8
3. Assembling Camera
netCAMit is designed for users to mount in three methods, including desktop, ceiling and wall (see
the following figures). Please use the desktop strut or wall & ceiling strut separately to mount the
camera based on your needs. The desktop strut is used for desktop mounting only, and the wall &
ceiling strut is suitable for desktop, ceiling and wall mounting. The figures and description provided
in the following section will assist you in assembling and installing the camera correctly. It is
recommended to configure the camera before positioning the camera. The default method is the
desktop mount with desktop strut.
Desktop Mount Wall Mount Ceiling Mount
3.1 Mounting Methods
netCAMit comes with a desktop mount as the default purchase. If users would like to adopt wall &
ceiling mount, please follow the steps below. Procedures of ceiling mounting are the same as the
ones of wall mounting. The difference between these two mounting methods lies in the position of
screwing. Here we only take the wall mount of netCAMit for example to demonstrate the mounting
method.
(1) First, please unscrew and remove the desktop strut in advance.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
9
(2) Assemble the wall & ceiling strut coming with the package, and then fasten the
camera with the screw on the BACK of the camera. (For the ceiling mount, you should
fasten the camera with the screw on the TOP of the camera.
(3) Link and lock the base coming with the package and strut together.
(4) Before positioning the camera, please drill the wall at the desired position and screw the
fixed board. Then, hang the camera on the fixed board along the slot of the bottom.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
netCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.)
10
4. Reset Default
netCAMit provides “Reset Power” and “Reset Default” buttons that will be easy for users to reset
the camera. The buttons locate in the back of the camera (See 1and 2 of the figure below).
No. in
Figures Name on netCAMit Description Remark
1 SW_1 Press SW_1 button then
netCAMit will do the power reset. N/A
2 SW_2
Press and hold SW_2 button for
5~10 seconds to reset the
camera to its factory defaults
The green indicator LED of RJ-45
port will light when it is finished with
the reset procedure.
Default Setting for netCAMit:
1) DHCP
2) If IP is not assigned within 30 seconds, the default IP then will become: 192.168.8.99:8299
3) Public password: blank
4) Supervisor password: blank
1
2