3Jtech wifiCAMit User manual

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
wifiCAMit
User’s Guide
Version: 1.0.0.2
Date: July 08, 2008
3JTech Co., Ltd.
2F, No. 342, Fu-Shing N. Rd.
Taipei, Taiwan
Tel: [phone]
e-mail: [email protected]

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
2
Revision History
Version Date Changes
1.0.0.0 October 05, 2007 First Release of wifiCAMit User’s Guide
1.0.0.1 December 21, 2007 Add the description of advanced network settings in Appendix B
1.0.0.2 July 08, 2008 Remove all of the description on Trigger In / Out connector

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
3
Table of Contents
Revision History ------------------------------------------------------- 2
TABLE OF CONTENTS-------------------------------------------------- 3
CHAPTER 1. PRODUCT OVERVIEW ---------------------------------------- 4
1.1 INTRODUCTION ----------------------------------------------------- 4
1.2 FEATURES -------------------------------------------------------- 4
1.3 PACKAGE CONTENTS ------------------------------------------------- 4
CHAPTER 2. PHYSICAL DESCRIPTION-------------------------------------- 5
2.1 PANELS ---------------------------------------------------------- 5
2.1.1 Front Panel --------------------------------------------------- 5
2.1.2 Rear Panel ---------------------------------------------------- 5
2.2 ILLUSTRATION ----------------------------------------------------- 6
2.2.1 Front Panel Information ------------------------------------------ 6
RJ45 Network Connector -------------------------------------------- 6
RJ22 Power Supply Connector ---------------------------------------- 7
Lens ----------------------------------------------------------- 7
Antenna---------------------------------------------------------7
Wire/ Wireless Switch ---------------------------------------------- 7
RFIO Slot-------------------------------------------------------- 7
2.2.2 Rear Panel Information------------------------------------------- 7
Serial Number / Camera ID / Firmware version --------------------------- 7
2.2.3 LED Description on the Rear Panel --------------------------------- 8
CHAPTER 3. ASSEMBLING CAMERA --------------------------------------- 8
3.1 MOUNTING METHODS ------------------------------------------------ 9
CHAPTER 4. RESET TO DEFAULT-----------------------------------------11
APPENDIX A – TECHNICAL SPECIFICATIONS --------------------------------12
APPENDIX B – ADVANCED NETWORK SETTINGS -----------------------------14

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
4
1. Product Overview
1.1 Introduction
wifiCAMit is a Plug & Play wireless IP camera with a CMOS image sensor as well as built-in IP
address, Ethernet Software Stacks and Protocols. Plug the wifiCAMit directly into an RJ45 Ethernet
port of network devices with RJ45 cable or use wireless network 802.11b / 802.11g to watch the
camera site from anywhere around the world. Connecting directly to Ethernet networks, wifiCAMit
is a standalone digital network camera requiring no server at the camera site. wifiCAMit will provide
a complete security solution for you with the easiest installation.
1.2 Features
yLow cost, DIY security camera – Simple installation and multiple mounting methods
yNo computer is needed at monitored site
yUp to 8 users concurrently browsing the same camera
yStandard JPEG image format
yTwo-level password protection
yOptional security accessories package, including powerBox, RFIO, RF sensor and contact
sensor for the wired/wireless trigger-in
1.3 Package Contents
─ 1 x wifiCAMit camera
─ 1 x CD with setup software and user’s manual
─ 1 x RJ45 Ethernet cable
─ 1 x Desktop / Wall & Ceiling mount

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
5
2. Physical Description
The following information contains the physical description of wifiCAMit camera. This includes the
functions and the locations of each connector and indicator. This information provides useful
reference when installing the product. Please familiarize yourself with wifiCAMit cameras.
2.1 Panels
2.1.1 Front Panel
For more related description, please refer to the Section 2.2 and Section 2.2.1.
2.1.2 Rear Panel
For more detailed description, please refer to the Section 2.2 and Section 2.2.2.
5
2
1
10
7
4
3
6
8
9

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
6
2.2 Illustration
No. in
Figures Name on wifiCAMit Description Remark
1 RJ45 network
connector To connect to the camera and Ethernet port via RJ45 cable Refer to section 2.2.1 for front panel information
2 RJ22 power
supply connector To connect to the camera and power adapter via RJ22
interface
Refer to section 2.2.1 for front
panel information
3 Lens 300k pixels CMOS sensor Refer to section 2.2.1 for front
panel information
4 Antenna For wireless access Refer to section 2.2.1 for front
panel information
5 Wire/Wireless
switch
To change the wired or
wireless mode for wifiCAMit Refer to section 2.2.1 for front panel information
6 RFIO slot To install the optional RFIO
device Refer to section 2.2.1 for front panel information
7 SW_1 Press SW_1 button, then
wifiCAMit will perform the
power reset N/A
8 SW_2 Press and hold SW_2 button
for 5~10 seconds to reset the
camera to its factory defaults
The green indicator LED of RJ45
port will light when it is finished
with the reset procedure
9 Camera
information Serial number, camera ID and firmware version Refer to section 2.2.2 for real panel information
10 LED To display the status of the
camera in wired or wireless
mode
Refer to section 2.2.3 for LED
description on the rear panel
2.2.1 Front Panel Information
RJ45 Network Connector
wifiCAMit is designed for 10/100Mbps Ethernet networks. wifiCAMit connects to the network via
category 5 cable.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
7
RJ22 Power Supply Connector
wifiCAMit adopts unique RJ22 cable for power supply. The specifications of wifiCAMit’s power
adapter are as follows:
Input: 100 ~ 240V AC, 50/60Hz
Output: 5V DC / 1A
Lens
wifiCAMit box includes a standard 75° wide angle lens fixed to the camera. Other types of lens are
also available upon request. Please note that different price may apply to different lenses.
Antenna
Support WEP and WPA modes for wireless access.
Wire/ Wireless Switch
To switch the wifiCAMit camera into the wired or wireless mode, please push the switch up for
wireless mode or down for wired mode.
RFIO Slot
Plug the optional RFIO device for the wireless trigger-in.
2.2.2 Rear Panel Information
Serial Number / Camera ID / Firmware version
The label sticker includes the serial number, camera ID and the firmware version of the camera.
NOTE:
If you have updated the camera firmware version, the firmware version information may no longer
be valid.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
8
2.2.3 LED Description on the Rear Panel
Mode Color Status
Wired(LAN) Red Off when +5V DC power is turning on.
Lit when the device works normally.
Blinks when getting the SSID and password of the DHCP2WIFI router.
Wireless Red
Off when failing to connect with the Access Point / router.
Lit when the connection with the Access Point / router is successful
and the device works normally.
Blinks when any traffic is present.
3. Assembling Camera
wifiCAMit is designed for users to mount in three methods, including desktop, ceiling and wall (see
the following figures). Please use the desktop strut or wall & ceiling strut separately to mount the
camera based on your needs. The desktop strut is used for desktop mounting only, and the wall &
ceiling strut is suitable for desktop, ceiling and wall mounting. The figures and description provided
in the following section will assist you in assembling and installing the camera correctly. It is
recommended to configure the camera before positioning the camera. The default method is the
desktop mount with desktop strut.
Desktop Mount Wall Mount Ceiling Mount

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
9
3.1 Mounting Methods
wifiCAMit comes with a desktop mount as the default purchase. If users would like to adopt wall &
ceiling mount, please follow the steps below. Procedures of ceiling mounting are the same as the
ones of wall mounting. The difference between these two mounting methods lies in the position of
screwing. Here we only take the wall mount of wifiCAMit for example to demonstrate the mounting
method.
(1) First, please unscrew and remove the desktop strut in advance.
(2) Assemble the wall & ceiling strut coming with the package, and then fasten the
camera with the screw on the BACK of the camera. (For the ceiling mount, you should
fasten the camera with the screw on the TOP of the camera.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
10
(3) Link and lock the base coming with the package and strut together.
(4) Before positioning the camera, please drill the wall at the desired position and screw the
fixed board. Then, hang the camera on the fixed board along the slot of the bottom.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
11
4. Reset to Default
wifiCAMit provides “Reset Power” and “Reset Default” buttons that will be easy for users to reset
the camera. The buttons are located on the back of the camera (See 1and 2 of the figure below).
No. in
Figures Name on wifiCAMit Description Remark
1 SW_1 Press SW_1 button then
wifiCAMit will do the power reset. N/A
2 SW_2
Press and hold SW_2 button for
5~10 seconds to reset the
camera to its factory defaults.
The green indicator LED of RJ45
port will light when it is finished with
the reset procedure.
Default Setting for wifiCAMit:
1) DHCP
2) If IP is not assigned within 30 seconds, the default IP then will become: 192.168.8.99:8299
for wired mode.
3) Public password: blank
4) Supervisor password: blank
2
1

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
12
Appendix A – Technical Specifications
zAdvanced 120 MIPS RISC processor( build in 64kB Flash program memory and 20kB SRAM
data/program memory)
z4M x 16bits SDRAM
zLens:
Focal Length:3.6 mm
Aperture: F 2.0
Angle of View (DIA): ~75 degrees
zRJ22 for 5V DC /100~240V AC adapter
zImage Sensor Specification:
1/4” CMOS Sensor
QCIF, QVGA and VGA
30 frames/sec
Dynamic range: 60 dB
Sensitivity: 3.0 V/LUX-Sec
zTrigger input: Normal Close to Open or Low to High TTL level
zPower consumption: 5V DC/ 750 mA
zInternational Image Standard
640x480, 320x240, 176x144
z24bit Colored Motion JPEG images
zFrame/Sec. ( In wired mode):
640x480 @ 3+frames
320x240 @ 6+frames
176x144 @ 7+frames
zWireless Operation Mode:
Ad Hoc / Infrastructure
zEncryption Type:
WEP (5ASCII / WEP 13 ASCII), WEP (10 HES / 26 HEX)
WPA / TKIP, WPA / AES
zOperating Environment:
Temperature 0~55oC
Humidity 80% relative at 25oC
zNetwork Protocol:
UDP, TCP/IP, HTTP, NTP, DHCP, ARP, etc.
Automatically switch between 10/100baseT/TX Fast Ethernet
Customized Network communication protocol for avoiding hackers

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
13
zWeight: 150g (without the stand)
zDimension of Main Body: 60 x 45 x 100 mm (without the stand)
Note: Any specification is subject to change without any notice.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
14
Appendix B – Advanced NetworkSettings
If you are not using a router, very likely you are using a DSL modem with PPPoE for single PC or
multiple PCs. If your Internet allows only one IP or has no more spare IP from PPPoE, you would
need to buy a new router. If your PPPoE still have a spare IP, you could setup PPPoE for the
camera.
Set up a new router
Find out the type of your WAN port of your Internet service: fixed IP, DHCP or PPPoE. (Please ask
your Internet Service Provider for the connection details and information). Setup the new router
according to the manual comes with the new router. After your PC connected to the new router is
able to connect to the Internet, please follow the Quick Installation Guide for wifiCAMit to set up
your camera.
Set up PPPoE for the camera
Please follow the steps below to set up your PC:
1) Go to Start ÆSettings ÆControl Panel.
2) Click “Network and Internet Connections”.
3) Click “Network Connections”.

http://www.3jtech.com.tw
http://www.pnpipcameras.com
wifiCAMit User’s Guide
Copyright of 3JTech Co., Ltd. (also doing business asA3J Engineering Inc.)
15
4) Highlight the icon “Local Area Connection”,
right click your mouse, and choose “Properties”
function.
5) Highlight “Internet Protocol (TCP/IP)”, and then press
Properties button.
6) Choose “Use the following IP address”, and then
follow the figure to input the IP address and Subnet
mask. Finally, press OK button to exit the “Internet
Protocol (TCP/IP) Properties” window.
7) Press Close button to close the “Local Area Connection
Properties” window, and then follow eCAMit Deluxe User’s
Guide in CD to install the eCAMit Deluxe software to view
cameras.