3One data RACK2000B User manual

RACK2000B
Media Converter Rack and Rack
Card
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District, Shenzhen
Website: www.3onedata.com
Tel: [phone]
Fax: [phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the media converter rack for the first time.
1.
Media converter rack
2.
Power line
3.
Quick installation guide
4.
Certification
5.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This product is a 16-slot unmanaged card media converter 2U
rack, which could be used with media converter rack card.
The model is:
Model I RACK2000B (16-slot card rack)
Model II Model1100-C1 (100M media converter rack card)
Model IIIModel3012-C 1 (Gigabit media converter rack
card)
【Rack Panel Design】
Front view
Top view
1. Mounting lugs
2. handle
3. Baffle (for placing card device)
【Rack Card Panel Design】
100M Media Converter Rack Card
1. Copper port connection status indicator (TPL)
2. Copper port duplex mode indicator (TRX)
3. 100M fiber port
4. Fiber port connection status indicator (FPL)
5. Power supply connection status indicator (POW)
6. Copper port rate indicator (10/100)
7. Fiber port duplex mode indicator (FRX)
8. 100M copper port
9. Screw
10. Power
Gigabit Media Converter Rack Card
1. LFP (Reserved)

2. Copper port connection status indicator (TPLNK)
3. Copper port duplex mode indicator (DUP)
4. Power supply connection status indicator (PWR)
5. Gigabit fiber port
6. Fiber port connection status indicator (FXLNK)
7. Gigabit copper port
8. Copper port 100M speed indicator (100M)
9. Copper port Gigabit speed indicator (1000M)
10. Screw
11. Power
【Mounting Dimension】
Unit: mm
Rack
100M Media Converter Rack Card
Gigabit Media Converter Rack Card
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Rack-mounted】
Select the device mounting location to ensure
enough size.
Put the device on the plane plate of the rack, and
install the left and right lugs on the rack with 4
screws.
Check and confirm the product is mounted firmly on
the rack, mounting ends.
【Disassembling Device】
Device power off.
Unscrew the fixed mounting lug screw on the rack.
Shift out the device from rack, disassembling ends.
【Power Supply Connection】
Rack AC power supply
The rack has built-in professional communication power
supply, which supports dual power supply redundancy. When
one of the power supplies fails, it could switch to another one
immediately to ensure the device power supply is not
interrupted. Power supply range: 85～265VAC.
This product also supports 48VDC power supply input. The
DC products have the same performance parameters except for
different power inputs.
Rack card DC power supply
The rack card obtains power supply via rack, the power supply
is 5 VDC
【Indicator】
100M Media Converter Rack Card
Category
LED
Indicate
Description
Fiber port
FPL
ON
The connection of fiber
port link is great
Blinking
It exists data
transmission
OFF
The fiber port link is
down
FRX
ON
Full duplex mode
Blinking
It exists conflicts
OFF
Half duplex mode
Copper
Port
TRX
ON
Full duplex mode
Blinking
It exists conflicts
OFF
Half duplex mode
10/100
ON
100Mbps

Category
LED
Indicate
Description
OFF
10Mbps or not working
TPL
ON
Ethernet port is
well-connected
Blinking
It exists data
transmission
OFF
Ethernet port link is
down
Power
supply
POW
ON
Power supply is
running normally
OFF
Power supply is not
running or has fault
Gigabit Media Converter Rack Card
Category
LED
Indicate
Description
Fiber port
FXLNK
ON
The connection of fiber
port link is great
Blinking
It exists data
transmission
OFF
The fiber port has no
data transmission or
the link is down
Copper
Port
100M
ON
100Mbps
OFF
10Mbps or not working
1000M
ON
1000Mbps
OFF
100Mbps or not
working
TPLNK
ON
The copper port link is
well-connected
Blinking
It is transmitting data
OFF
The copper port has no
data transmission or
the link is down
DUP
Blinking
Full duplex mode
Category
LED
Indicate
Description
OFF
Half duplex mode
Alarm
LFP
ON
Reserved
OFF
Reserved
Power
supply
PWR
ON
Power supply is
running normally
OFF
Power supply is not
running or has fault
【Specification】
Panel
Copper Port
10/100Base-T(X) or 10/100/1000
Base-T(X), RJ45 interface,
full/half duplex self-adaption
Fiber port
100Base-FX or 1000Base-FX
fiber port is full-duplex SC/ST/FC
interface
Indicator
Power supply indicator, rate
indicator, duplex indicator, fiber
port indicator, copper port
indicator
Power Supply
Rack input power
supply
AC: dual power supply
85~265VAC, 50~60Hz;
DC: dual power supply
48VDC
Rack output power
supply (rack card
input power supply)
5VDC，16A
Power Consumption
Rack
Full-load: ＜95W
100M rack card
No-load: 1.30W
Full-load: 1.95W
Gigabit rack card
No-load: 1.55W
Full-load: 2.35W
Working
Environment
Rack
Operating temperature: -20~70℃
Storage temperature: -40~70℃
Rack card
Operating temperature: -10~60℃
Storage temperature: -20~70℃
Working humidity
5%～90% (no condensation)